Moves the x25 interrupt flag from char into bitfield.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the X25 q bit flag from char into a bitfield to allow BKL cleanup.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stop device call netif_carrier_off() just after disabling TX queue to
avoid possibility of netdev watchdog warning and ->ndo_tx_timeout() invocation.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original patch from Stanislaw Gruszka <sgruszka@redhat.com>.
Using netif_carrier_off() is better than updating all the ->trans_start
on all the tx queues.
netif_carrier_off() needs to be called after bnx2_disable_int_sync()
to guarantee no race conditions with the serdes timers that can
modify the carrier state.
If the chip or phy is reset, carrier will turn back on when we get the
link interrupt. If there is no reset, we need to turn carrier back on
in bnx2_netif_start(). Again, the phy_lock prevents race conditions with
the serdes timers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware fixes a performance regression on small packets.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump the correct MCP registers and add EMAC_RX_STATUS register during
NETDEV_WATCHDOG for debugging.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device state need to be mark as FAILED, if fail to start firmware.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing register defines which are not used by Qlgoic CNA device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset/set DEV_UP bit during allocation and deallocation of resources.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default fw is loaded from flash, user can
change this priority using load_fw_file module param.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added lrobytes to it.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Append mac address to adapter name.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes memory leak in error path when memory allocation
for adapter data structures fails.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the platform data for the mii_bus is missing, gracefully error out
rather than deference NULL pointers.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have the low level MDIO functions pass back up timeout information so we
don't waste time polling them multiple times when there is a problem, and
so we don't let higher layers think the device is available when it isn't.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using the Receive All Frames (RAF) bit to enable promiscuous
mode, use the Promiscuous (PR) bit. This lowers overhead at runtime as
we let the hardware process the packets that should actually be checked.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that WOL works only in PM Suspend Standby Mode (Sleep Mode).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we might be get a setting mismatch from a previous module or
bootloader and what the driver currently expects.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP checksum is based on 16-bit one's complement algorithm, so to deduce a
value from checksum is equal to add its complement.
Unfortunately, the Blackfin on-chip MAC checksum logic only works when the
IP packet has a header length of 20 bytes. This is true for most IPv4
packets, but not for IPv6 packets or IPv4 packets which use header options.
So only use the hardware checksum when appropriate.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jon Kowal <jon.kowal@dspecialists.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb buffer isn't actually used until we finish transferring and pass
it up to higher layers, so only invalidate the range once before we start
receiving actual data. This also avoids the problem with data invalidating
on Blackfin systems -- there is no invalidate-only, just invalidate+flush.
So when running in writeback mode, there is the small (but not uncommon)
possibility of the flush overwriting valid DMA-ed data from the cache.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer on-chip MAC peripherals support IEEE 1588 PTP in the hardware, so
extend the driver to support this functionality.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP outgoing packets can avoid two atomic ops, and dirtying
of previously higly contended cache line using new refdst
infrastructure.
Note 1: loopback device excluded because of !IFF_XMIT_DST_RELEASE
Note 2: UDP packets dsts are built before ip_queue_xmit().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ip_route_input_noref() in ip fast path, to avoid two atomic ops per
incoming packet.
Note: loopback is excluded from this optimization in ip_rcv_finish()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_input() is the version returning a refcounted dst, while
ip_route_input_noref() returns a non refcounted one.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use low order bit of skb->_skb_dst to tell dst is not refcounted.
Change _skb_dst to _skb_refdst to make sure all uses are catched.
skb_dst() returns the dst, regardless of noref bit set or not, but
with a lockdep check to make sure a noref dst is not given if current
user is not rcu protected.
New skb_dst_set_noref() helper to set an notrefcounted dst on a skb.
(with lockdep check)
skb_dst_drop() drops a reference only if skb dst was refcounted.
skb_dst_force() helper is used to force a refcount on dst, when skb
is queued and not anymore RCU protected.
Use skb_dst_force() in __sk_add_backlog(), __dev_xmit_skb() if
!IFF_XMIT_DST_RELEASE or skb enqueued on qdisc queue, in
sock_queue_rcv_skb(), in __nf_queue().
Use skb_dst_force() in dev_requeue_skb().
Note: dst_use_noref() still dirties dst, we might transform it
later to do one dirtying per jiffies.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_SMP=y, then we own a queue spinlock, we can avoid the atomic
test_and_set_bit() from napi_schedule_prep().
We now have same number of atomic ops per netif_rx() calls than with
pre-RPS kernel.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using this driver can cause unaligned accesses in the IP layer
This has been fixed by aligning the skb data correctly using the
spare room left over by the 4 byte header inserted between packets
by the device.
Signed-off-by: Neil Jones <NeilJay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for resuming from suspend for IBM virtual ethernet devices.
We may have lost an interrupt over the suspend, so we just kick the
interrupt handler to process anything that is outstanding.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
as addrlabels with an interface index are left alone when the
interface gets removed this results in addrlabels that can no
longer be removed.
Restrict validation of index to adding new addrlabels.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The choice was to either delay creation of the new UUID until
IO got thawed or to delay it until the first IO request.
Both are correct, the later is more friendly to users of
dual-primary setups, that actually only write on one side.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we detect late (= after grabing mdev->req_lock) that IO got frozen, we
return 1 to generic_make_request(), which simply will retry to make a
request for that bio.
In the subsequent call of generic_make_request() into drbd_make_request_26()
we sleep in inc_ap_bio().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now that the peer may handle multi-bio EEs,
we can ignore the peer's limit,
and concentrate on the limits of the local IO stack.
This is safe accross drbd protocol versions,
as our queue_max_sectors() will be adjusted accordingly.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
this should allow for better background resync performance.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This should allow for better performance if the lower level IO stack
of the peers differs in limits exposed either via the queue,
or via some merge_bvec_fn.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There is no need trying to load the (even in most cases) not availible
firmware after suspend. This saves about 30 secounds on reset waiting
for timeout.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds an argument to the DMAengine control function, so that
we can later provide control commands that need some external data
passed in through an argument akin to the ioctl() operation
prototype.
[dan.j.williams@intel.com: fix up some missed conversions]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* Only send delay_probes with protocol 93 or newer
* drbd_send_delay_probes() is called only from worker context,
no atomic_t needed for delay_seq
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* Mention P_DELAY_PROBE in the packet naming array
* Do not corrupt the mdev->data.work list in case the timer goes
off before delay_probe_work got handled by the worker
* Do not mod_timer() twice for a single delay_probe pair
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In a setup with a high bandwidth and high latency network, eventually
involving deep queues in routers, it is beneficial to only fill those
queues up to an limited extend with resync data.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
To reasonably control resync speed over drbd-proxy connections,
drbd has to measure the current delay of packets transmitted over
the (possibly congested) data socket vs the meta-data socket.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
