We need to set cpsr before determining the spsr bank, as the bank
depends on the target exception level of the injection, not the
current mode of the vcpu. Normally this is one in the same (EL1),
but not when we manage to trap an EL0 fault. It still doesn't really
matter for the 64-bit EL0 case though, as vcpu_spsr() unconditionally
uses the EL1 bank for that. However the 32-bit EL0 case gets fun, as
that path will lead to the BUG() in vcpu_spsr32().
This patch fixes the assignment order and also modifies some white
space in order to better group pairs of lines that have strict order.
Cc: stable@vger.kernel.org # v4.5
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
commit 3c8f7710c1 ("ASoC: fix broken pxa SoC support") has removed
the SND_ARM dependency from SND_PXA2XX_LIB and SND_PXA2XX_LIB_AC97,
by moving these config entries outside of the "if SND_ARM ... endif"
construct.
However, by placing these 2 symbols right between the SND_ARM
menuconfig definition and the first SND_ARM menu entry, the side
effect is that the SND_ARM menu becomes empty and all the config
entries caught between "if SND_ARM ... endif" no more belong to
menuconfig SND_ARM, but to its parent (menuconfig SND).
Fix this.
Signed-off-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As reported by Zijun, the fdt_check_header() call in __fixmap_remap_fdt()
is not safe since it is not guaranteed that the FDT header is mapped
completely. Due to the minimum alignment of 8 bytes, the only fields we
can assume to be mapped are 'magic' and 'totalsize'.
Since the OF layer is in charge of validating the FDT image, and we are
only interested in making reasonably sure that the size field contains
a meaningful value, replace the fdt_check_header() call with an explicit
comparison of the magic field's value against the expected value.
Cc: <stable@vger.kernel.org>
Reported-by: Zijun Hu <zijun_hu@htc.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Kexec needs to know the addresses of all VMCSs that are active on
each CPU, so that it can flush them from the VMCS caches. It is
safe to record superfluous addresses that are not associated with
an active VMCS, but it is not safe to omit an address associated
with an active VMCS.
After a call to vmcs_load, the VMCS that was loaded is active on
the CPU. The VMCS should be added to the CPU's list of active
VMCSs before it is loaded.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
KVM maintains L1's current VMCS in guest memory, at the guest physical
page identified by the argument to VMPTRLD. This makes hairy
time-of-check to time-of-use bugs possible,as VCPUs can be writing
the the VMCS page in memory while KVM is emulating VMLAUNCH and
VMRESUME.
The spec documents that writing to the VMCS page while it is loaded is
"undefined". Therefore it is reasonable to load the entire VMCS into
an internal cache during VMPTRLD and ignore writes to the VMCS page
-- the guest should be using VMREAD and VMWRITE to access the current
VMCS.
To adhere to the spec, KVM should flush the current VMCS during VMPTRLD,
and the target VMCS during VMCLEAR (as given by the operand to VMCLEAR).
Since this implementation of VMCS caching only maintains the the current
VMCS, VMCLEAR will only do a flush if the operand to VMCLEAR is the
current VMCS pointer.
KVM will also flush during VMXOFF, which is not mandated by the spec,
but also not in conflict with the spec.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is known that PMU isn't working in some virtualized environments.
Modify the message issued in that case to mention why hardware PMU
isn't usable instead of reporting it to be broken.
As a side effect this will correct a little bug in the error message:
The error message was meant to be either of level err or info
depending on the environment (native or virtualized). As the level is
taken from the format string and not the printed string, specifying
it via %s and a conditional argument didn't work the way intended.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Link: http://lkml.kernel.org/r/1470051427-16795-1-git-send-email-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Add support for an enable regulator to lp855x_bl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=rUNA
-----END PGP SIGNATURE-----
Merge tag 'backlight-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Add support for an enable regulator to lp855x_bl"
* tag 'backlight-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: lp855x: Add enable regulator
- New API to call bespoke pre/post IRQ handlers; Regmap
- New Device Support
- Add support for RN5T567 to rn5t618
- Add support for COMe-cSL6 and COMe-mAL10 to kempld-core
- New Functionality
- Add support for USB Power Supply to axp20x
- Add support for Power Key to hi655x-pmic
- Fix-ups
- Update MAINTAINERS; Dialog, Altera
- Remove module support; max77843, max77620, max8998, max8997, max8925-i2c
- Add module support; max14577
- Constifying; max77620
- Allow bespoke IRQ masking/unmasking; max77620
- Remove superfluous code; arizona, qcom_rpm, smsc-ece1099
- Power Management fixups; arizona-core
- Error-path improvement; twl-core, dm355evm_msp, smsc-ece1099, hi655x
- Clocking fixups; twl6040
- Trivial (spelling, headers, coding-style, whitespace, (re)naming);
si476x-i2c, omap-usb-tll, ti_am335x_tscadc, tps6507, hi655x-pmic
- Bug Fixes
- Fix offset error for MSM8660; qcom_rpm
- Fix possible spurious IRQs; arizona, hi655x-pmic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=KB2d
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- New API to call bespoke pre/post IRQ handlers; Regmap
New Device Support:
- Add support for RN5T567 to rn5t618
- Add support for COMe-cSL6 and COMe-mAL10 to kempld-core
New Functionality:
- Add support for USB Power Supply to axp20x
- Add support for Power Key to hi655x-pmic
Fix-ups:
- Update MAINTAINERS; Dialog, Altera
- Remove module support; max77843, max77620, max8998, max8997, max8925-i2c
- Add module support; max14577
- Constifying; max77620
- Allow bespoke IRQ masking/unmasking; max77620
- Remove superfluous code; arizona, qcom_rpm, smsc-ece1099
- Power Management fixups; arizona-core
- Error-path improvement; twl-core, dm355evm_msp, smsc-ece1099, hi655x
- Clocking fixups; twl6040
- Trivial (spelling, headers, coding-style, whitespace, (re)naming);
si476x-i2c, omap-usb-tll, ti_am335x_tscadc, tps6507, hi655x-pmic
Bug Fixes:
- Fix offset error for MSM8660; qcom_rpm
- Fix possible spurious IRQs; arizona, hi655x-pmic"
* tag 'mfd-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (42 commits)
mfd: qcom_rpm: Parametrize also ack selector size
mfd: twl6040: Handle mclk used for HPPLL and optional internal clock source
mfd: Add support for COMe-cSL6 and COMe-mAL10 to Kontron PLD driver
mfd: hi655x: Fix return value check in hi655x_pmic_probe()
mfd: smsc-ece1099: Return directly after a function failure in smsc_i2c_probe()
mfd: smsc-ece1099: Delete an unnecessary variable initialisation in smsc_i2c_probe()
mfd: dm355evm_msp: Return directly after a failed platform_device_alloc() in add_child()
mfd: twl-core: Refactoring for add_numbered_child()
mfd: twl-core: Return directly after a failed platform_device_alloc() in add_numbered_child()
mfd: arizona: Add missing disable of PM runtime on probe error path
mfd: stmpe: Move platform data into MFD driver
mfd: max14577: Allow driver to be built as a module
mfd: max14577: Use module_init() instead of subsys_initcall()
mfd: arizona: Remove some duplicate defines
mfd: qcom_rpm: Remove unused define
mfd: hi655x-pmic: Add powerkey device to hi655x PMIC driver
mfd: hi655x-pmic: Rename some interrupt macro names
mfd: hi655x-pmic: Fixup issue with un-acked interrupts
mfd: arizona: Check if AOD interrupts are pending before dispatching
mfd: qcom_rpm: Fix offset error for msm8660
...
In the updates:
* Big endian support and preparation for defered probing for the
Exynos IOMMU driver
* Simplifications in iommu-group id handling
* Support for Mediatek generation one IOMMU hardware
* Conversion of the AMD IOMMU driver to use the generic IOVA
allocator. This driver now also benefits from the recent
scalability improvements in the IOVA code.
* Preparations to use generic DMA mapping code in the Rockchip
IOMMU driver
* Device tree adaption and conversion to use generic page-table
code for the MSM IOMMU driver
* An iova_to_phys optimization in the ARM-SMMU driver to greatly
improve page-table teardown performance with VFIO
* Various other small fixes and conversions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xiS2
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- big-endian support and preparation for defered probing for the Exynos
IOMMU driver
- simplifications in iommu-group id handling
- support for Mediatek generation one IOMMU hardware
- conversion of the AMD IOMMU driver to use the generic IOVA allocator.
This driver now also benefits from the recent scalability
improvements in the IOVA code.
- preparations to use generic DMA mapping code in the Rockchip IOMMU
driver
- device tree adaption and conversion to use generic page-table code
for the MSM IOMMU driver
- an iova_to_phys optimization in the ARM-SMMU driver to greatly
improve page-table teardown performance with VFIO
- various other small fixes and conversions
* tag 'iommu-updates-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (59 commits)
iommu/amd: Initialize dma-ops domains with 3-level page-table
iommu/amd: Update Alias-DTE in update_device_table()
iommu/vt-d: Return error code in domain_context_mapping_one()
iommu/amd: Use container_of to get dma_ops_domain
iommu/amd: Flush iova queue before releasing dma_ops_domain
iommu/amd: Handle IOMMU_DOMAIN_DMA in ops->domain_free call-back
iommu/amd: Use dev_data->domain in get_domain()
iommu/amd: Optimize map_sg and unmap_sg
iommu/amd: Introduce dir2prot() helper
iommu/amd: Implement timeout to flush unmap queues
iommu/amd: Implement flush queue
iommu/amd: Allow NULL pointer parameter for domain_flush_complete()
iommu/amd: Set up data structures for flush queue
iommu/amd: Remove align-parameter from __map_single()
iommu/amd: Remove other remains of old address allocator
iommu/amd: Make use of the generic IOVA allocator
iommu/amd: Remove special mapping code for dma_ops path
iommu/amd: Pass gfp-flags to iommu_map_page()
iommu/amd: Implement apply_dm_region call-back
iommu/amd: Create a list of reserved iova addresses
...
Pull mailbox updates from Jussi Brar:
"Broadcom:
- New PDC controller driver and bindings
Misc:
- PL320 - Convert from 'raw' IO to 'relaxed' version
- Test - fix dangling pointer"
* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Fix format and type mismatches in Broadcom PDC driver
mailbox: Add Broadcom PDC mailbox driver
dt-bindings: add bindings documentation for PDC driver.
mailbox: pl320: remove __raw IO
mailbox: mailbox-test: set tdev->signal to NULL after freeing
x86_64 needs to use compat_sys_keyctl for 32-bit userspace rather than
calling sys_keyctl(). The latter will work in a lot of cases, thereby
hiding the issue.
Reported-by: Stephan Mueller <smueller@chronox.de>
Tested-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: keyrings@vger.kernel.org
Cc: linux-security-module@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/146961615805.14395.5581949237156769439.stgit@warthog.procyon.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On Acer Veriton machines, codec with subsystem-id 0x1b0a01b8 the port at
0x15 is configured by default as an Internal Speaker (0x90170120).
However, no physical is speaker installed on-board. This patch adds a quirk
which disables the physical connection on this pin.
BugLink: https://bugs.launchpad.net/bugs/1607647
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have a Dell AIO on which we can't adjust its speaker's volume.
The problem is it is connected to a Audio Output node without Amp-out
capability. To fix it, we change it to be connnected to a node with
Amp-out capability.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are KSZ8721 PHYs with phy_id 0x00221619. In order to detect them
as PHY_ID_KSZ8001 compatible while staying different to PHY_ID_KSZ9021
ignore the last two bits when matching PHY_ID
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chunhao Lin says:
====================
r8169: fix 3 runtime pm related issues.
v2:
use "struct device *d = &tp->pci_dev->dev" instead of "struct pci_dev *pdev = tp->pci_dev"
v1:
This series of patches fix 3 runtime pm related issues that are listed below.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is no AC power, NIC may not work after changing mac address.
Please refer to following link.
http://www.spinics.net/lists/netdev/msg356572.html
This issue is caused by runtime power management. When there is no AC
power, if we put NIC down (ifconfig down), the driver will be in runtime
suspend state and hardware will be put into D3 state. During this time,
driver cannot access hardware regisers. So if you set new mac address
during this time, it will not be set to hardware. After resume, NIC will
keep using the old mac address and the network will not work normally.
In this patch I add detecting runtime pm status when setting mac address.
If driver is in runtime suspend state, it will skip setting mac address, keep
the new mac address, and set the new mac address during runtime resume.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not to call rtl8169_update_counters() to dump tally counter when driver
is in runtime suspend state.
Calling rtl8169_update_counters() in runtime suspend state will produce
warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)".
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC will be put into D3 state during runtime suspend state. When set or
get hardware wol setting, driver will write or read hardware registers.
If we set or get hardware wol setting in runtime suspend state, because
NIC will in D3 state, the hardware registers read by driver will return all
0xff. That will let driver thinking register flag is not toggled and
then prints the warning message "rtl_counters_cond == 1 (loop: 1000,
delay: 10)" to kernel log.
For fixing this issue, add checking driver's pm runtime status in
rtl8169_get_wol() and rtl8169_set_wol().
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wzSC
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds"
* tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc: (135 commits)
mmc: rtsx_pci: Remove deprecated create_singlethread_workqueue
mmc: rtsx_pci: Enable MMC_CAP_ERASE to allow erase/discard/trim requests
mmc: rtsx_pci: Use the provided busy timeout from the mmc core
mmc: sdhci-pltfm: Drop define for SDHCI_PLTFM_PMOPS
mmc: sdhci-pltfm: Convert to use the SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pltfm: Make sdhci_pltfm_suspend|resume() static
mmc: sdhci-esdhc-imx: Use common sdhci_suspend|resume_host()
mmc: sdhci-esdhc-imx: Assign system PM ops within #ifdef CONFIG_PM_SLEEP
mmc: sdhci-sirf: Remove non needed #ifdef CONFIG_PM* for dev_pm_ops
mmc: sdhci-s3c: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-pxav3: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-of-esdhc: Simplify code by using SIMPLE_DEV_PM_OPS
mmc: sdhci-acpi: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pci-core: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: Change the max discard sectors and erase response when HW busy detect
phy: rockchip-emmc: Wait even longer for the DLL to lock
phy: rockchip-emmc: Be tolerant to card clock of 0 in power on
mmc: sdhci-of-arasan: Revert: Always power the PHY off/on when clock changes
mmc: sdhci-msm: Add support for UHS cards
mmc: sdhci-msm: Add set_uhs_signaling() implementation
...
Pull watchdog updates from Wim Van Sebroeck:
"Core:
- min and max timeout improvements, WDOG_HW_RUNNING improvements,
status funtionality
- Add a device managed API for watchdog_register_device()
New watchdog drivers:
- Aspeed SoCs
- Maxim PMIC MAX77620
- Amlogic Meson GXBB SoC
Enhancements:
- support for the r8a7796 watchdog device
- support for F81866 watchdog device
- support for 5th variation of Apollo Lake
- support for MCP78S chipset
- clean-up of softdog.c watchdog device driver
- pic32-wdt and pic32-dmt fixes
- Documentation/watchdog: watchdog-test improvements
- several other fixes and improvements"
* git://www.linux-watchdog.org/linux-watchdog: (50 commits)
watchdog: gpio_wdt: Fix missing platform_set_drvdata() in gpio_wdt_probe()
watchdog: core: Clear WDOG_HW_RUNNING before calling the stop function
watchdog: core: Fix error handling of watchdog_dev_init()
watchdog: pic32-wdt: Fix return value check in pic32_wdt_drv_probe()
watchdog: pic32-dmt: Remove .owner field for driver
watchdog: pic32-wdt: Remove .owner field for driver
watchdog: renesas-wdt: Add support for the r8a7796 wdt
Documentation/watchdog: check return value for magic close
watchdog: sbsa: Drop status function
watchdog: Implement status function in watchdog core
watchdog: tangox: Set max_hw_heartbeat_ms instead of max_timeout
watchdog: change watchdog_need_worker logic
watchdog: add support for MCP78S chipset in nv_tco
watchdog: bcm2835_wdt: remove redundant ->set_timeout callback
watchdog: bcm2835_wdt: constify _ops and _info structures
dt-bindings: watchdog: Add Meson GXBB Watchdog bindings
watchdog: Add Meson GXBB Watchdog Driver
watchdog: qcom: configure BARK time in addition to BITE time
watchdog: qcom: add option for standalone watchdog not in timer block
watchdog: qcom: update device tree bindings
...
Pull btrfs updates from Chris Mason:
"This pull is dedicated to Josef's enospc rework, which we've been
testing for a few releases now. It fixes some early enospc problems
and is dramatically faster.
This also includes an updated fix for the delalloc accounting that
happens after a fault in copy_from_user. My patch in v4.7 was almost
but not quite enough"
* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix delalloc accounting after copy_from_user faults
Btrfs: avoid deadlocks during reservations in btrfs_truncate_block
Btrfs: use FLUSH_LIMIT for relocation in reserve_metadata_bytes
Btrfs: fill relocation block rsv after allocation
Btrfs: always use trans->block_rsv for orphans
Btrfs: change how we calculate the global block rsv
Btrfs: use root when checking need_async_flush
Btrfs: don't bother kicking async if there's nothing to reclaim
Btrfs: fix release reserved extents trace points
Btrfs: add fsid to some tracepoints
Btrfs: add tracepoints for flush events
Btrfs: fix delalloc reservation amount tracepoint
Btrfs: trace pinned extents
Btrfs: introduce ticketed enospc infrastructure
Btrfs: add tracepoint for adding block groups
Btrfs: warn_on for unaccounted spaces
Btrfs: change delayed reservation fallback behavior
Btrfs: always reserve metadata for delalloc extents
Btrfs: fix callers of btrfs_block_rsv_migrate
Btrfs: add bytes_readonly to the spaceinfo at once
This patch enables support for Performance monitor registers related
ELF core note NT_PPC_PMU based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding one new register sets REGSET_PMU in powerpc
corresponding to the ELF core note sections added in this
regard. It also implements the get, set and active functions
for this new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for EBB state registers related
ELF core note NT_PPC_EBB based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding one new register sets REGSET_EBB in powerpc
corresponding to the ELF core note sections added in this
regard. It also implements the get, set and active functions
for this new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for running TAR, PPR, DSCR registers
related ELF core notes NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR based
ptrace requests through PTRACE_GETREGSET, PTRACE_SETREGSET calls.
This is achieved through adding three new register sets REGSET_TAR,
REGSET_PPR, REGSET_DSCR in powerpc corresponding to the ELF core
note sections added in this regad. It implements the get, set and
active functions for all these new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for all three TM checkpointed SPR
states related ELF core note NT_PPC_TM_CTAR, NT_PPC_TM_CPPR,
NT_PPC_TM_CDSCR based ptrace requests through PTRACE_GETREGSET,
PTRACE_SETREGSET calls. This is achieved through adding three
new register sets REGSET_TM_CTAR, REGSET_TM_CPPR and
REGSET_TM_CDSCR in powerpc corresponding to the ELF core note
sections added. It implements the get, set and active functions
for all these new register sets added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM SPR state related ELF core
note NT_PPC_TM_SPR based ptrace requests through PTRACE_GETREGSET,
PTRACE_SETREGSET calls. This is achieved through adding a register
set REGSET_TM_SPR in powerpc corresponding to the ELF core note
section added. It implements the get, set and active functions for
this new register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed VSX register
set ELF core note NT_PPC_CVSX based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CVSX in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed VMX register
set ELF core note NT_PPC_CVMX based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CVMX in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed FPR register
set ELF core note NT_PPC_CFPR based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CFPR in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables support for TM checkpointed GPR register
set ELF core note NT_PPC_CGPR based ptrace requests through
PTRACE_GETREGSET, PTRACE_SETREGSET calls. This is achieved
through adding a register set REGSET_CGPR in powerpc
corresponding to the ELF core note section added. It
implements the get, set and active functions for this new
register set added.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch splits gpr32_get, gpr32_set functions to accommodate
in transaction ptrace requests implemented in patches later in
the series.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PPC_VSX ptrace requests. The
function vsr_get which gets the running value of all VSX registers
and the function vsr_set which sets the running value of of all VSX
registers work on the running set of VMX registers whose location
will be different if transaction is active. This patch makes these
functions adapt to situations when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PPC_VMX ptrace requests. The
function vr_get which gets the running value of all VMX registers
and the function vr_set which sets the running value of of all VMX
registers work on the running set of VMX registers whose location
will be different if transaction is active. This patch makes these
functions adapt to situations when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch enables in transaction NT_PRFPREG ptrace requests.
The function fpr_get which gets the running value of all FPR
registers and the function fpr_set which sets the running
value of of all FPR registers work on the running set of FPR
registers whose location will be different if transaction is
active. This patch makes these functions adapt to situations
when the transaction is active.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch creates a function flush_tmregs_to_thread which
will then be used by subsequent patches in this series. The
function checks for self tracing ptrace interface attempts
while in the TM context and logs appropriate warning message.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds twelve ELF core note sections for powerpc
architecture for various registers and register sets which
need to be accessed from ptrace interface and then gdb.
These additions include special purpose registers like TAR,
PPR, DSCR, TM running and checkpointed state for various
register sets, EBB related register set, performance monitor
register set etc. Addition of these new ELF core note
sections extends the existing ELF ABI on powerpc arch without
affecting it in any manner.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This should be same as flush_tlb_page except for hash32. For hash32
I guess the existing code is wrong, because we don't seem to be
flushing tlb for Hash != 0 case at all. Fix this by switching to
calling flush_tlb_page() which does the right thing by flushing
tlb for both hash and nohash case with hash32
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some archs like ppc64 need to do special things when flushing tlb for
hugepage. Add a new helper to flush hugetlb tlb range. This helps us to
avoid flushing the entire tlb mapping for the pid.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use the helper instead of open coding the same at multiple place
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of flushing the entire mm, implement a flush_pmd_tlb_range
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use flush_hugetlb_page instead of flush_tlb_page when we clear flush the
pte.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Replace opencoding of the same at multiple places with the helper.
No functional change with this patch.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we track page size in mmu_gather, we can use address based
tlbie format when doing a tlb_flush(). We don't do this if we are
invalidating the full address space.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a comment to the generated assembler for jump labels. This makes it
easier to identify them in asm listings (generated with $ make foo.s).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This allows us to catch incorrect usage of cpu_has_feature() and
mmu_has_feature() prior to jump labels being initialised.
mpe: Use printk() and dump_stack() rather than WARN_ON(), because
WARN_ON() may not work this early in boot. Rename the Kconfig.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As we just did for CPU features.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
