Timer overrides are normally disabled on Nvidia board because
they are commonly wrong, except on new ones with HPET support.
Unfortunately there are quite some Asus boards around that
don't have HPET, but need a timer override.
We don't know yet how to handle this transparently,
but at least add a command line option to force the timer override
and let them boot.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
This refactoring actually optimizes the code a little by caching the value
that we think the device is programmed with instead of reading it back from
the hardware. Which simplifies the code a little and should speed things up a
bit.
This patch introduces the concept of a ht_irq_msg and modifies the
architecture read/write routines to update this code.
There is a minor consistency fix here as well as x86_64 forgot to initialize
the htirq as masked.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Acked-by: Bryan O'Sullivan <bos@pathscale.com>
Cc: <olson@pathscale.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are two bugs in the kretprobe-booster.
1) It doesn't make room for gs registers.
2) It doesn't change status of the current kprobe. This status will
effect the fault handling.
This patch fixes these bugs and, additionally, saves skipped registers for
compatibility with the original kretprobe.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Currently there is no specific alignment restriction in linker script
and in some cases it can be placed non 4K aligned addresses. This fails
kexec which checks that segment to be loaded is page aligned.
o I guess, it does not harm data segment to be 4K aligned.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the microcode driver is built in (rather than module) there are some,
ehm, interesting effects happening due to the new "call out to userspace"
behavior that is introduced.. and which runs too early. The result is a
boot hang; which is really nasty.
The patch below is a minimally safe patch to fix this regression for 2.6.19
by just not requesting actual microcode updates during early boot. (That
is a good idea in general anyway)
The "real" fix is a lot more complex given the entire cpu hotplug scenario
(during cpu hotplug you normally need to load the microcode as well); but
the interactions for that are just really messy at this point; this fix at
least makes it work and avoids a full detangle of hotplug.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/x86_64/kernel/cpufreq/../../../i386/kernel/cpu/cpufreq/speedstep-lib.c:131: error: 'MSR_FSB_FREQ' undeclared (first use in this function)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
On some systems such as the IBM x3650 there are bits set in the
upper half of the control values provided by the _PSS object.
These bits are only relevant for cpufreq drivers that use IO ports
which are not currently supported by the speedstep-centrino driver.
The current MSR oriented code assumes that upper bits are not set
and thus fails to work correctly when they are. e.g. the control
and status value equality check fails even though the ACPI spec
allows the inequality.
Signed-off-by: Gary Hade <garyh@us.ibm.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Several more Intel CPUs are now capable using the p4-clockmod cpufreq
driver. As it is of limited use most of the time, print a big bold warning
if a better cpufreq driver might be available.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Since the "mask" bit is in the low word, when we write a new entry, we
need to write the high word first, before we potentially unmask it.
The exception is when we actually want to mask the interrupt, in which
case we want to write the low word first to make sure that the high word
doesn't change while the interrupt routing is still active.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is preparation for fixing the ordering of the accesses that
got broken by the commit cf4c6a2f27 when
factoring out the "common" io apic routing entry accesses.
Move the accessor function (that were only used by io_apic.c) out
of a header file, and use proper memory-mapped accesses rather than
making up our own "volatile" pointers.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
APM BIOS Interface Secification can now be found at
http://www.microsoft.com/whdc/archive/amp_12.mspx
Signed-off-by: Kristian Mueller <Kristian-M@Kristian-M.de>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
efi_memory_present_wrapper() parameter start/end is physical address, but
function memory_present parameter is PFN, this patch converts physical
address to PFN.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a vmlinux.lds.h helper macro for defining the eight-level initcall table,
teach all the architectures to use it.
This is a prerequisite for a patch which performs initcall synchronisation for
multithreaded-probing.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ Added AVR32 as well ]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jan convinced me that it was unnecessary because the assembly stubs do
this already on the stack.
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
The fake return address was being set to __KERNEL_PDA, rather than 0.
Push it earlier while %eax still equals 0.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Andrew Morton <akpm@osdl.org>
acpi-cpufreq needs the same patch as the previous speedstep-centrino change.
Additionally, the centrino driver can have its ifdef moved out a little
further to eliminate some more code/variables.
Signed-off-by: Dave Jones <davej@redhat.com>
arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c:396: warning: 'sw_any_bug_dmi_table' defined but not used
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
acpi-cpufreq.c, speedstep-centrino.c: warning: 'sw_any_bug_dmi_table' defined but not used
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
- Fixes a build problem with CONFIG_M386=y (include file dependencies get
messy).
- Share the implementation between x86 and x86_64
- These are too big to inline anyway.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Interrupts must be disabled during alternative instruction patching. On
systems with high timer IRQ rates, or when running in an emulator, timing
differences can result in random kernel panics because of running partially
patched instructions. This doesn't yet fix NMIs, which requires extricating
the patch code from the late bug checking and is logically separate (and also
less likely to cause problems).
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If someone inserts speedstep-smi on a mobile P4, it prevents other cpufreq
modules from loading until it is unloaded.
Signed-off-by: Hiroshi Miura <miura@da-cha.org>
Signed-off-by: Dave Jones <davej@redhat.com>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only):
- using allmodconfig
- making sure the files are compiling without any warning/error due to
new changes
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Introduce desc->name and eliminate the handle_irq_name() hack. Add
set_irq_chip_and_handler_name() to set the flow type and name at once.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid possible PIT livelock issues seen on SMP systems (and reported by
Andi), by not allowing it as a clocksource on SMP boxes.
However, since the PIT may no longer be present, we have to properly handle
the cases where SMP systems have TSC skew and fall back from the TSC.
Since the PIT isn't there, it would "fall back" to the TSC again. So this
changes the jiffies rating to 1, and the TSC-bad rating value to 0.
Thus you will get the following behavior priority on i386 systems:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if UP]
jiffies
Rather then the current more complicated:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if cpus < 4]
tsc [if present & unstable]
jiffies
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable ondemand governor and acpi-cpufreq to use IA32_APERF and IA32_MPERF MSR
to get active frequency feedback for the last sampling interval. This will
make ondemand take right frequency decisions when hardware coordination of
frequency is going on.
Without APERF/MPERF, ondemand can take wrong decision at times due
to underlying hardware coordination or TM2.
Example:
* CPU 0 and CPU 1 are hardware cooridnated.
* CPU 1 running at highest frequency.
* CPU 0 was running at highest freq. Now ondemand reduces it to
some intermediate frequency based on utilization.
* Due to underlying hardware coordination with other CPU 1, CPU 0 continues to
run at highest frequency (as long as other CPU is at highest).
* When ondemand samples CPU 0 again next time, without actual frequency
feedback from APERF/MPERF, it will think that previous frequency change
was successful and can go to wrong target frequency. This is because it
thinks that utilization it has got this sampling interval is when running at
intermediate frequency, rather than actual highest frequency.
More information about IA32_APERF IA32_MPERF MSR:
Refer to IA-32 Intel® Architecture Software Developer's Manual at
http://developer.intel.com
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Recent speedstep-centrino unification onto acpi-cpufreq patchset broke
cpuinfo_cur_freq interface in /sys/../cpuinfo/, when MSR was used for
transitions. Attached patch fixes that breakage.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Only change the frequency if the state previously set is different
from what we are trying to set. We don't really have to get the current
frequency at this point.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Mark ACPI hooks in speedstep-centrino as deprecated. Change the order in which
speedstep-centrino and acpi-cpufreq (when both are in kernel) will be
added. First driver to be tried is now acpi-cpufreq, followed by
speedstep-centrino.
Add a note in feature-removal-schedule to mark this deprecation.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Add in the support for Intel Enhanced Speedstep - MSR based transitions.
With this change, the ACPI based support in speedstep-centrino can be
deprecated and duplicate code in that driver can be marked for removal.
Much easier to maintain and support this way. This also reduces the
user misconfigurations and questions on which driver is to be used
under which CPUs to support Enhanced Speedstep.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Some clean up and redsign of the driver. Mainly making it easier to add
support for multiple sub-mechanisms of changing frequency. Currently this
driver supports only ACPI SYSTEM_IO address space. With the changes
below it is easier to add support for other address spaces like Intel
Enhanced Speedstep which uses MSR (ACPI FIXED_FEATURE_HARDWARE) to do the
transitions.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patchset has refresh/rebase of a bunch of patches/bugfixes related to
acpi-cpufreq that were sent earlier on this list.
patch 1/8
Patch that fixes a bug in swcoordination code in acpi-cpufreq
patch 2/8 through patch 7/8
Grand unification of ACPI based speedstep-centrino and acpi-cpufreq drivers.
ACPI allows P-state transitions in multiple ways. Like using IO ports or using
processor native method (MSR). Without this patch, IO port based P-state
transitions are handled in acpi-cpufreq driver and MSR based transitions on
Intel CPUs are handled in speedstep-centrino driver. Even though most of the
code in these two drivers should be similar, except for final changing/checking
of frequency (one driver does it using IO port and other does it through
MSR), we have duplicated code in these two drivers. There are also issues
around BIOSes supporting both MSR and IO port and which driver should be
loaded first in standard installations.
The patchset combines functionality of these two driver into acpi-cpufreq
driver. ACPI based functionality in speedstep-centrino is marked deprecated
and will be removed in future. speedstep-centrino will continue to work
on systems that depend on older non-ACPI table based P-state chanes.
* 2/8 - Patch that reorganizes the code in acpi-cpufreq, cleaning it up
a little and making it easier to add MSR support later.
* 3/8 - Pull in the MSR based transition support into acpi-cpufreq.
* 4/8 - Mark speedstep-centrino deprecated. Change the order in Makefile to
load acpi-cpufreq first and speedstep-centrino later, in cases where both
are configured in.
* 5/8 - lindent acpi-cpufreq.c
* 6/8 - Minor change to eliminate the check of current frequency on
notifications. We can use last set frequency instead.
* 7/8 - Make cpufreq->get of acpi_cpufreq work correctly again.
There will be a patch in future that removes ACPI based support in
speedstep-centrino in coming months.
patch 8/8
Add support for IA32_APERF and IA32_MPERF MSR and get the actual frequency
from these MSRs and use it to determine the next frequency target in ondemand
governor
This patch:
There is a bug in software coordination patch in acpi-cpufreq, due to which
frequency will only be set on first CPU of any coordinated group.
Bug identified by Denis, was not recognised earlier as there are no platforms
yet that use software coordination with acpi-cpufreq driver.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The Linux group at Stratus Technologies has come across an issue with SCI
routing under ACPI. We were bitten by this when we made an x86_64 platform
whose BIOS provides an Interrupt Source Override for the SCI itself.
Apparently the override has no effect for the System Control Interrupt, and
this appears to be because of the way the SCI is setup in the ACPI code.
It does not handle the case where busirq != gsi.
The code that sets up the SCI routing assumes that bus irq == global irq.
So there is simply no provision for telling it otherwise. The attached
patch provides this mechanism.
This patch provided by David Bulkow, was tested on an i386 platform, which
does not use the SCI override, and also on an x86_64 platform which does
use an override.
Signed-off-by: David Bulkow <david.bulkow@stratus.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel processors starting with the Core Duo support
support processor native C-state using the MWAIT instruction.
Refer: Intel Architecture Software Developer's Manual
http://www.intel.com/design/Pentium4/manuals/253668.htm
Platform firmware exports the support for Native C-state to OS using
ACPI _PDC and _CST methods.
Refer: Intel Processor Vendor-Specific ACPI: Interface Specification
http://www.intel.com/technology/iapc/acpi/downloads/302223.htm
With Processor Native C-state, we use 'MWAIT' instruction on the processor
to enter different C-states (C1, C2, C3). We won't use the special IO
ports to enter C-state and no SMM mode etc required to enter C-state.
Overall this will mean better C-state support.
One major advantage of using MWAIT for all C-states is, with this and
"treat interrupt as break event" feature of MWAIT, we can now get accurate
timing for the time spent in C1, C2, .. states.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Get rid of warning in the thermal throttling code about not checking
sysfs return values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement the epoll_pwait system call, that extend the event wait mechanism
with the same logic ppoll and pselect do. The definition of epoll_pwait
is:
int epoll_pwait(int epfd, struct epoll_event *events, int maxevents,
int timeout, const sigset_t *sigmask, size_t sigsetsize);
The difference between the vanilla epoll_wait and epoll_pwait is that the
latter allows the caller to specify a signal mask to be set while waiting
for events. Hence epoll_pwait will wait until either one monitored event,
or an unmasked signal happen. If sigmask is NULL, the epoll_pwait system
call will act exactly like epoll_wait. For the POSIX definition of
pselect, information is available here:
http://www.opengroup.org/onlinepubs/009695399/functions/select.html
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andi Kleen <ak@muc.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
hw_interrupt_type is deprecated in favour of struct irq_chip.
[mingo@elte.hu: do x86_64 too]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arch-independent zone-sizing is using indices instead of symbolic names to
offset within an array related to zones (max_zone_pfns). The unintended
impact is that ZONE_DMA and ZONE_NORMAL is initialised on powerpc instead
of ZONE_DMA and ZONE_HIGHMEM when CONFIG_HIGHMEM is set. As a result, the
the machine fails to boot but will boot with CONFIG_HIGHMEM turned off.
The following patch properly initialises the max_zone_pfns[] array and uses
symbolic names instead of indices in each architecture using
arch-independent zone-sizing. Two users have successfully booted their
powerpcs with it (one an ibook G4). It has also been boot tested on x86,
x86_64, ppc64 and ia64. Please merge for 2.6.19-rc2.
Credit to Benjamin Herrenschmidt for identifying the bug and rolling the
first fix. Additional credit to Johannes Berg and Andreas Schwab for
reporting the problem and testing on powerpc.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Which vector an irq is assigned to now varies dynamically and is
not needed outside of io_apic.c. So remove the possibility
of accessing the information outside of io_apic.c and remove
the silly macro that makes looking for users of irq_vector
difficult.
The fact this compiles ensures there aren't any more pieces
of the old CONFIG_PCI_MSI weirdness that I failed to remove.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
