Depending on the regulator version, the voltage table might be
different. Use version specific regulator tables in order to select
correct voltage table. For the following regulator versions different
voltage tables are now used:
* TPS658623: Use correct voltage table for SM2
* TPS658643: New voltage table for SM2
Both versions are in use on the Colibri T20 module. Make use of the
correct tables by requesting the correct SM2 voltage of 1.8V.
This change is not backward compatible since an old driver is not able
to correctly set that value. The value 1.8V is out of range for the old
driver and will refuse to probe the device. The regulator starts with
default settings and the driver shows appropriate error messages.
On Colibri T20, the old value used to work with TPS658623 since the
driver applied a wrong voltage table too. However, the TPS658643 used
on V1.2 devices uses yet another voltage table and those broke that
pseudo-compatibility. The regulator driver now has the correct voltage
table for both regulator versions and those the correct voltage can be
used in the device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the VERSIONCRC to determine the exact device version. According to
the datasheet this register can be used as device identifier. The
identification is needed since some tps6586x regulators use a different
voltage table.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is the other of the LP3943 MFD driver.
LP3943 can be used as a PWM generator, up to 2 channels.
* Two PWM generators supported
* Supported PWM operations
request, free, config, enable and disable
* Pin assignment
A driver data, 'pin_used' is checked when a PWM is requested.
If the output pin is already assigned, then returns as failure.
If the pin is available, 'pin_used' is set.
When the PWM is not used anymore, then it is cleared.
It is defined as unsigned long type for atomic bit operation APIs,
but only LSB 16bits are used because LP3943 has 16 outputs.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
LP3943 has 16 output pins which can be used as GPIO expander and PWM generator.
* Regmap I2C interface for R/W LP3943 registers
* Atomic operations for output pin assignment
The driver should check whether requested pin is available or not.
If the pin is already used, pin request returns as a failure.
A driver data, 'pin_used' is checked when gpio_request() and
pwm_request() are called. If the pin is available, then pin_used is set.
And it is cleared when gpio_free() and pwm_free().
* Device tree support
Compatible strings for GPIO and PWM driver.
LP3943 platform data is PWM related, so parsing the device tree is
implemented in the PWM driver.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is one of LP3943 MFD driver.
LP3943 is configurable as a GPIO expander, up to 16 GPIOs.
* Application note: how to configure LP3943 as a GPIO expander
http://www.ti.com/lit/an/snva287a/snva287a.pdf
* Supported GPIO controller operations
request, free, direction_input, direction_output, get and set
* GPIO direction register not supported
LP3943 doesn't have the GPIO direction register. It only provides input and
output status registers.
So, private data for the direction should be handled manually.
This variable is updated whenever the direction is changed and
used in 'get' operation.
* Pin assignment
A driver data, 'pin_used' is checked when a GPIO is requested.
If the GPIO is already assigned, then returns as failure.
If the GPIO is available, 'pin_used' is set.
When the GPIO is not used anymore, then it is cleared.
It is defined as unsigned long type for atomic bit operation APIs,
but only LSB 16bits are used because LP3943 has 16 outputs.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Bindings for LP3943 MFD, GPIO and PWM controller are added.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
"pdata" is a NULL not an ERR_PTR so there is no use printing it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This helps move us towards removing the bus custom operations.
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All subdrivers use the irqdomain to demux AB8500 IRQs but here
in the hierarchical path we find a leftover instance using the
hard-coded IRQ base. Convert it to use irqdomain with a
oneliner.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
drivers/mfd/rtl8411.c: In function 'rtl8411_fetch_vendor_settings':
drivers/mfd/rtl8411.c:58:7: warning: 'reg1' is used uninitialized in this function [-Wuninitialized]
drivers/mfd/rtl8411.c: In function 'rtl8411b_fetch_vendor_settings':
drivers/mfd/rtl8411.c:79:7: warning: 'reg' is used uninitialized in this function [-Wuninitialized]
drivers/mfd/rtl8411.c: In function 'rtl8411_fetch_vendor_settings':
drivers/mfd/rtl8411.c:69:26: warning: 'reg3' may be used uninitialized in this function [-Wuninitialized]
Tested-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This deletes the special AB8500 GPIO platform data passing
header and merges the few remaining contents down into the
abx500 pinctrl driver which handles the abx500 GPIO device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This deletes all instances where the AB8500 GPIO platform
data is passed around. It is completely unused in the kernel
now, so it does not hurt anyone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All instances of this device are now coming from device tree-
enabled platforms probing without using platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since we still need to rely on a mix of device tree initialized
drivers and legacy platform data initialize drivers, let's fix
the passing of platform data to twl4030-gpio.
As the twl4030 GPIO is initialized by twl-core.c, we need to register
the auxdata for twl4030 GPIO in twl-core.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since currently nobody uses TWL603x platform data and all new
users will supply it through device tree, handling of these
data within twl-core will never be used, so remove it.
Signed-off-by: Ruslan Ruslichenko <ruslan.ruslichenko@globallogic.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add "const" to "static struct regmap_irq" and "static struct
regmap_config".
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Match max14577 regulator driver by of_compatible specified in mfd_cell.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds max14577 core/irq driver to support MUIC(Micro USB IC)
device and charger device and support irq domain method to control
internal interrupt of max14577 device. Also, this patch supports DT
binding with max14577_i2c_parse_dt().
The MAXIM 14577 chip contains Micro-USB Interface Circuit and Li+ Battery
Charger. It contains accessory and USB charger detection logic. It supports
USB 2.0 Hi-Speed, UART and stereo audio signals over Micro-USB connector.
The battery charger is compliant with the USB Battery Charging Specification
Revision 1.1. It has also SFOUT LDO output for powering USB devices.
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add PM suspend/resume ops to the sec MFD core driver and make it a wake
up source. This allows proper waking from suspend to RAM and also fixes
broken interrupts after resuming:
[ 42.705703] sec_pmic 7-0066: Failed to read IRQ status: -5
Interrupts stop working after first resume initiated by them (e.g. by
RTC Alarm interrupt) because interrupt registers were not cleared properly.
When device is woken up from suspend by RTC Alarm, an interrupt occurs
before resuming I2C bus controller. The interrupt is handled by
regmap_irq_thread which tries to read RTC registers. This read fails
(I2C is still suspended) and RTC Alarm interrupt is disabled.
Disable the S5M8767 interrupts during suspend (disable_irq()) and enable
them during resume so the device will be still woken up but the interrupt
won't happen before resuming I2C bus.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rename cros_ec_{probe,remove}_i2c() to cros_ec_i2c_{probe,remove}() for
consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rename cros_ec_{probe,remove}_spi() to cros_ec_spi_{probe,remove}() for
consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
_fdt_start is an array, i.e. a pointer.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Without this, "make defconfig" fails with
*** Can't find default configuration "arch/microblaze/defconfig"!
All other architectures either set KBUILD_DEFCONFIG, or provide
arch/*/defconfig.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the naming scheme 'devicename:colour' for the Dualshock 4
LED lightbar controls as specified in Documentation/leds/leds-class.txt
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
cache_chain_mutex has been replaced by slab_mutex. Fix this remaining
outdated comment.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some inodes in readdir reply may have no caps. Getattr mds request
for these inodes can return -ESTALE. The fix is consider dentry that
links to inode with no caps as invalid. Invalid dentry causes a
lookup request to send to the mds, the MDS will send caps back.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Send requests that operate on path to directory's auth MDS if
mode == USE_AUTH_MDS. Always retry using the auth MDS if got
-ESTALE reply from non-auth MDS. Also clean up the code that
handles auth MDS change.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
- don't trim auth cap if there are flusing caps
- don't trim auth cap if any 'write' cap is wanted
- allow trimming non-auth cap even if the inode is dirty
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
handle following sequence of events:
- non-auth MDS revokes Fc cap. queue invalidate work
- auth MDS issues Fc cap through request reply. i_rdcache_gen gets
increased.
- invalidate work runs. it finds i_rdcache_revoking != i_rdcache_gen,
so it does nothing.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
features->quirks can have multiple bits set. For dual input, we only
need to check WACOM_QUIRK_MULTI_INPUT.
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Simplify the error path and remove() function by using devm_*
functions for requesting gpios and irq and allocating the input
device.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
New tree with the INFO ioctl merge fixed up. This also adds a couple
of additional minor fixes.
A few more changes for 3.14, mostly just bug fixes. Note that:
drm/radeon: add query to fetch the max engine clock.
will conflict with 3.13 final, but the fix is pretty obvious.
* 'drm-next-3.14' of git://people.freedesktop.org/~agd5f/linux: (22 commits)
drm/radeon: add UVD support for OLAND
drm/radeon: fix minor typos in si_dpm.c
drm/radeon: set the full cache bit for fences on r7xx+
drm/radeon: fix surface sync in fence on cayman (v2)
drm/radeon/dpm: disable mclk switching on desktop RV770
drm/radeon: fix endian handling in radeon_atom_init_mc_reg_table
drm/radeon: write gfx pg bases even when gfx pg is disabled
drm/radeon: bail early from enable ss in certain cases
drm/radeon: handle ss percentage divider properly
drm/radeon: add query to fetch the max engine clock (v2)
drm/radeon/dp: sleep after powering up the display
drm/radeon/dp: use usleep_range rather than udelay
drm/radeon/dp: bump i2c-over-aux retries to 7
drm/radeon: disable ss on DP for DCE3.x
drm/radeon/cik: use hw defaults for TC_CFG registers
drm/radeon: disable dpm on BTC
drm/radeon/cik: use WAIT_REG_MEM special op for CP HDP flush
drm/radeon/cik: use POLL_REG_MEM special op for sDMA HDP flush
drm/radeon: consolidate sdma hdp flushing code for CIK
drm/radeon: consolidate cp hdp flushing code for CIK
...
Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of people.)
USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdjwIACgkQMUfUDdst+ylBIQCgkRoR8lJc0L5lZ3fugIJL4IzZ
j6AAn0nBLP6VI0cvUEi3TcrPTzv4MEuL
=Yb+I
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of
people). USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues"
* tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (318 commits)
usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX
usb: chipidea: need to mask INT_STATUS when write otgsc
usb: chipidea: put hw_phymode_configure before ci_usb_phy_init
usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flag
usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28
usb: chipidea: add freescale imx28 special write register method
usb: ehci: add freescale imx28 special write register method
usb: core: check for valid id_table when using the RefId feature
usb: cdc-wdm: resp_count can be 0 even if WDM_READ is set
usb: core: bail out if user gives an unknown RefId when using new_id
usb: core: allow a reference device for new_id
usb: core: add sanity checks when using bInterfaceClass with new_id
USB: image: correct spelling mistake in comment
USB: c67x00: correct spelling mistakes in comments
usb: delete non-required instances of include <linux/init.h>
usb:hub set hub->change_bits when over-current happens
Revert "usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28"
xhci: Set scatter-gather limit to avoid failed block writes.
xhci: Avoid infinite loop when sg urb requires too many trbs
usb: gadget: remove unused variable in gr_queue_int()
...
Here's the big tty/serial driver pull request for 3.14-rc1
There are a number of n_tty fixes and cleanups, and some serial driver
bugfixes, and we got rid of one obsolete driver, making this series
remove more lines than added, always a nice surprise.
All of these have been in linux-next with no reports of issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdiiAACgkQMUfUDdst+ymInACgu+gjm0q6sua8Zsk9HN3Ko0jK
Zy0AoI7jieqSxZfvZD84US98HTiWtumH
=z6GV
-----END PGP SIGNATURE-----
Merge tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver pull request for 3.14-rc1
There are a number of n_tty fixes and cleanups, and some serial driver
bugfixes, and we got rid of one obsolete driver, making this series
remove more lines than added, always a nice surprise.
All of these have been in linux-next with no reports of issues"
* tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (60 commits)
tty/serial: at91: disable uart timer at start of shutdown
serial: 8250: enable UART_BUG_NOMSR for Tegra
tty/serial: at91: reset rx_ring when port is shutdown
tty/serial: at91: fix race condition in atmel_serial_remove
tty/serial: at91: Handle shutdown more safely
serial: sirf: correct condition for fetching dma buffer into tty
serial: sirf: provide pm entries of uart_ops
serial: sirf: use PM macro initialize PM functions
serial: clps711x: Enable driver compilation with COMPILE_TEST
serial: clps711x: Add support for N_IRDA line discipline
tty: synclink: avoid sleep_on race
tty/amiserial: avoid interruptible_sleep_on
tty: delete non-required instances of include <linux/init.h>
tty: an overflow of multiplication in drivers/tty/cyclades.c
serial: Remove old SC26XX driver
serial: add support for 200 v3 series Titan card
serial: 8250: Fix initialisation of Quatech cards with the AMCC PCI chip
tty: Removing the deprecated function tty_vhangup_locked()
TTY/n_gsm: Removing the wrong tty_unlock/lock() in gsm_dlci_release()
tty/serial: at91: document clock properties
...
Here's the big drivers/staging/ update for 3.14-rc1
Lots and lots of cleanups, IIO driver updates are also mixed in here due
to the subsystem still crossing staging and drivers/iio/, and the dwc2
driver is moved out of staging. There's a new driver (rts5208), which
ends up making us adding more lines than removing, but overall there was
lots of work toward moving code out of here, which was good.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdiE8ACgkQMUfUDdst+ynmYgCcDI9d1Jjo42+tpilIl3hOEb/f
sF8An1W3HRXM3XPG+X1POqprMAk0Jt63
=1Ztu
-----END PGP SIGNATURE-----
Merge tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver tree changes from Greg KH:
"Here's the big drivers/staging/ update for 3.14-rc1
Lots and lots of cleanups, IIO driver updates are also mixed in here
due to the subsystem still crossing staging and drivers/iio/, and the
dwc2 driver is moved out of staging. There's a new driver (rts5208),
which ends up making us adding more lines than removing, but overall
there was lots of work toward moving code out of here, which was good
All of this has been in linux-next with no reported issues"
* tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1084 commits)
lustre: delete linux/lustre_debug.h
staging: lustre: remove some unused debug macros
usb: dwc2: move device tree bindings doc to correct place
staging: vt6656: sparse fixes: iwctl_giwgenie use memcpy.
staging: vt6656: sparse fixes: iwctl_siwgenie use memcpy.
staging: vt6656: sparse fixes ethtool_ioctl Use struct ifreq *
staging: vt6656: sparse fixes: dpc.c missing dpc.h
staging: lustre: libcfs_debug: small whitespace cleanups
staging: lustre: libcfs_debug.h: remove extra blank lines
staging: lustre: libcfs_debug.h: Align backslashes in macros
staging: lustre: libcfs_debug.h: align define values
staging: tidspbridge: adjust error return code (bugfix)
Staging: rts5139: rts51x_card: fixed style issues
staging: wlags49_h2: Fix "do not use C99 //" in wl_cs.h, wl_enc.h wl_main.h and wl_wext.h
Staging: rtl8188eu: Fixed "foo * bar" related coding style issues
Staging: rtl8188eu: Fixed required spaces after ',' and around '=' and '=='
staging: vt6655: Fix memory leak in wpa_ioctl()
imx-drm: parallel-display: honor 'native-mode' property when selecting video mode from DT
staging: drm/imx: don't drop crtc offsets when doing pageflip
staging: drm/imx: handle framebuffer offsets correctly
...
Here's the big driver core and sysfs patch set for 3.14-rc1.
There's a lot of work here moving sysfs logic out into a "kernfs" to
allow other subsystems to also have a virtual filesystem with the same
attributes of sysfs (handle device disconnect, dynamic creation /
removal as needed / unneeded, etc. This is primarily being done for
the cgroups filesystem, but the goal is to also move debugfs to it when
it is ready, solving all of the known issues in that filesystem as well.
The code isn't completed yet, but all should be stable now (there is a
big section that was reverted due to problems found when testing.)
There's also some other smaller fixes, and a driver core addition that
allows for a "collection" of objects, that the DRM people will be using
soon (it's in this tree to make merges after -rc1 easier.)
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdh0cACgkQMUfUDdst+ylv4QCfeDKDgLo4LsaBIIrFSxLoH/c7
UUsAoMPRwA0h8wy+BQcJAg4H4J4maKj3
=0pc0
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / sysfs patches from Greg KH:
"Here's the big driver core and sysfs patch set for 3.14-rc1.
There's a lot of work here moving sysfs logic out into a "kernfs" to
allow other subsystems to also have a virtual filesystem with the same
attributes of sysfs (handle device disconnect, dynamic creation /
removal as needed / unneeded, etc)
This is primarily being done for the cgroups filesystem, but the goal
is to also move debugfs to it when it is ready, solving all of the
known issues in that filesystem as well. The code isn't completed
yet, but all should be stable now (there is a big section that was
reverted due to problems found when testing)
There's also some other smaller fixes, and a driver core addition that
allows for a "collection" of objects, that the DRM people will be
using soon (it's in this tree to make merges after -rc1 easier)
All of this has been in linux-next with no reported issues"
* tag 'driver-core-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (113 commits)
kernfs: associate a new kernfs_node with its parent on creation
kernfs: add struct dentry declaration in kernfs.h
kernfs: fix get_active failure handling in kernfs_seq_*()
Revert "kernfs: fix get_active failure handling in kernfs_seq_*()"
Revert "kernfs: replace kernfs_node->u.completion with kernfs_root->deactivate_waitq"
Revert "kernfs: remove KERNFS_ACTIVE_REF and add kernfs_lockdep()"
Revert "kernfs: remove KERNFS_REMOVED"
Revert "kernfs: restructure removal path to fix possible premature return"
Revert "kernfs: invoke kernfs_unmap_bin_file() directly from __kernfs_remove()"
Revert "kernfs: remove kernfs_addrm_cxt"
Revert "kernfs: make kernfs_get_active() block if the node is deactivated but not removed"
Revert "kernfs: implement kernfs_{de|re}activate[_self]()"
Revert "kernfs, sysfs, driver-core: implement kernfs_remove_self() and its wrappers"
Revert "pci: use device_remove_file_self() instead of device_schedule_callback()"
Revert "scsi: use device_remove_file_self() instead of device_schedule_callback()"
Revert "s390: use device_remove_file_self() instead of device_schedule_callback()"
Revert "sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()"
Revert "kernfs: remove unnecessary NULL check in __kernfs_remove()"
kernfs: remove unnecessary NULL check in __kernfs_remove()
drivers/base: provide an infrastructure for componentised subsystems
...
Here's the big char/misc driver patches for 3.14-rc1.
Lots of little things, and a new "big" driver, genwqe. Full details are
in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdgc8ACgkQMUfUDdst+ynt9ACguAhrO2WlowdcUZELadTEpqLX
gbkAn0+c1rjizVdIRvs83aQRNJP6w1uR
=oPmD
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver patches for 3.14-rc1.
Lots of little things, and a new "big" driver, genwqe. Full details
are in the shortlog"
* tag 'char-misc-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
mei: limit the number of consecutive resets
mei: revamp mei reset state machine
drivers/char: don't use module_init in non-modular ttyprintk.c
VMCI: fix error handling path when registering guest driver
extcon: gpio: Add power resume support
Documentation: HOWTO: Updates on subsystem trees, patchwork, -next (vs. -mm) in ko_KR
Documentation: HOWTO: update for 2.6.x -> 3.x versioning in ko_KR
Documentation: HOWTO: update stable address in ko_KR
Documentation: HOWTO: update LXR web link in ko_KR
char: nwbutton: open-code interruptible_sleep_on
mei: fix syntax in comments and debug output
mei: nfc: mei_nfc_free has to be called under lock
mei: use hbm idle state to prevent spurious resets
mei: do not run reset flow from the interrupt thread
misc: genwqe: fix return value check in genwqe_device_create()
GenWQE: Fix warnings for sparc
GenWQE: Fix compile problems for Alpha
Documentation/misc-devices/mei/mei-amt-version.c: remove unneeded call of mei_deinit()
GenWQE: Rework return code for flash-update ioctl
sgi-xp: open-code interruptible_sleep_on_timeout
...
