The pci config space accessors on s390 are (now) smart enough to
figure out if a pci function is available. So instead of calling
pci_create_root_bus and then pci_scan_single_device for each
available function just call pci_scan_root_bus and let the pci core
do the scanning (via config reads on all possible functions) and
device creation.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the allocation of a single request fails the already allocated
requests will not be freed.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow 0 and powers of 2 between 2 and 128 for write_cluster_size.
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When we fetch an interrupt on the CCW console using tsch (via
ccw_device_wait_idle formerly known as wait_cons_dev) we increment
the irq count for the affected interruption class but it is not
accounted as an IO interrupt.
This is broken since commit b603d258a4
"s390: remove superfluous tpi from wait_cons_dev"
Fix it so that the sum of the individual interrupts per class matches
the number of IO interrupts again.
Reported-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case a machine supports memory hotplug all active memory increments
present at IPL time have been initialized with a "usecount" of 1.
This is wrong if the memory increment size is larger than the memory
section size of the memory hotplug code. If that is the case the
usecount must be initialized with the number of memory sections that
fit into one memory increment.
Otherwise it is possible to put a memory increment into standby state
even if there are still active sections.
Afterwards addressing exceptions might happen which cause the kernel
to panic.
However even worse, if a memory increment was put into standby state
and afterwards into active state again, it's contents would have been
zeroed, leading to memory corruption.
This was only an issue for machines that support standby memory and
have at least 256GB memory.
This is broken since commit fdb1bb15 "[S390] sclp/memory hotplug: fix
initial usecount of increments".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: stable@vger.kernel.org # 2.6.39+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We've seen repeatedly that 8KB stack size on 64 bit kernels
is not sufficient.
So simply remove the config option.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a pointer to the system call table to the thread_info structure.
The TIF_31BIT bit is set or cleared by SET_PERSONALITY exactly once
for the lifetime of a process. With the pointer to the correct system
call table in thread_info the system call code in entry64.S path can
drop the check for TIF_31BIT which saves a couple of instructions.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Store the stack pointers in the lowcore for the kernel stack, the async
stack and the panic stack with the offset required for the first user.
This avoids an unnecessary add instruction on the system call path.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Also add some missing printk levels.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20130425174002.GA26769@redhat.com
[ Tweaked the messages a bit. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We occasionally get reports of these BUGs being hit, and the
stack trace doesn't necessarily always tell us what we need to
know about why we are hitting those limits.
If users start attaching /proc/lock_stats to reports we may have
more of a clue what's going on.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20130423163403.GA12839@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit fc9bbca8f6 (vm: convert fb_mmap to
vm_iomap_memory() helper) made fbmem.c use vm_iomap_memory, but also
accidentally removed the check for mmio's availability.
Add the check back.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Improve fb_mmap bounds checks in gbefb, smscufx, udlfb and vfb drivers to
prevent possible uint overflows.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Bernie Thompson <bernie@plugable.com>
Use vm_iomap_memory() instead of [io_]remap_pfn_range().
vm_iomap_memory() gives us much simpler API to map memory to userspace,
and reduces possibilities for bugs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
on some Apple machines because they implement EFI spec 1.10, which
doesn't provide a QueryVariableInfo() runtime function and the logic
used to check for the existence of that function was insufficient.
Fix from Josh Boyer.
* The anti-bricking algorithm also introduced a compiler warning on
32-bit. Fix from Borislav Petkov.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJReOtLAAoJEC84WcCNIz1VFZgP/Aws1NdPo/RdyI6/oGkI7ZV4
+5O79pLcaJt7ESuWjx2/9pto/qTzsWMri40HZivGbgxw+ViEdprGjJUFqSTn1LyJ
QrYamP40jBdLFfh1oDHvsub8HiC72sjB/ILSoDvooHEniDmajrL6zZK7C66gP+na
Q4ZN/Jp3x3XAW0s1mVJC4VnL60489Q/ndR3SH01hr2gqMSvmjwnhfiio6n9gYvdd
egmoalTIst94+X0nW1VHA4HT3SRM7cuwCA/kDxtG6qitbsQMUKUoa+DOpMNfE8mD
QdzmzZL115O+7ORj8Ki/JNS2CSyI83IRSQ3kcM1J5026mWIBMiM3h9Vlu5NwAyFA
bapZSaYr7S5u9BU/vICGnpyYnSsLfjuB3CnAuJFyM0YVFjR6n7moUpnP1LNifGHX
E/Qr1HDyIwwxE8K0f/n86a7BfstoMjzE74an6wOVXKDUY/RnH+FdWG/HDBPd8iG4
Avei1bK2zLLcXK4Kqmx8EkXTK7VSFx6StCPjAVlpgYOAMpRmQEmNpd/3lF7Y70gp
yXIBTSTKaPZ+/5SaeOPL2sgW37Uo9fFMphww2mLXGIdgO3L0BHD5hIq9pZQ7g0VK
noDN7f6ViCuNYuZIrTAtLo9Oc+KKgqOXa0TovUhORkJ8Gk93moL4fgYyFVPvsYnD
rQuTRJ3pZEEHlCmyZzBl
=l/fT
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' into x86/urgent
* The EFI variable anti-bricking algorithm merged in -rc8 broke booting
on some Apple machines because they implement EFI spec 1.10, which
doesn't provide a QueryVariableInfo() runtime function and the logic
used to check for the existence of that function was insufficient.
Fix from Josh Boyer.
* The anti-bricking algorithm also introduced a compiler warning on
32-bit. Fix from Borislav Petkov.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
User applications running on SMP kernels have long suffered from instability
and random segmentation faults. This patch improves the situation although
there is more work to be done.
One of the problems is the various routines in pgtable.h that update page table
entries use different locking mechanisms, or no lock at all (set_pte_at). This
change modifies the routines to all use the same lock pa_dbit_lock. This lock
is used for dirty bit updates in the interruption code. The patch also purges
the TLB entries associated with the PTE to ensure that inconsistent values are
not used after the page table entry is updated. The UP and SMP code are now
identical.
The change also includes a minor update to the purge_tlb_entries function in
cache.c to improve its efficiency.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
CONFIG_MLONGCALLS was introduced in commit
ec758f9832 to overcome linker issues when linking
huge linux kernels, e.g. with many modules linked in.
But in the kernel module loader there is no support yet for the new relocation
types, which is why modules built with -mlong-calls can't be loaded.
Furthermore, for modules long calls are not really necessary, since we already
use stub sections which resolve long distance calls.
So, let's just disable this compiler option when compiling kernel modules.
Signed-off-by: Helge Deller <deller@gmx.de>
When targetting 32-bit processors, __put_user emits a pair of stw
instructions for the 8-byte case. If the type of __val is a pointer, the
marshalling code casts it to the wider integer type of u64, resulting
in the following compiler warnings:
kernel/signal.c: In function 'copy_siginfo_to_user':
kernel/signal.c:2752:11: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
kernel/signal.c:2752:11: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
[...]
This patch fixes the warnings by removing the marshalling code and using
the correct output modifiers in the __put_{user,kernel}_asm64 macros
so that GCC will allocate the right registers without the need to
extract the two words explicitly.
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Change kunmap macro to static inline function to fix build error
compiling drivers/base/dma-buf.c.
Without the change, the following error can occur:
CC drivers/base/dma-buf.o
drivers/base/dma-buf.c: In function 'dma_buf_kunmap':
drivers/base/dma-buf.c:427:46:
error: macro "kunmap" passed 3 arguments, but takes just 1
I believe parisc is the only arch to implement kunmap using a macro.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
The Debian experimental linux source package (3.8.5-1) build fails
with the following errors:
...
MODPOST 2016 modules
ERROR: "__ucmpdi2" [fs/btrfs/btrfs.ko] undefined!
ERROR: "__ucmpdi2" [drivers/md/dm-verity.ko] undefined!
The attached patch resolves this problem. It is based on the s390
implementation of ucmpdi2.c.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Helge Deller <deller@gmx.de>
The 'help' section of the Kconfig entry for this driver is missing
an extra alignment. That seems to violate what's stated at:
Documentation/kbuild/kconfig-language.txt
Even if it works, the better is to add 2 extra spaces there, as
this is the common practice and helps human reading of the file.
Also, the way it is, it breaks backport trees.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hole reason for __must_check is to not ignore an error.
However, a "ret" value is used at cx25821 just to avoid the
Kernel compilation to compain about it.
That, however, produces another warning (with W=1):
drivers/media/pci/cx25821/cx25821-alsa.c: In function 'cx25821_audio_fini':
drivers/media/pci/cx25821/cx25821-alsa.c:727:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
With the current implementation of driver_for_each_device() and
cx25821_alsa_exit_callback(), there's actually just one
very unlikely condition where it will currently produce
an error: if driver_find() returns NULL.
Ok, there's not much that can be done, as it is on a driver's
function that returns void, but it can at least print some message
if the error happens.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following warning:
drivers/media/pci/cx25821/cx25821-video.c: At top level:
drivers/media/pci/cx25821/cx25821-video.c:766:5: warning: no previous prototype for 'cx25821_vidioc_s_std' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After cx25821-video cleanup, this var is not used anymore:
drivers/media/pci/cx25821/cx25821-video.c: In function 'cx25821_vidioc_try_fmt_vid_cap':
drivers/media/pci/cx25821/cx25821-video.c:591:15: warning: variable 'maxw' set but not used [-Wunused-but-set-variable]
as the code now checks the max width as the default case for the
range check.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the driver complains about the pre_detect var:
drivers/media/tuners/r820t.c: In function 'r820t_sysfreq_sel':
drivers/media/tuners/r820t.c:722:31: warning: variable 'pre_dect' set but not used [-Wunused-but-set-variable]
While rtl8232 code comments it, perhaps some other driver may use.
So, the better is to keep the code there, allowing to enable it
via r820t config data.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The check if the values for c, h and n are within the range is
always true, as, if one of this values is out of range, the
previous "if" clauses will default to a value within the
range.
That fixes the following warning:
drivers/media/dvb-frontends/dib0090.c: In function 'dib0090_set_EFUSE':
drivers/media/dvb-frontends/dib0090.c:1545:5: warning: comparison is always true due to limited range of data type [-Wtype-limits]
and makes the code easier to read.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_wait_lock':
drivers/media/dvb-frontends/dib8000.c:3972:1: warning: 'value' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/dvb-frontends/dib8000.c:2419:6: note: 'value' was declared here
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
isdbt_sb_subchannel is unsigned with 8 bits. So, it will
never be -1. Instead, any value bigger than 13 is invalid.
As is, the current code generates the following warnings:
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_set_isdbt_common_channel':
drivers/media/dvb-frontends/dib8000.c:2358:3: warning: comparison is always true due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c: In function 'dib8000_tune':
drivers/media/dvb-frontends/dib8000.c:3107:8: warning: comparison is always false due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c:3153:9: warning: comparison is always false due to limited range of data type [-Wtype-limits]
drivers/media/dvb-frontends/dib8000.c:3160:5: warning: comparison is always false
It should also be noticed that ARIB STD-B31, item
"3.15.6.8 Number of segments" at TMCC table defines the
value 15 for unused segment, and 14 as reserved.
So, better to change the check to consider any value
bigger than 13 to mean that sub-channels should be
disabled, fixing the warning and doing the right thing
even if an invalid value is filled by userspace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gcc-3.8 correctly found that the variables set by find_freq_tables()
are not initialized if this function is called on something other
than a pxa2xx or pxa3xx:
pxa2xx-cpufreq.c: In function 'pxa_verify_policy':
pxa2xx-cpufreq.c:272:6: warning: 'pxa_freqs_table' may be used uninitialized in this function [-Wmaybe-uninitialized]
pxa2xx-cpufreq.c: In function 'pxa_set_target':
pxa2xx-cpufreq.c:345:23: warning: 'pxa_freq_settings' may be used uninitialized in this function [-Wmaybe-uninitialized]
Rather than adding a bogus initialization that would let us
get a little further before crashing, add an explicit BUG().
We know that this code is designed to run on only these cpus,
so this will fix the build warning and give a more helpful
diagnostic if the code ever changes to run on other machines.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Kconfig entry for USB_EHCI_MSM unconditionally selects USB_MSM_OTG,
which is now only visible when USB_PHY is also enabled.
This adds an appropriate dependency and enables USB_PHY in the msm
defconfig, avoiding the Kbuild warning:
warning: (USB_EHCI_MSM) selects USB_MSM_OTG which has unmet direct dependencies (USB_SUPPORT && USB_PHY && (USB || USB_GADGET) && ARCH_MSM)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the EHCI driver, OHCI supports a large number of different platform
glue drivers by directly including them, which causes problems with
conflicting macro definitions in some cases. As more ARM architecture
specific back-ends are required to coexist in a single build, we should
split those out into separate drivers. Unfortunately, the infrastructure
for that is still under development, so to give us more time, this uses
a separate *_PLATFORM_DRIVER macro for each ARM specific OHCI backend,
just like we already do on PowerPC and some of the other ARM platforms.
In linux-3.10, only the SPEAr and CNS3xxx back-ends would actually conflict
without this patch, but over time we would get more of them, so this
is a way to avoid having to patch the driver every time it breaks. We
should still split out all back-ends into separate loadable modules,
but that work is only needed to improve code size and cleanliness after
this patch, not for correctness.
While we're here, this fixes the incorrectly sorted error path
for the OMAP1 and OMAP3 backends to ensure we always unregister
the exact set of drivers that were registered before erroring out.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig entry for USB_OMAP unconditionally selects USB_ISP1301,
which is now only visible when USB_PHY is also enabled.
This adds an appropriate dependency and enables USB_PHY in the omap1
defconfig, avoiding these build warnings:
warning: (USB_OHCI_HCD && USB_OMAP) selects ISP1301_OMAP which has unmet direct dependencies (USB_SUPPORT && USB_PHY && I2C && ARCH_OMAP_OTG)
Also fix a Makefile typo while we're at it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig entry for USB_LPC32XX unconditionally selects USB_ISP1301,
which is now only visible when USB_PHY is also enabled.
This adds an appropriate dependency and enables USB_PHY in the msm
defconfig, avoiding these build errors:
warning: (USB_LPC32XX) selects USB_ISP1301 which has unmet direct dependencies (USB_SUPPORT && USB_PHY && (USB || USB_GADGET) && I2C)
drivers/built-in.o: In function `usb_hcd_nxp_probe':
drivers/usb/host/ohci-nxp.c:224: undefined reference to `isp1301_get_client'
drivers/built-in.o: In function `lpc32xx_udc_probe':
drivers/usb/gadget/lpc32xx_udc.c:3071: undefined reference to `isp1301_get_client'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, if you pass the kernel a dtb where a cpu node has an
unsupported enable-method property (e.g. "not-psci"), it'll explode
horribly, as it iterates over the enable_ops array incorrectly. It
increments the pointer *at* the current element, rather than
incrementing the pointer *to* the current element. As the first two
elements pointed to structures that were contiguous in memory, this
happened to be equivalent. However the third element is NULL, so when
the list is exhausted, smp_get_enable_ops generates the wrong pointer,
and dereferences an arbitrary portion of memory, which currently happens
to contain zero.
This patch fixes this by indirecting the pointer one level, so we
iterate over the array elements correctly, avoiding the below panic:
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
show_pte makes use of the *_none_or_clear_bad style functions. If a
pgd, pud or pmd is identified as being bad, it will then be cleared.
As show_pte appears to be called from either the user or kernel
fault handlers this side effect can lead to unpredictable behaviour;
especially as TLB entries are not invalidated.
This patch removes the page table sanitisation from show_pte. If a
bad pgd, pud or pmd is encountered it is left unmodified.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The compat_stat structure doesn't match the arch/arm/ struct stat
definition. This patch fixes the compat types and struct compat_stat
definition accordingly.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
The DSB following TLB or cache maintenance ops must be run on the same
CPU. With kernel preemption enabled or for user-space cache maintenance
this may not be the case. This patch adds an explicit DSB in the
__switch_to() function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For compiling with allmodconfig, need vga.h file, so generate it which
just only include the asm-generic one.
It is firstly used by drivers/gpu/drm/drm_irq.c.
The related error:
include/video/vga.h:22:21: fatal error: asm/vga.h: No such file or directory
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For systems where the top 32-bits of the MPIDR are all zero, we should
allow the device-tree to specify an #address-size of 0x1 for the CPU reg
property and then zero extend the value there.
Without this patch, kvmtool breaks with the recent mpidr parsing code
introduced in 4c7aa00213 ("arm64: kernel: initialise cpu_logical_map
from the DT").
Acked-by: Javi Merino <javi.merino@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
dtv_property_cache is used on several places on very long lines.
On all places it is used, a long list of struct reference is done.
Instead of doing it, at the routines where it is used more than once,
replace it by one temporary var. That may help the compiler to
use a better code. It also makes easier to review the code, as the
lines becomes closer to 80 columns, making them a way clearer
to read.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/tuners/r820t.c: In function 'r820t_imr':
drivers/media/tuners/r820t.c:1871:8: warning: 'n_ring' may be used uninitialized in this function [-Wmaybe-uninitialized]
Mauro: This is a FALSE POSITIVE: the loop will always return a value
for n_ring, as the last test will fill it with 15, if the loop fails.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've moved the kfree(fe->tuner_priv) one line earlier, otherwise it is
a no-op.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The test as written is always false. It looks like the intent was to
test that the bit was not set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* topic/r820t: (31 commits)
[media] r820t: Don't divide the IF by two
[media] r820t: disable auto gain/VGA setting
[media] rtl2832: Fix IF calculus
[media] r820t: put it into automatic gain mode
[media] r820t: Fix hp_cor filter mask
[media] r820t: fix PLL calculus
[media] r820t: Don't put it in standby if not initialized yet
[media] r820t: avoid rewrite all regs when not needed
[media] r820t: Allow disabling IMR callibration
[media] r820t: add a commented code for GPIO
[media] r820t: add IMR calibrate code
[media] r820t: proper initialize the PLL register
[media] r820t: use usleep_range()
[media] r820t: fix prefix of the r820t_read() function
[media] r820t: split the function that read cached regs
[media] r820t: better report signal strength
[media] r820t: add support for diplexer
[media] r820t: Show the read data in the bit-reversed order
[media] r820t: use the second table for 7MHz
[media] r820t: Invert bits for read ops
...
drivers/media/usb/dvb-usb-v2/anysee.c: In function ‘anysee_frontend_attach’:
drivers/media/usb/dvb-usb-v2/anysee.c:641: warning: ‘ret’ may be used uninitialized in this function
And gcc is right (see the ANYSEE_HW_507T case), so initialize ret to zero
to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
