In some case we weren't releasing the AGP device at module unloading.
This leaded to unfunctional AGP at next module load. This patch make
sure we release the AGP bus if we acquire it.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R300 family will hard lockup if host path read cache flush is
done through MMIO to HOST_PATH_CNTL. But scheduling same flush
through ring seems harmless. This patch remove the hdp_flush
callback and add a flush after each fence emission which means
a flush after each IB schedule. Thus we should have same behavior
without the hard lockup.
Tested on R100,R200,R300,R400,R500,R600,R700 family.
V2: Adjust fence counts in r600_blit_prepare_copy()
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Long story short, this fixes sporadic hardlocks with my rv410 during
times of intense 2D acceleration (Flash on Fx3).
V2: Fix indentation and move errata_fini to suspend function so we
don't leak scratch register over suspend/resume cycle.
V3: Move scratch_reg to asic specific structure (aim is to slowly
move stuff to asic specific structure and avoid poluting
radeon_device struct with asic specific variables)
Signed-off-by: Corbin Simpson <MostAwesomeDude@gmail.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This detects if the sideport memory is enabled and
if it is VRAM is evicted on suspend/resume.
This should fix s/r issues on some IGPs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are a couple of array overruns, and some associated confusion in
the code.
This is just a wild guess at what the code should actually look like.
Coverity CID: 13305 13306
agd5f: fix up the original intent of the timing code
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is displayport used for internal connections such
as laptop panels and systems with integrated monitors.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a new connector type for eDP (embedded displayport)
eDP is more or less the same as DP but there are some
cases when you might want to handle it separately.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Makes it easier to keep in sync with ddx and the upstream
AMD versions.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also remove the problematic enums that were unused
remnants from the ddx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Somehow, strange characters made their way zaurus gpio .desc
fields. Fix it.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Stanislav Brabec <utx@penguin.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In the driver probe function the emac module clock needs to
be enabled before calling register_netdev(). As soon as the
device is registered the driver get_stats function can be invoked
by the core - the module clock must be switched on to be able to
read from stats registers. Also explicitly call matching clk_disable
for failure conditions in probe function.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Davicom DM9100 and DM9102 chips are used on the motherboards of
some SPARC systems (supported by the tulip driver) and also in PCI
expansion cards (supported by the dmfe driver). There is no
difference in the PCI device ids for the two different configurations,
so these drivers both claim the device ids. However, it is possible
to distinguish the two configurations by the presence of Open Firmware
properties for them, so we do that.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc is still throwing a warning that is could be used
uninitialized. This fixes it, and properly formats the device ID
checks for the use of this variable.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dwmac1000 naming instead of gmac.
The patch also splits the gmac.c file in two new ones:
dwmac1000_core.c and dwmac1000_dma.c.
This could actually help on some architectures where different
DMA engines are used.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the mac100.[ch] as dwmac100.[ch]; this
looks more specific and appropriate for these chip series.
The patch also fixes some spare coding style issues.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the dma related functions (interrupt, start, stop etc.)
out from the main driver code. This will help to support new DMA
engines.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reorganises the internal stmmac ops structure.
The stmmac_ops has been splitted into other three structures named:
stmmac_ops
stmmac_dma_ops
stmmac_desc_ops
This makes the code more clear and also helps the next work to
make the driver more generic.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, fix_mac_speed is used for
configuring some sysconf registers according
to the working speed.
This patch fixes the fix_mac_speed invocation
that cannot be done if it is a NULL pointer.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms it can be required a different
configuration of the bus. This can be done
by invoking the bus_setup. It is defined
for all the platforms that needs this kind of
configuration.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rewiews and reorganises all the data
come from the platform removing any dependency
from the stm code.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr.
Note: this patch also removes a debug printk used for displaying the
mac addresses. Indeed, it's is possible to dump the registers with
ethtool.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pMF kernel extension to display the MAC address.
The address will still be displayed in the FDDI Canonical format.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pMF kernel extension to display the MAC address.
The address will still be displayed in the FDDI Canonical format.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Mon, 2010-01-04 at 23:43 +0000, Maciej W. Rozycki wrote:
> The example below shows an address, and the sequence of bits or symbols
> that would be transmitted when the address is used in the Source Address
> or Destination Address fields on the MAC header. The transmission line
> shows the address bits in the order transmitted, from left to right. For
> IEEE 802 LANs these correspond to actual bits on the medium. The FDDI
> symbols line shows how the FDDI PHY sends the address bits as encoded
> symbols.
>
> MSB: 35:7B:12:00:00:01
> Canonical: AC-DE-48-00-00-80
> Transmission: 00110101 01111011 00010010 00000000 00000000 00000001
> FDDI Symbols: 35 7B 12 00 00 01"
>
> Please note that this address has its group bit clear.
>
> This notation is also defined in the "FDDI MEDIA ACCESS CONTROL-2
> (MAC-2)" (X3T9/92-120) document although that book does not have a need
> to use the MSB form and it's skipped.
Adds 6 bytes to object size for x86
New:
$ size lib/vsprintf.o
text data bss dec hex filename
8664 0 2 8666 21da lib/vsprintf.o
$ size lib/vsprintf.o
text data bss dec hex filename
8658 0 2 8660 21d4 lib/vsprintf.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__per_cpu_idtrs is statically allocated ... on CONFIG_NR_CPUS=4096
systems it hogs 16MB of memory. This is way too much for a quite
probably unused facility (only KVM uses dynamic TR registers).
Change to an array of pointers, and allocate entries as needed on
a per cpu basis. Change the name too as the __per_cpu_ prefix is
confusing (this isn't a classic <linux/percpu.h> type object).
Signed-off-by: Tony Luck <tony.luck@intel.com>
Without this fix, some modes couldn't find appropriate clocks.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Matthew Garrett <mjg@redhat.com>
For any given clock we can use the find_pll to get the corresponding DPLL
setting. It is unnecessary to use the find_reduce_pll callback function
to calculate the DPLL parameter for LVDS downclock in order to get the same
divider factor(P) for the normal and downclock.
In theory when the LVDS downclock is supported by LVDS panel, we should get the
same DPLL divider factor(P) for the normal clock and reduced downclock.
If we get the diferent divider factor(P) for normal clock and reduced downclock,
it means that the found downclock is incorrect and should be discarded.
So we should use find_pll callback to calculate the DPLL parameter for the
LVDS reduced downclock as for the normal clock. Then we can do the cleanup
about find_reduced_pll.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As we removed TV hotplug, don't check its status ever.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
linux-next-20081022//include/linux/kgdb.h:308): duplicate section name 'Description'
and fix typos in that file's kernel-doc comments.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
In blackfin, kgdb is running in delayed exception IRQ5 other than in
exception IRQ3 directly. Register reti other than retx in pt_regs is
the kgdb return address. So, don't put PC in gdb_regs into retx.
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Blackfin needs it own arch specific probe_kernel_read() and
probe_kernel_write().
This was moved out of the kgdb code and into the
arch/blackfin/maccess.c, because it is a generic kernel api.
The arch specific kgdb.c for blackfin was cleaned of all functions
which exist in the kgdb core that do the same thing after resolving
the probe_kernel_read() and probe_kernel_write(). This also
eliminated the need for most of the #include's.
CC: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some archs such as blackfin, would like to have an arch specific
probe_kernel_read() and probe_kernel_write() implementation which can
fall back to the generic implementation if no special operations are
needed.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
As noticed by Dan Carpenter <error27@gmail.com>, update_nl_seq()
currently contains an out of bounds read of the seq_aft_nl array
when looking for the oldest sequence number position.
Fix it to only compare valid positions.
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
Fix remaining xattr locks acquired in reiserfs_xattr_set_handle()
while we are holding the reiserfs lock to avoid lock inversions.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
It is called LBDAF since 2.6.31.
impact:
without this change, on 32bit,
DRBD would wrongly claim to only support 2TiB devices.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Stanse found an unreachable statement in reiserfs_ioctl. There is a
if followed by error assignment and `break' with no braces. Add the
braces so that we don't break every time, but only in error case,
so that REISERFS_IOC_SETVERSION actually works when it returns no
error.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Reiserfs <reiserfs-devel@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
reiserfs_get_acl is usually not called under the reiserfs lock,
as it doesn't need it. But it happens when it is called by
reiserfs_acl_chmod(), which creates a dependency inversion against
the private xattr inodes mutexes for the given inode.
We need to call it without the reiserfs lock, especially since
it's unnecessary.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
For configurations where Synaptics hardware is present but the Synaptics
extensions support is not compiled in, the mouse is reprobed and a new
device is allocated on every suspend/resume.
During probe, psmouse_switch_protocol() calls psmouse_extensions() with
set_properties=1. This calls the dummy synaptics_init() which returns an
error code, instructing us not to use the synaptics extensions.
During resume, psmouse_reconnect() calls psmouse_extensions() with
set_properties=0, in which case call to synaptics_init() is bypassed and
PSMOUSE_SYNAPTICS is returned. Since the result is different from previous
attempt psmouse_reconnect() fails and full re-probe happens.
Fix this by tweaking the set_properties=0 codepath in psmouse_extensions()
to be more careful about offering PSMOUSE_SYNAPTICS extensions.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
