After going through the trouble of setting up the PIC base
address in the pic@40000 device tree node, use it instead
of the obsolete hard-coded value.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Several RTAS calls take a "config_addr" parameter, which is a particular
way of specifying a PCI busno, devfn and register number into a 32-bit word.
Currently these are open-coded, and I'll be adding another soon, replace
them with a helper that encapsulates the logic. Be more strict about masking
the busno too, just in case.
Booted on P5 LPAR.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup CPU inits a bit more, Geoff Levand already did some earlier.
* Move CPU state save to cpu_setup, since cpu_setup is only ever done
on cpu 0 on 64-bit and save is never done more than once.
* Rename __restore_cpu_setup to __restore_cpu_ppc970 and add
function pointers to the cputable to use instead. Powermac always
has 970 so no need to check there.
* Rename __970_cpu_preinit to __cpu_preinit_ppc970 and check PVR before
calling it instead of in it, it's too early to use cputable.
* Rename pSeries_secondary_smp_init to generic_secondary_smp_init since
everyone but powermac and iSeries use it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Neil Brown observed that the current limit of 32 bytes isn't enough to hold two
ip addresses and the rest of the stuff we're putting in it, so it's often
truncated to the point where it's unlikely to be unique. This can cause
spurious CLID_INUSE's from the server.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
(cherry picked from fc8c17ec251e984ab3df9182ed097aa5b577c915 commit)
Some hardware uses port 664 for its hardware-based IPMI listener. Teach
the RPC client to avoid using that port by raising the default minimum port
number to 665.
Test plan:
Find a mainboard known to use port 664 for IPMI; enable IPMI; mount NFS
servers in a tight loop.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
(cherry picked from 58e8cb3a035d22fc386e1c53a5d98c3f219530fb commit)
Make it take a dentry argument instead of a path
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
(cherry picked from 648d4116eb2509f010f7f34704a650150309b3e7 commit)
The biggest change is that ata_host_set is renamed to ata_host.
* ata_host_set => ata_host
* ata_probe_ent->host_flags => ata_probe_ent->port_flags
* ata_probe_ent->host_set_flags => ata_probe_ent->_host_flags
* ata_host_stats => ata_port_stats
* ata_port->host => ata_port->scsi_host
* ata_port->host_set => ata_port->host
* ata_port_info->host_flags => ata_port_info->flags
* ata_(.*)host_set(.*)\(\) => ata_\1host\2()
The leading underscore in ata_probe_ent->_host_flags is to avoid
reusing ->host_flags for different purpose. Currently, the only user
of the field is libata-bmdma.c and probe_ent itself is scheduled to be
removed.
ata_port->host is reused for different purpose but this field is used
inside libata core proper and of different type.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Tue, 2006-08-15 at 08:22 -0700, Dave Hansen wrote:
> kernel BUG in cache_free_debugcheck at mm/slab.c:2748!
Alright, this one is only triggered when slab debugging is enabled. The
slabs are assumed to be aligned on a HUGEPTE_TABLE_SIZE boundary. The free
path makes use of this assumption and uses the lowest nibble to pass around
an index into an array of kmem_cache pointers. With slab debugging turned
on, the slab is still aligned, but the "working" object pointer is not.
This would break the assumption above that a full nibble is available for
the PGF_CACHENUM_MASK.
The following patch reduces PGF_CACHENUM_MASK to cover only the two least
significant bits, which is enough to cover the current number of 4 pgtable
cache types. Then use this constant to mask out the appropriate part of
the huge pte pointer.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch rewrites mpc7448hpc2 board irq support according to the new
mpic device tree interface.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are two problems in the powerpc gettimeofday code which can
cause incorrect results to be returned.
The first is that there is a race between do_gettimeofday and the
timer interrupt:
1. do_gettimeofday does get_tb()
2. decrementer exception on boot cpu which runs timer_recalc_offset,
which also samples the timebase and updates the do_gtod structure
with a greater timebase value.
3. do_gettimeofday calls __do_gettimeofday, which leads to the
negative result from tb_val - temp_varp->tb_orig_stamp.
The second is caused by taking the boot cpu offline, which can cause
the value of tb_last_jiffy to be increased past the currently
available timebase, causing the same underflow as above.
[paulus@samba.org - define and use data_barrier() instead of mb().]
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The "%uhi" needs to be "%%uhi" because we want a real
"%" character in the assembler here, instead of an
assembler variable expansion.
Aparently older GCCs were more liberal and interpreted
this %-letter as a literal "%" for whatever reason.
Based upon a build failure report from Meelis Roos.
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_make_abort_user() now takes the msg_len along with the msg
so that we don't have to recalculate the bytes in iovec.
It also uses memcpy_fromiovec() so that we don't go beyond the
length allocated.
It is good to have this fix even if verify_iovec() is fixed to
return error on overflow.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This contains board-specific portion to respect driver changes (for 8272ads ,
885ads and 866ads). Altered platform_data structures as well as initial setup
routines relevant to fs_enet.
Changes to the mpc8560ads ppc/ code are also introduced, but mainly as
reference, since the entire board support is going to appear in arch/powerpc.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This makes it possible for HW PHY-less boards to utilize PAL goodies. Generic
routines to connect to fixed PHY are provided, as well as ability to specify
software callback that fills up link, speed, etc. information into PHY
descriptor (the latter feature not tested so far).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch updates the fc transport for the following:
- Addition of a new attribute "system_hostname" which can be
used to set the fully qualified hostname that the fc_host
is attached to. The fc_host can then register this string
as the FDMI-based host name attribute.
Note: for NPIV, a fc_host could be associated with a system which
is not the local system.
- Add the inline function u64_to_wwn(), which is the inverse of the
existing wwn_to_u64() function.
- Slight reorg, just to keep dynamic attributes with each other, etc
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Paul Gortmaker
Some folks here at Wind River asked me if I'd push this out
so that the value was generally agreed upon in advance by
all folks interested in working with iWMMXt. Seems simple
enough...
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
A number of small issues with the S3C24XX DMA have
cropped up, which this patch fixes. These are:
- check wether we can load another buff in start
- update state handling in s3c2410_dma_lastxfer
- only reload in irq if channel is not idle
- more informative timeout errors (add source)
- do not call request_irq() with irqs locked
- added waitforstop function
The patch also adds a S3C2410_DMAOP_STARTED for
the occasions when the driver wants to ensure that
the DMA system load state is resynced after loading.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the bridge recomputes features, it does not maintain the
constraint that SG/GSO must be off if TX checksum is off.
This patch adds that constraint.
On a completely unrelated note, I've also added TSO6 and TSO_ECN
feature bits if GSO is enabled on the underlying device through
the new NETIF_F_GSO_SOFTWARE macro.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since __vlan_hwaccel_rx() is essentially bypassing the
netif_receive_skb() call that would have occurred if we did the VLAN
decapsulation in software, we are missing the skb_bond() call and the
assosciated checks it does.
Export those checks via an inline function, skb_bond_should_drop(),
and use this in __vlan_hwaccel_rx().
Signed-off-by: David S. Miller <davem@davemloft.net>
To compile kexec on 32-bit we need a few more bits and pieces. Rather
than add empty definitions, we can make crash.c work on 32-bit, with
only a couple of kludges.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Atmel flash chips don't have PRI information in the same format as
AMD flash chips. This patch installs a fixup for all Atmel chips that
converts the relevant PRI fields into AMD format.
Only the fields that are actually used by the command set is actually
converted. The rest are initialized to zero (which should be safe)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Don't let fuse_readpages leave the @pages list not empty when exiting
on error.
[akpm@osdl.org: kernel-doc fixes]
Signed-off-by: Alexander Zarochentsev <zam@namesys.com>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
linux/backlight.h pulls in header files (eg. ioport.h) that break
compilation of userspace programs. To solve the problem, only include
backlight.h in fb.h if compiling kernel stuff.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The CFA world has some additional rules and drive modes we need to support for
newer expansion cards and on embedded boxes
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The IPv4/IPv6 datagram output path was using skb_trim to trim paged
packets because they know that the packet has not been cloned yet
(since the packet hasn't been given to anything else in the system).
This broke because skb_trim no longer allows paged packets to be
trimmed. Paged packets must be given to one of the pskb_trim functions
instead.
This patch adds a new pskb_trim_unique function to cover the IPv4/IPv6
datagram output path scenario and replaces the corresponding skb_trim
calls with it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
pr_debug() should not be used from drivers, add comment saying that.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also, moved ATA_MAX_SECTORS and ATA_MAX_SECTORS_LBA48 from
linux/libata.h to linux/ata.h, now that they truly reflect the standard
(well... mostly; note TODO comment).
This changes the performance profile (and potential bug profile)
for a bunch of drivers, so be wary.
Implement dummy port which can be requested by setting appropriate bit
in probe_ent->dummy_port_mask. The dummy port is used as placeholder
for stolen legacy port. This allows libata to guarantee that
index_of(ap) == ap->port_no == actual_device_port_no, and thus to
remove error-prone ap->hard_port_no.
As it's used only when one port of a legacy controller is reserved by
some other entity (e.g. IDE), the focus is on keeping the added *code*
complexity at minimum, so dummy port allocates all libata core
resources and acts as a normal port. It just has all dummy port_ops.
This patch only implements dummy port. The following patch will make
libata use it for stolen legacy ports.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Kill host_set->next
Fix simplex support
Allow per platform setting of IDE legacy bases
Some of this can be tidied further later on, in particular all the
legacy port gunge belongs as a PCI quirk/PCI header decode to understand
the special legacy IDE rules in the PCI spec.
Longer term Jeff also wants to move the request_irq/free_irq out of core
which will make this even cleaner.
tj: folded in three followup patches - ata_piix-fix, broken-arch-fix
and fix-new-legacy-handling, and separated per-dev xfermask into
separate patch preceding this one. Folded in fixes are...
* ata_piix-fix: fix build failure due to host_set->next removal
* broken-arch-fix: add missing include/asm-*/libata-portmap.h
* fix-new-legacy-handling:
* In ata_pci_init_legacy_port(), probe_num was incorrectly
incremented during initialization of the secondary port and
probe_ent->n_ports was incorrectly fixed to 1.
* Both legacy ports ended up having the same hard_port_no.
* When printing port information, both legacy ports printed
the first irq.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tejun Heo <htejun@gmail.com>
The following patch enhances libata to allow SAS device drivers
to utilize libata to talk to SATA devices. It introduces some
new APIs which allow libata to be used without allocating a
virtual scsi host.
New APIs:
ata_sas_port_alloc - Allocate an ata_port
ata_sas_port_init - Initialize an ata_port (probe device, etc)
ata_sas_port_destroy - Free an ata_port allocated by ata_sas_port_alloc
ata_sas_slave_configure - configure scsi device
ata_sas_queuecmd - queue a scsi command, similar to ata_scsi_queuecomand
These new APIs can be used either directly by a SAS LLDD or could be used
by the SAS transport class.
Possible usage for a SAS LLDD would be:
scsi_scan_host
target_alloc
ata_sas_port_alloc
slave_alloc
ata_sas_port_init
slave_configure
ata_sas_slave_configure
Commands received by the LLDD for SATA devices would call ata_sas_queuecmd.
Device teardown would occur with:
slave_destroy
port_disable
target_destroy
ata_sas_port_destroy
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jack Steiner identified a problem where XPC can cause a silent
data corruption. On module load, the placement may cause the
xpc_remote_copy_buffer to span two physical pages. DMA transfers are
done to the start virtual address translated to physical.
This patch changes the buffer from a statically allocated buffer to a
kmalloc'd buffer. Dean Nelson reviewed this before posting. I have
tested it in the configuration that was showing the memory corruption
and verified it works. I also added a BUG_ON statement to help catch
this if a similar situation is encountered.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
