When both soft and hard resets are available, libata preferred
softreset till now. The logic behind it was to be softer to devices;
however, this doesn't really help much. Rationales for the change:
* BIOS may freeze lock certain things during boot and softreset can't
unlock those. This by itself is okay but during operation PHY event
or other error conditions can trigger hardreset and the device may
end up with different configuration.
For example, after a hardreset, previously unlockable HPA can be
unlocked resulting in different device size and thus revalidation
failure. Similar condition can occur during or after resume.
* Certain ATAPI devices require hardreset to recover after certain
error conditions. On PATA, this is done by issuing the DEVICE RESET
command. On SATA, COMRESET has equivalent effect. The problem is
that DEVICE RESET needs its own execution protocol.
For SFF controllers with bare TF access, it can be easily
implemented but more advanced controllers (e.g. ahci and sata_sil24)
require specialized implementations. Simply using hardreset solves
the problem nicely.
* COMRESET initialization sequence is the norm in SATA land and many
SATA devices don't work properly if only SRST is used. For example,
some PMPs behave this way and libata works around by always issuing
hardreset if the host supports PMP.
Like the above example, libata has developed a number of mechanisms
aiming to promote softreset to hardreset if softreset is not going
to work. This approach is time consuming and error prone.
Also, note that, dependingon how you read the specs, it could be
argued that PMP fan-out ports require COMRESET to start operation.
In fact, all the PMPs on the market except one don't work properly
if COMRESET is not issued to fan-out ports after PMP reset.
* COMRESET is an integral part of SATA connection and any working
device should be able to handle COMRESET properly. After all, it's
the way to signal hardreset during reboot. This is the most used
and recommended (at least by the ahci spec) method of resetting
devices.
So, this patch makes libata prefer hardreset over softreset by making
the following changes.
* Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever
ATA_EH_{SOFT|HARD}RESET used to be used. ATA_EH_{SOFT|HARD}RESET is
now only used to tell prereset whether soft or hard reset will be
issued.
* Strip out now unneeded promote-to-hardreset logics from
ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and
other places.
Signed-off-by: Tejun Heo <htejun@gmail.com>
* remove changelog from source; its kept in git repository
* consolidate descriptor version tests using nv_optimized()
* consolidate NIC DMA start, stop and drain into
nv_start_txrx(), nv_stop_txrx(), nv_drain_txrx()
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We were already doing what amounts to a get_phy_id from within
get_phy_device, and rather than duplicate this for the TBIPA
probing, we might as well just factor it out and make it available
instead.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The BCM5464 can be used with the current broadcom PHY driver
by just adding the appropriate chip ID and using the existing
support within.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the warning:
drivers/net/cxgb3/cxgb3_main.c: In function ‘offload_open’:
drivers/net/cxgb3/cxgb3_main.c:936: warning: ignoring return value of
‘sysfs_create_group’, declared with attribute warn_unused_result
Now the return value is checked; if sysfs_create_group() returns failure,
a warning is printed using dev_dbg, and the code continues as before. Use
of dev_dbg ensures printk is not needlessly included unless desired for
debugging.
Signed-off-by: Dan Noe <dpn@isomerica.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On Sat, 12 Apr 2008 05:00:49 -0400, Jeff Garzik <jeff@garzik.org> wrote:
> applied 1-6
Thanks.
Could you apply this too, or hopufully fold into Andy Fleming's "phy:
Change mii_bus id field to a string" patch (commit c69fedae) ?
------------------------------------------------------
Subject: [PATCH] tc35815: build fix
Fix build failure caused by Andy Fleming's "phy: Change mii_bus id
field to a string" patch.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The driver stores the PCI resource address into 'unsigned long' variable before
calling ioremap() on it. This warrants a kernel oops when the registers are
accessed on PPC 44x platforms which (being 32-bit) have PCI memory space mapped
beyond 4 GB.
The arch/ppc/ kernel has a fixup in ioremap() that creates an illusion of the
PCI memory resources are mapped below 4 GB, but arch/powerpc/ code got rid of
this trick, having instead CONFIG_RESOURCES_64BIT enabled.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On the ppc 4xx architecture the instruction cache must be flushed as
well as the data cache. This patch just makes it generic for all
architectures where CACHE_FLUSH_IS_SAFE is set to 1.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the problem of protecting the kgdb handle_exception exit
which had an NMI race condition, while trying to restore
normal system operation.
There was a small window after the master processor sets cpu_in_debug
to zero but before it has set kgdb_active to zero where a
non-master processor in an SMP system could receive an NMI and
re-enter the kgdb_wait() loop.
As long as the master processor sets the cpu_in_debug before sending
the cpu roundup the cpu_in_debug variable can also be used to guard
against the race condition.
The kgdb_wait() function no longer needs to check
kgdb_active because it is done in the arch specific code
and handled along with the nmi traps at the low level.
This also allows kgdb_wait() to exit correctly if it was
entered for some unknown reason due to a spurious NMI that
could not be handled by the arch specific code.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds in the ability to compile the kgdb internal test
string into the kernel so as to run the tests at boot without changing
the kernel boot arguments. This patch also changes all the error
paths to invoke WARN_ON(1) which will emit the line number of the file
and dump the kernel stack when an error occurs.
You can disable the tests in a kernel that is built this way
using "kgdbts="
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds regression tests for testing the kgdb core and arch
specific implementation.
The kgdb test suite is designed to be built into the kernel and not as
a module because it uses a number of low level kernel and kgdb
primitives which should not be exported externally.
The kgdb test suite is designed as a KGDB I/O module which
simulates the communications that a debugger would have with kgdb.
The tests are broken up in to a line by line and referenced here as
a "get" which is kgdb requesting input and "put" which is kgdb
sending a response.
The kgdb suite can be invoked from the kernel command line
arguments system or executed dynamically at run time. The test
suite uses the variable "kgdbts" to obtain the information about
which tests to run and to configure the verbosity level. The
following are the various characters you can use with the kgdbts=
line:
When using the "kgdbts=" you only choose one of the following core
test types:
A = Run all the core tests silently
V1 = Run all the core tests with minimal output
V2 = Run all the core tests in debug mode
You can also specify optional tests:
N## = Go to sleep with interrupts of for ## seconds
to test the HW NMI watchdog
F## = Break at do_fork for ## iterations
S## = Break at sys_open for ## iterations
NOTE: that the do_fork and sys_open tests are mutually exclusive.
To invoke the kgdb test suite from boot you use a kernel start
argument as follows:
kgdbts=V1 kgdbwait
Or if you wanted to perform the NMI test for 6 seconds and do_fork
test for 100 forks, you could use:
kgdbts=V1N6F100 kgdbwait
The test suite can also be invoked at run time with:
echo kgdbts=V1N6F100 > /sys/module/kgdbts/parameters/kgdbts
Or as another example:
echo kgdbts=V2 > /sys/module/kgdbts/parameters/kgdbts
When developing a new kgdb arch specific implementation or
using these tests for the purpose of regression testing,
several invocations are required.
1) Boot with the test suite enabled by using the kernel arguments
"kgdbts=V1F100 kgdbwait"
## If kgdb arch specific implementation has NMI use
"kgdbts=V1N6F100
2) After the system boot run the basic test.
echo kgdbts=V1 > /sys/module/kgdbts/parameters/kgdbts
3) Run the concurrency tests. It is best to use n+1
while loops where n is the number of cpus you have
in your system. The example below uses only two
loops.
## This tests break points on sys_open
while [ 1 ] ; do find / > /dev/null 2>&1 ; done &
while [ 1 ] ; do find / > /dev/null 2>&1 ; done &
echo kgdbts=V1S10000 > /sys/module/kgdbts/parameters/kgdbts
fg # and hit control-c
fg # and hit control-c
## This tests break points on do_fork
while [ 1 ] ; do date > /dev/null ; done &
while [ 1 ] ; do date > /dev/null ; done &
echo kgdbts=V1F1000 > /sys/module/kgdbts/parameters/kgdbts
fg # and hit control-c
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
kgdb core fixes:
- Check to see that mm->mmap_cache is not null before calling
flush_cache_range(), else on arch=ARM it will cause a fatal
fault.
- Breakpoints should only be restored if they are in the BP_ACTIVE
state.
- Fix a typo in comments to "kgdb_register_io_module"
x86 kgdb fixes:
- Fix the x86 arch handler such that on a kill or detach that the
appropriate cleanup on the single stepping flags gets run.
- Add in the DIE_NMIWATCHDOG call for x86_64
- Touch the nmi watchdog before returning the system to normal
operation after performing any kind of kgdb operation, else
the possibility exists to trigger the watchdog.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implement the serial polling hooks for the pl011 uart for use with
kgdboc.
This patch was specifically tested on the ARM Versatile AB reference
platform.
[ mingo@elte.hu: minor cleanups. ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix two regressions dealing with the kgdb core.
1) kgdb_skipexception and kgdb_post_primary_code are optional
functions that are only required on archs that need special exception
fixups.
2) The kernel address space scope must be set on any probe_kernel_*
function or archs such as ARCH=arm will not allow access to the kernel
memory space. As an example, it is required to allow the full kernel
address space is when you the kernel debugger to inspect a system
call.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add HW breakpoints into the arch specific portion of x86 kgdb. In the
current x86 kernel.org kernels HW breakpoints are changed out in lazy
fashion because there is no infrastructure around changing them when
changing to a kernel task or entering the kernel mode via a system
call. This lazy approach means that if a user process uses HW
breakpoints the kgdb will loose out. This is an acceptable trade off
because the developer debugging the kernel is assumed to know what is
going on system wide and would be aware of this trade off.
There is a minor bug fix to the kgdb core so as to correctly call the
hw breakpoint functions with a valid value from the enum.
There is also a minor change to the x86_64 startup code when using
early HW breakpoints. When the debugger is connected, the cpu startup
code must not zero out the HW breakpoint registers or you cannot hit
the breakpoints you are interested in, in the first place.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If kgdb does remove a breakpoint that had a problem on the recursion
check, it should also print the address of the breakpoint.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In order to not trip the clocksource watchdog, kgdb must touch the
clocksource watchdog on the return to normal system run state.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes the hang regression with kgdb when the NMI interrupt
comes in while the master core is returning from an exception.
Adjust the NMI logic such that KGDB will not stop NMI exceptions from
occurring by in general returning NOTIFY_DONE. It is not possible to
distinguish the debug NMI sync vs the normal NMI apic interrupt so
kgdb needs to catch the unknown NMI if it the debugger was previously
active on one of the cpus.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the run time configuration of kgdboc such that it does not default
to 9600 baud if you use the "echo" command to configure the sysfs
module paramater.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
simplified and streamlined kgdb support on x86, both 32-bit and 64-bit,
based on patch from:
Subject: kgdb: core-lite
From: Jason Wessel <jason.wessel@windriver.com>
[ and countless other authors - see the patch for details. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
polled console handling support, to access a console in an irq-less
way while in debug or irq context.
absolutely zero impact as long as CONFIG_CONSOLE_POLL is disabled.
(which is the default)
[ jan.kiszka@siemens.com: lots of cleanups ]
[ mingo@elte.hu: redesign, splitups, cleanups. ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
kgdb core code. Handles the protocol and the arch details.
[ mingo@elte.hu: heavily modified, simplified and cleaned up. ]
[ xemul@openvz.org: use find_task_by_pid_ns ]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jan Kiszka <jan.kiszka@web.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
add probe_kernel_read() and probe_kernel_write().
Uninlined and restricted to kernel range memory only, as suggested
by Linus.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
There's no point for an in-kernel driver to check whether it's compiled
under kernel < 2.6.0 .
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
as seen in linux-next tree:
drivers/s390/scsi/zfcp_dbf.c: In function ‘zfcp_rec_dbf_event_thread’:
drivers/s390/scsi/zfcp_dbf.c:697: warning: passing argument 1 of ‘atomic_read’
from incompatible pointer type
Caused by recent git commit:
commit 348447e857
Author: Martin Peschke <mp3@de.ibm.com>
Date: Thu Mar 27 14:22:01 2008 +0100
[SCSI] zfcp: Add trace records for recovery thread and its queues
We are not supposed to poke inside semaphore.
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Move wakeup code to .c, so that video mode setting code can be shared
between boot and wakeup. Remove nasty assembly code in 64-bit case by
re-using trampoline code. Stack setup was fixed to clear high 16bits
of %esp, maybe that fixes some machines.
.c code sharing and morse code was done H. Peter Anvin, Sam Ravnborg
reviewed kbuild related stuff, and it seems okay to him. Rafael did
some cleanups.
[rjw:
* Made the patch stop breaking compilation on x86-32
* Added arch/x86/kernel/acpi/sleep.h
* Got rid of compiler warnings in arch/x86/kernel/acpi/sleep.c
* Fixed 32-bit compilation on x86-64 systems
* Added include/asm-x86/trampoline.h and fixed the non-SMP
compilation on 64-bit x86
* Removed arch/x86/kernel/acpi/sleep_32.c which was not used
* Fixed some breakage caused by the integration of smpboot.c done
under us in the meantime]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
this patch fixes section mismatch warnings (on x86_64 host) in setup_trampoline(),
which was referencing __initdata variables trampoline_data and trampoline_end.
Warning messages:
WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x2b6a): Section mismatch in reference from the function setup_trampoline()
to the variable .init.data:trampoline_data
The function __cpuinit setup_trampoline() references
a variable __initdata trampoline_data.
If trampoline_data is only used by setup_trampoline then
annotate trampoline_data with a matching annotation.
WARNING: arch/x86/kernel/built-in.o(.cpuinit.text+0x2b71): Section mismatch in reference from the function setup_trampoline()
to the variable .init.data:trampoline_end
The function __cpuinit setup_trampoline() references
a variable __initdata trampoline_end.
If trampoline_end is only used by setup_trampoline then
annotate trampoline_end with a matching annotation.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes mismatch warnings in smp_checks() (in arch/x86/kernel/smpboot.c):
WARNING: arch/x86/kernel/built-in.o(.text+0x11922): Section mismatch in reference from the function smp_checks()
to the variable .cpuinit.data:smp_b_stepping
The function smp_checks() references
the variable __cpuinitdata smp_b_stepping.
This is often because smp_checks lacks a __cpuinitdata
annotation or the annotation of smp_b_stepping is wrong.
Signed-off-by: Jacek Luczak <luczak.jacek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
> > Make sure that we clear the "shutdown status flag" in the CMOS
> > register after each CPU is brought up. This fixes a problem where the
> > "shutdown status flag" may remain set when a CPU is brought up after
> > booting.
>
> btw., what problem does this result in, exactly?
The shutdown status flag set to "0xA", corresponds to "JMP double word
request without INT init".
This JMP at reboot time is at an unintended location. And results in
Triple faults in our case.
Though this error at reboot can be safely ignored in a VM environment,
am not sure what the effect would be on a physical system. May be it
will result in a triple fault and an eventual hardware reset thus
masking this BUG in the kernel.
This fix just makes sure that we reset that status flag after
initialization is done.
Fix paranoia about using BIOS quickboot mechanism.
Make sure that we clear the "shutdown status flag" in the CMOS register
after each CPU is brought up. This fixes a problem where the "shutdown
status flag" may remain set when a CPU is brought up after booting.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Dan Arai <arai@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use cpumask_of_cpu() rather than the pair of cpus_clear() and cpu_set().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
No need to clear the memory allocated by alloc_bootmem().
It is already filled with zero.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove duplicate code by using ioapic_read_entry() and ioapic_write_entry()
in io_apic_{32,64}.c
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If one can find an ack pending pin, there is no need to check
the rest of them.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
