This reverts commit 135aedc38e, as
requested by Hans Verkuil.
It was a patch for 2.6.28 where the BKL was pushed down from v4l core to
the drivers, not for 2.6.27!
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for NOR and NAND flashes on CM-X255.
The NAND flash support uses not yet merged GPIO NAND driver.
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Change CM-X255 and CM-X270 common function prefix from cmx270 to cmx2xx
- Split cmx2xx_init to common and CM-X270-specific parts
- Use dynamic assignement for DM9000 resources and led GPIOs.
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for Trizeps4 SOM PCMCIA
with ConXS or other baseboards.
with double GPIO-free fixed (sorry!)
replaces 5279/1
Signed-off-by: Jurgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds defines for the external chipselect physical base
addresses available with the EP93xx. These are meant to be used
in the platform init code.
In addition, documentation about the synchronous/asynchronous boot
modes for the EP93xx and a reference to errata about issues with
synchronous booting has been added.
Signed-off-by: <H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The association response IEs are sent to userland with an IWEVCUSTOM
event, which unfortunately is limited to a little more than 100 bytes
of IE information with the encoding used. Many APs send so much
IE information that this message overflows. When the IWEVCUSTOM
event is too large, the kernel doesn't send it to userland anyway --
better just not to send it.
An attempt was made by Jouni Malinen to correct this issue by
converting to use IWEVASSOCREQIE and IWEVASSOCRESPIE messages instead
("mac80211: Use IWEVASSOCREQIE instead of IWEVCUSTOM"). Unfortunately,
that caused a problem due to 32-/64-bit interactions on some systems and
was reverted after the 'userland ABI' rule was invoked. That leaves
us with this option instead of a proper fix, at least until we move
to a cfg80211-based solution.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Theodore Ts'o (tytso@mit.edu) wrote:
>
> I've been playing with adding some markers into ext4 to see if they
> could be useful in solving some problems along with Systemtap. It
> appears, though, that as of 2.6.27-rc8, markers defined in code which is
> compiled directly into the kernel (i.e., not as modules) don't show up
> in Module.markers:
>
> kvm_trace_entryexit arch/x86/kvm/kvm-intel %u %p %u %u %u %u %u %u
> kvm_trace_handler arch/x86/kvm/kvm-intel %u %p %u %u %u %u %u %u
> kvm_trace_entryexit arch/x86/kvm/kvm-amd %u %p %u %u %u %u %u %u
> kvm_trace_handler arch/x86/kvm/kvm-amd %u %p %u %u %u %u %u %u
>
> (Note the lack of any of the kernel_sched_* markers, and the markers I
> added for ext4_* and jbd2_* are missing as wel.)
>
> Systemtap apparently depends on in-kernel trace_mark being recorded in
> Module.markers, and apparently it's been claimed that it used to be
> there. Is this a bug in systemtap, or in how Module.markers is getting
> built? And is there a file that contains the equivalent information
> for markers located in non-modules code?
I think the problem comes from "markers: fix duplicate modpost entry"
(commit d35cb360c2)
Especially :
- add_marker(mod, marker, fmt);
+ if (!mod->skip)
+ add_marker(mod, marker, fmt);
}
return;
fail:
Here is a fix that should take care if this problem.
Thanks for the bug report!
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Tested-by: "Theodore Ts'o" <tytso@mit.edu>
CC: Greg KH <greg@kroah.com>
CC: David Smith <dsmith@redhat.com>
CC: Roland McGrath <roland@redhat.com>
CC: Sam Ravnborg <sam@ravnborg.org>
CC: Wenji Huang <wenji.huang@oracle.com>
CC: Takashi Nishiie <t-nishiie@np.css.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes STATUS_CONF_PENDING usage that called from
iwl4965_mac_config internally after scan completed.
It's called anyway from the mac80211 ieee80211_scan_completed():
if (local->hw_scanning) {
local->hw_scanning = false;
if (ieee80211_hw_config(local))
...
}
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves comment to proper line, it has moved during
code shuffling.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets rx_chain bitmap correctly according hw configuration.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up the tx status reporting, fix retry counters (short retries are
virtual collisions, not actual retries). Implement multi-rate retry
support.
This also fixes strong throughput fluctuations with rc80211_pid
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adjusts the rate control API to allow multi-rate retry
if supported by the driver. The ieee80211_hw struct specifies how
many alternate rate selections the driver supports.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free up 2 bytes in skb->cb to be used for multi-rate retry later.
Move iv_len and icv_len initialization into key alloc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LED state was not being updated by rfkill_force_state(), which
will cause regressions in wireless drivers that had old-style rfkill
support and are updated to use rfkill_force_state().
The LED state was not being updated when a change was detected through
the rfkill->get_state() hook, either.
Move the LED trigger update calls into notify_rfkill_state_change(),
where it should have been in the first place. This takes care of both
issues above.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The state field of the rfkill structure was incorrectly initialized to -1, which results in rfkill
issueing a WARN_ON. Fix this by initializing the state field to the proper value as indicated by
the driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- This patch (against the linux-wireless-next git tree) removes a
redundant check in ieee80211_master_start_xmit (net/mac80211/tx.c)
and adjust indentation in this method accordingly.
In this method, there is no need to call again the
ieee80211_is_data() method; this is checked immediately before, in the
"if" command (we will not enter this block unless ieee80211_is_data()
is true, so that the "and" (&&) condition in that "if" command will be
fullfilled ).
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the a few lines that went missing in
"p54: 802.11a 5GHz phy support"
Essentially: the rx-code wasn't updated and therefore reported the wrong band,
but more importantly the rate index was off as well, since 802.11a doesn't
allow the "four" 802.11b rates...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables Adaptive Noise Immunity (ANI) on ath9k.
ANI is as algorithm designed to minimize the detrimental
effects of time-varying interferences. This should
help with throughput in noisy environments. To use
ANI we re-enable the MIB interrupt. Since ANI works
on a timer and updates the noise floor we take
advantage of this and also report a non-static noise
floor now to mac80211.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were trying to hold the wrong spinlock due to a typo
on IEEE80211_BAR_CTL_TID_S's definition. We use this to
compute the tid number and then hold this this tid number's
spinlock.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part of the cleanup on ath9k -- this was also causing some
annoying compile time warnings.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes doubly defined variables in ieee80211_master_start_xmit
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restore revert "mac80211: Use IWEVASSOCREQIE instead of IWEVCUSTOM",
originally reverted in commit bf7394ccc1.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We only need to set them when we call SetFileInfo or SetPathInfo
directly, and as soon as possible after then. We had one place setting
it where it didn't need to be, and another place where it was missing.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Since IPVS now has partial IPv6 support, this patch moves IPVS from
net/ipv4/ipvs to net/netfilter/ipvs. It's a result of:
$ git mv net/ipv4/ipvs net/netfilter
and adapting the relevant Kconfigs/Makefiles to the new path.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: gart iommu have direct mapping when agp is present too
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: workaround for bogus gcc warning in ide_sysfs_register_port()
ide-cd: Optiarc DVD RW AD-7200A does play audio
IDE: Fix platform device registration in Swarm IDE driver (v2)
ide-dma: fix ide_build_dmatable() for TRM290
ide-cd: temporary tray close fix
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] IP27: Fix build errors if CONFIG_MAPPED_KERNEL=y
[MIPS] Fix CMP Kconfig configuration and mark as broken.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (33 commits)
V4L/DVB (9103): em28xx: HVR-900 B3C0 - fix audio clicking issue
V4L/DVB (9099): em28xx: Add detection for K-WORLD DVB-T 310U
V4L/DVB (9092): gspca: Bad init values for sonixj ov7660.
V4L/DVB (9080): gspca: Add a delay after writing to the sonixj sensors.
V4L/DVB (9075): gspca: Bad check of returned status in i2c_read() spca561.
V4L/DVB (9053): fix buffer overflow in uvc-video
V4L/DVB (9043): S5H1420: Fix size of shadow-array to avoid overflow
V4L/DVB (9037): Fix support for Hauppauge Nova-S SE
V4L/DVB (9029): Fix deadlock in demux code
V4L/DVB (8979): sms1xxx: Add new USB product ID for Hauppauge WinTV MiniStick
V4L/DVB (8978): sms1xxx: fix product name for Hauppauge WinTV MiniStick
V4L/DVB (8967): Use correct XC3028L firmware for AMD ATI TV Wonder 600
V4L/DVB (8963): s2255drv field count fix
V4L/DVB (8961): zr36067: Fix RGBR pixel format
V4L/DVB (8960): drivers/media/video/cafe_ccic.c needs mm.h
V4L/DVB (8958): zr36067: Return proper bytes-per-line value
V4L/DVB (8957): zr36067: Restore the default pixel format
V4L/DVB (8955): bttv: Prevent NULL pointer dereference in radio_open
V4L/DVB (8935): em28xx-cards: Remove duplicate entry (EM2800_BOARD_KWORLD_USB2800)
V4L/DVB (8933): gspca: Disable light frquency for zc3xx cs2102 Kokom.
...
The atmel-mci driver sometimes fails data transfers like this:
mmcblk0: error -5 transferring data
end_request: I/O error, dev mmcblk0, sector 2749769
end_request: I/O error, dev mmcblk0, sector 2749777
It turns out that this might be caused by the BLKR register (which
contains the block size and the number of blocks being transfered) being
initialized too late. This patch moves the initialization of BLKR so
that it contains the correct value before the block transfer command is
sent.
This error is difficult to reproduce, but if you insert a long delay
(mdelay(10) or thereabouts) between the calls to atmci_start_command()
and atmci_submit_data(), all transfers seem to fail without this patch,
while I haven't seen any failures with this patch.
Reported-by: Hein_Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While debugging another bug it was found that NetRom socks
are sometimes seen unorphaned in sk_free(). This patch moves
sock_orphan() in nr_release() to the beginning (like in ax25,
or rose).
Reported-and-tested-by: Bernard Pidoux f6bvp <f6bvp@free.fr>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we reverted 30902dc3cb ("ax25: Fix
std timer socket destroy handling.") we have to put some kind of fix
in to cure the issue whereby unaccepted connections do not get destroyed.
The approach used here is from Tihomir Heidelberg - 9a4gl
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 30902dc3cb.
It causes all kinds of problems, based upon a report by
Bernard (f6bvp) and analysis by Jarek Poplawski.
Signed-off-by: David S. Miller <davem@davemloft.net>
The softlockup watchdog needs to be touched when resuming the from the
kgdb stopped state to avoid the printk that a CPU is stuck if the
debugger was active for longer than the softlockup threshold.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Stress-testing KVM's latest NMI support with kgdbts inside an SMP guest,
I came across spurious unhandled NMIs while running the singlestep test.
Looking closer at the code path each NMI takes when KGDB is enabled, I
noticed that kgdb_nmicallback is called twice per event: One time via
DIE_NMI_IPI notification, the second time on DIE_NMI. Removing the first
invocation cures the unhandled NMIs here.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
qdisc->requeue was planned to universally replace all requeuing code,
but at the top level we never requeue more than one skb, so qdisc->
gso_skb is enough for this. qdisc->requeue would be used on the lower
levels only for one level deep requeuing (like in sch_hfsc) after
finishing all the changes.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
