Enhance the dvb-pll definition of the fmd1216 tuner by adding an init sequence
and a sleep sequence.
The init sequence sets the AGC control register to 0xa0, selecting the fast
time constant and 112 dBuV take-over point. This the recommended value for
DVB-T operation.
The sleep sequence sets bit P4 (which is believed to turn the analog
demodulator on), turns off the tuning voltage, and sets the AGC control
register to 0x60 (external AGC voltage, the recommended value for analog
operation).
The existing dvb-pll users in the cx88 driver, listed below, will gain these
init and sleep sequences.
CX88_BOARD_HAUPPAUGE_HVR1100 Hauppauge WinTV-HVR1100 DVB-T/Hybrid
CX88_BOARD_HAUPPAUGE_HVR1100LP Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profi
CX88_BOARD_WINFAST_DTV2000H WinFast DTV2000 H
CX88_BOARD_HAUPPAUGE_HVR3000 Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DV
CX88_BOARD_HAUPPAUGE_HVR1300 Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encod
This non-dvb-pll user in the cx88 driver should only gain the sleep sequence,
as it already had an equivalent init sequence. The non-dvb-pll code for this
user is removed.
X88_BOARD_DNTV_LIVE_DVB_T_PRO digitalnow DNTV Live! DVB-T Pro
In these saa7134 driver, these non-dvb-pll users are converted to use dvb-pll:
SAA7134_BOARD_MD7134 Medion 7134
SAA7134_BOARD_ASUS_EUROPA2_HYBRID Asus Europa2 OEM
The saa7134 functions philips_fmd1216_tuner_init(),
philips_fmd1216_tuner_sleep(), and philips_fmd1216_tuner_set_params() are
deleted and the dvb-pll versions are used.
This should result in equivalent sleep, init, and tuning sequences being sent
to the tuner.
For the cxusb driver, only one board is effected:
USB_PID_MEDION_MD95700 Medion MD95700
This board used dvb_usb_tuner_init_i2c() and dvb_usb_tuner_set_params_i2c()
for init and tuning, respectively. These functions are effectively the same
as the dvb-pll versions. They call a tuner pass control function defined at
the dvb-usb level, but this does not matter, as this card does not have a
tuner pass control function (only the dib3000mb does). This board will gain
the sleep sequence, while init and tuning should be unchanged.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support for A-LINK DTU(m) is not included in this patch.
Signed-off-by: Aapo Tahkola <aet@rasterburn.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Marked af9005 driver as experimental and add dependency for qt1010;
Added a dependency on qt1010 in Kconfig;
Corrected the experimental gain reduction of the mt2060 in case of
strong signal (though it is code included in #ifdef 0).
Signed-off-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
convert calls to dib3000mb_attach to use dvb_attach
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
moved tda665x pll_init into dvb_pll_desc dvb_pll_tda665x.initdata
convert handling of tda665x and tua6010xs to properly use dvb-pll
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These sources do not need to #include "dvb-pll.h"
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Using Encore's key codes, we needn't add any additional key table.
Signed-off-by: Tony Wan <wankai@sjtu.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support the 10moons TM300 TV card (so called TV Master 3), which is a
10moons saa7130 based board. Here not include features for the
IR-remote.
It has been tested using TVTIME. The card was auto-detected and all the
input sources worked correct with sound.
Signed-off-by: Tony Wan <wankai@sjtu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ioctl entry point, a big switch/case, is splitted in little
functions.
These functions are set as callbacks for the video_ioctl2 video4linux
facility.
This improves the driver memory consumption and enables the v4l1
compatibility as a side effect.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Acked-by: Dwaine P. Garden <dwainegarden@rogers.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Radio and video ioctls are the same,
delete the usbvision_do_radio_ioctl function
add the special cases for radio in usbvision_v4l2_do_ioctl
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
usbvision_set_video_format: add comment that VO_MODE is also being set.
Signed-off-by: David Warman <dwarman@davidwarman.net>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes duplicate code from cx88-dvb and saa7134-dvb that handles
rf input switching for the TUV1236d tuner.
The functionality is added to dvb-pll, where all the other code that
handles the TUV1236d is kept.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename dvb_pll_desc.setbw() to set(), and accept struct dvb_frontend_parameters
instead of passing both freq and bandwidth, so that this may be used as a
generic function.
In order to do this, dvb_pll_configure must also be altered in the same manner,
to take struct dvb_frontend_parameters instead of freq and bandwidth.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All the printks had missing level prefixes so I've fixed these too.
Also fixed some grammer errors.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If cx88 support is compiled into the kernel while vp3054 is left as a module,
the kernel will fail to link. Adjust the existing "#if" code in cx88 so
that it won't consider vp3054 to be supported in this case.
It might make sense to move vp3054 selection into the "customisation" menu
instead of a cx88 sub-option (though this is a cx88 feature, there is no extra
chip involved).
It might also make sense to use dvb_attach() to load vp3054 support.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Get rid of two 'warning: Using plain integer as NULL pointer'.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Memory allocated with kmalloc is always initialzed to 0 with memset.
Replace the two calls with kzalloc, that already does both steps.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for SAS Management Protocol (SMP) passthrough
support via bsg. aic94xx can use this.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The sas transport class attaches one bsg device to every SAS object
(host, device, expander, etc). LLDs can define a function to handle
SMP requests via sas_function_template::smp_handler.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix drivers misusing dev_to_shost
Some drivers were using dev_to_shost to go from a struct device to the
corresponding shost. Unfortunately, dev_to_shost only looks up the tree
to find an shost (it's designed to go from a scsi_device or a
scsi_target to the parent scsi_host), and these drivers were calling it
with the parent of the scsi_host.
I've fixed this by saving a pointer to the Scsi_Host in the drvdata,
which matches what most scsi drivers do.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Report VPD inquiry page 0x80 with an unique array creation serial
number (CUID). When an array is created, the metadata stored on the
physical drives gets an unique serial number. This serial number
remains constant through array morphing or migration to other
controllers. This patch is a forward port and modification to survive
morphing and migration operations, of a similar piece of
(un-attributed author) code added to the SLES10 SP1 aacraid driver.
To test the results of the patch, observe that /dev/disk/by-id/
entries will show up for the arrays resulting from the udev rules.
Also, as per the udev rules, 'scsi_id -g -x -a -s /block/sd? -d
/dev/sd?' will report the ID_SERIAL as constructed from the inquiry
data.
It was reported to me that the 'ADPT' leading the serial number was bad
form, that the inquiry vendor field was enough to differentiate the
storage uniquely. Subsequent search found that another Adaptec AAC based
driver reported the 8 hex serial number only without such adornments, so
dropped ADPT to match. Resubmitting the patch with this alteration.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Incorrect dma mask was used for blinkled (firmware assert) recovery or
user initiated reset during initialization portion. Ensure that all
callers of aac_fib_map_free null out the fib allocation references to
prevent multiple free. Although serious sounding, no reports of these
problems have surfaced...
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
During an Adapter Initiated scan request, the query disk ioctl reports a
value of 2 rather than 1 for the valid field. This presents a problem
for some legacy management applications.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for Brocade 410/420 4Gbit FC HBAs.
They are re-branded LSI HBAs [LSI7104EP-LC/LSI7204EP-LC]
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The mptspi and mptsas drivers are modified to deregister from transport layer
if registration with PCI driver failed
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New sysfs scsi_host attributes are added to provide information about Firmware
version, BIOS version, MPI version and other product related information
signed-off-by: Sathya Praksh <sathya.prakash@lsi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
so that the user can disable all the options in that menu at once
instead of having to disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
seagate_st0x_detect() can become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- #include <asm/irq.h> for getting the prototypes of {dis,en}able_irq()
- make the needlessly global wd33c93_setup() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains the following cleanups:
- make needlessly global functions static
- every file should #include the headers containing the prototypes for
it's global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
lockdep noticed that with ATA support the port->dev_list_lock was
entangled at irq context, so it now needs to become IRQ safe
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This one was noticed by Gilbert Wu of Adaptec:
The libata core actually does the DMA mapping for you, so there has to
be an exception in the device drivers that *don't* do dma mapping for
ATA commands. However, since we've already done this, libsas must now
dma map any ATA commands that it wishes to issue ... and yes, this is a
horrible mess.
Additionally, the test in aic94xx for ATA protocols isn't quite right.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ATA devices need special handling for sas_task_abort. If the ATA command
came from SCSI, then we merely need to tell SCSI to abort the scsi_cmnd.
However, internal commands require a bit more work--we need to fill the qc
with the appropriate error status and complete the command, and eventually
post_internal will issue the actual ABORT TASK.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SATL should connect the scsi_cmnd to the sas_task (despite the presence
of libata) so that requests to abort scsi_cmnds headed to the ATA device
can be processed by the EH and aborted correctly. The abort status should
still be propagated from sas -> ata -> scsi.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When libsas encounters a STP device whose protocol isn't recognized (i.e.
not ATA or ATAPI), we should set the ata_device's class to ATA_DEV_UNKNOWN
instead of ATA_DEV_ATA.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A sas_task sent to an ATAPI devices returns SAM_GOOD if successful.
Therefore, we should treat this the same way we treat ATA commands
that succeed.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since the aic94xx sequencer assigns its own NCQ tags to ATA commands, it
no longer makes any sense to copy the sactive field in the STP response
to ata_port->sactive, as that will confuse libata. Also, libata seems
to be capable of managing sactive on its own.
The attached patch gets rid of one of the causes of the BUG messages in
ata_qc_new, and seems to work without problems on an IBM x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds a new field, lldd_task, to ata_queued_cmd so that libata
users such as libsas can associate some data with a qc. The particular
ambition with this patch is to associate a sas_task with a qc; that way,
if libata decides to timeout a command, we can come back (in
sas_ata_post_internal) and abort the sas task.
One question remains: Is it necessary to reset the phy on error, or will
the libata error handler take care of it? (Assuming that one is written,
of course.) This patch, as it is today, works well enough to clean
things up when an ATA device probe attempt fails halfway through the probe,
though I'm not sure this is always the right thing to do.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The sas_ata_qc_issue function was incorrectly written to return error
codes such as -ENOMEM. Since libata OR's qc->err_mask with the
return value, It is necessary to make my code return one of the
AC_ERR_ codes instead. For now, use AC_ERR_SYSTEM because an error
here means that the OS couldn't send the command to the controller.
If anybody has a suggestion for a better AC_ERR_ code to use, please
suggest it.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ata_qc_complete and ata_sas_queuecmd require that the port lock be held
when they are called. sas_ata doesn't do this, leading to BUG messages
about qc tags newly allocated qc tags already being in use. This patch
fixes the locking, which should clean up the rest of those messages.
So far I've tested this against an IBM x206m with two SATA disks with no
BUG messages and no other signs of things going wrong, and the machine
finally passed the pounder stress test.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It turns out that libata has already dma_map_sg'd the scatterlist
entries that go with an ata_queued_cmd by the time it calls
sas_ata_qc_issue. sas_ata_qc_issue passes this scatterlist to aic94xx.
Unfortunately, aic94xx assumes that any scatterlist passed to it needs
to be pci_map_sg'd... which blows away the mapping that libata created!
This causes (on a x260) Calgary IOMMU table leaks and duplicate frees
when aic94xx and libata try to {pci,dma}_unmap_sg the scatterlist.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Key this check off ATA_PROTOCOL_STP
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>