This patch improves the serial port communication quality
of port YC401 on the KFR2R09 board. With this fix serial
console is fine at 115200 - up and down keys now work as
expected. Thanks to Hirohide Yamasaki for this fix.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This file breaks out the SuperH PFC code from
arch/sh/kernel/gpio.c + arch/sh/include/asm/gpio.h
to drivers/sh/pfc.c + include/linux/sh_pfc.h.
Similar to the INTC stuff. The non-SuperH specific
file location makes it possible to share the code
between multiple architectures.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves the KEYSC header file from the
SuperH specific asm directory to a place where
it can be shared by multiple architectures.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7724 code to save and restore CPG state during
R-standby. Only CPG registers IRDACLKCR and SPUCLKCR
require software save and restore.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for SDHI power control to the
Ecovec board. Platform data and power control callbacks
for SDHI0 and SDHI1 are added. Power is by default off.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data with a function for power
control to the SDHI driver. The idea is that board specific
code can provide their own functions so power can be enabled
and disabled for the sd-cards.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This driver has been mostly rewritten since Michael Brown's initial
work, so swap the order of the authors.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This integrates support for the SFC9000 family of 10G Ethernet
controllers and LAN-on-motherboard chips, starting with the SFL9021
'Siena' and SFC9020 'Bethpage'.
Credit for this code is largely due to my colleagues at Solarflare:
Guido Barzini
Steve Hodgson
Kieran Mansley
Matthew Slattery
Neil Turton
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the SFC9000 family of 10G Ethernet controllers
and LAN-on-motherboard chips, starting with the SFL9021 'Siena' and
SFC9020 'Bethpage'.
The SFC9000 family is based on the SFC4000 'Falcon' architecture, but
with some significant changes:
- Two ports are associated with two independent PCI functions
(except SFC9010)
- Integrated 10GBASE-T PHY(s) (SFL9021/9022)
- MAC, PHY and board peripherals are managed by firmware
- Driver does not require board-specific code
- Firmware supports wake-on-LAN and lights-out management through NC-SI
- IPv6 checksum offload and RSS
- Filtering by MAC address and VLAN (not included in this code)
- PCI SR-IOV (not included in this code)
Credit for this code is largely due to my colleagues at Solarflare:
Guido Barzini
Steve Hodgson
Kieran Mansley
Matthew Slattery
Neil Turton
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In new NICs flash is managed by firmware and we will use high-level
operations on partitions rather than direct SPI commands. Add support
for multiple MTD partitions per flash device and remove the direct
link between MTD and SPI devices. Maintain a list of MTD partitions
in struct efx_nic.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New NICs have firmware managing the PHY, and we will discover the PHY
capabilities at run-time. Replace the static data with probe() and
test_name() operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New NICs and PHYs support a wider variety of loopback modes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
falcon_probe_nic_variant() does a lot less than it used to, and a
lot less than it claims to. Fold the remainder into its caller.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_alloc_consistent uses GFP_ATOMIC allocation that may fail on some systems
with limited memory (Bug #14265). pci_pool_alloc allows waiting with
GFP_KERNEL.
Tested-by: Karol Lewandowski <karol.k.lewandowski@gmail.com>
Signed-off-by: Roger Oksanen <roger.oksanen@cs.helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not including net/atm/
Compiled tested x86 allyesconfig only
Added a > 80 column line or two, which I ignored.
Existing checkpatch plaints willfully, cheerfully ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor efx_reset_down() and efx_reset_up() accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake-on-LAN is a stub for Falcon, but will be implemented fully for
new NICs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the efx_nic_type::monitor operation or event handling as
appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor PHY, MAC and NIC configuration operations so that the
existing link configuration can be re-pushed with:
efx->phy_op->reconfigure(efx);
efx->mac_op->reconfigure(efx);
and a new configuration with:
efx->nic_op->reconfigure_port(efx);
(plus locking and error-checking).
We have not held the link settings in software (aside from flow
control), and have relied on asking the hardware what they are. This
is a problem because in some cases the hardware may no longer be in a
state to tell us. In particular, if an entire multi-port board is
reset through one port, the driver bindings to other ports have no
chance to save settings before recovering.
We only actually need to keep track of the autonegotiation settings,
so add an ethtool advertising mask to struct efx_nic, initialise it
in PHY init and update it as necessary.
Remove now-unneeded uses of efx_phy_op::{get,set}_settings() and
struct ethtool_cmd.
Much of this was done by Steve Hodgson <shodgson@solarflare.com>.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preparation for adding differing implementations for new NICs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause frame generation is gated by both RX_XOFF_MAC_EN and an enable
bit in each MAC. RX_XOFF_MAC_EN bit always reads back as 0 so we need
to set it correctly every time we modify RX_CFG_REG. Simplify this by
always setting it to 1 and only changing the enable bits in the MACs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register only needs to be written after reset, not each time we
enable interrupts.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fork() clones all thread_info flags, including
TIF_USER_RETURN_NOTIFY; if the new task is first scheduled on a cpu
which doesn't have user return notifiers set, this causes user
return notifiers to trigger without any way of clearing itself.
This is easy to trigger with a forky workload on the host in
parallel with kvm, resulting in a cpu in an endless loop on the
verge of returning to userspace.
Fix by dropping the TIF_USER_RETURN_NOTIFY immediately after fork.
Signed-off-by: Avi Kivity <avi@redhat.com>
LKML-Reference: <1259505288-16559-1-git-send-email-avi@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch (as1305) fixes a bug in the irq-enable settings and removes
some related overhead in the runtime PM code.
In __pm_runtime_resume(), within the scope of the original
spin_lock_irq(), we know that irqs are disabled. There's no
reason to go through a pair of enable/disable cycles when
acquiring and releasing the parent's lock.
In __pm_runtime_set_status(), irqs are already disabled when
the parent's lock is acquired, and they must remain disabled
when it is released.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
pktgen threads are bound to given CPU, we can allocate memory for
these threads in a NUMA aware way.
After a pktgen session on two threads, we can check flows memory was
allocated on right node, instead of a not related one.
# grep pktgen_thread_write /proc/vmallocinfo
0xffffc90007204000-0xffffc90007385000 1576960 pktgen_thread_write+0x3a4/0x6b0 [pktgen] pages=384 vmalloc N0=384
0xffffc90007386000-0xffffc90007507000 1576960 pktgen_thread_write+0x3a4/0x6b0 [pktgen] pages=384 vmalloc N1=384
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the ethtool interface to display what PHY
is currently connected to a NIC. The results can be viewed in
ethtool ethX output.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a base driver to specify Direct Attach as the
type of port through the ethtool interface.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an issue when clearing out the RAR entries. If RAR[0]
is the only address in use, don't clear the others.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82598 shouldn't try and access LINKS2 while configuring
link and flow control. This is an 82599-only register.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow Control autoneg should be disabled for certain adapters
that don't support autonegotiation of Flow Control at 10 gigabit.
These interfaces are the 10GBASE-T devices, CX4, and SFP+, all
running at 10 gigabit only. 1 gigabit is fine.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was doing a divide by zero when adjusting tx-usecs.
This patch removes the divide by zero code and changes the logic slightly
to ignore tx-usecs in the case of shared TxRx vectors.
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calls to x25_dev_get check for dev = NULL which was not set.
It allowed x25 to set routes and ioctls on down interfaces.
This caused oopses and refcnt problems on device_unregister.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the CONFIG_SYSCTL ifdefs in x25_init into header.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert smc91x driver from legacy PM hooks over to using dev_pm_ops.
Tested on OMAP3 platform.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
