Rename _mv88e6xxx_vlan_init in _mv88e6xxx_vtu_new, eventually called
from a new _mv88e6xxx_vtu_get function, which abstracts the VTU GetNext
VID-1 trick to retrieve a single entry.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user explicitly requests VLAN filtering with something like:
# echo 1 > /sys/class/net/<bridge>/bridge/vlan_filtering
Switchdev propagates a SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING port
attribute.
Add support for it in the DSA layer with a new port_vlan_filtering
function to let drivers toggle 802.1Q filtering on user demand.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ppp_read() and ppp_poll() can be called concurrently with ppp_ioctl().
In this case, ppp_ioctl() might call ppp_ccp_closed(), which may update
ppp->flags while ppp_read() or ppp_poll() is reading it.
The update done by ppp_ccp_closed() isn't atomic due to the bit mask
operation ('ppp->flags &= ~(SC_CCP_OPEN | SC_CCP_UP)'), so concurrent
readers might get transient values.
Reading incorrect ppp->flags may disturb the 'ppp->flags & SC_LOOP_TRAFFIC'
test in ppp_read() and ppp_poll(), which in turn can lead to improper
decision on whether the PPP unit file is ready for reading or not.
Since ppp_ccp_closed() is protected by the Rx and Tx locks (with
ppp_lock()), taking the Rx lock is enough for ppp_read() and ppp_poll()
to guarantee that ppp_ccp_closed() won't update ppp->flags
concurrently.
The same reasoning applies to ppp->n_channels. The 'n_channels' field
can also be written to concurrently by ppp_ioctl() (through
ppp_connect_channel() or ppp_disconnect_channel()). These writes aren't
atomic (simple increment/decrement), but are protected by both the Rx
and Tx locks (like in the ppp->flags case). So holding the Rx lock
before reading ppp->n_channels also prevents concurrent writes.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
Introduce devlink interface and first drivers to use it
There a is need for some userspace API that would allow to expose things
that are not directly related to any device class like net_device of
ib_device, but rather chip-wide/switch-ASIC-wide stuff.
Use cases:
1) get/set of port type (Ethernet/InfiniBand)
2) setting up port splitters - split port into multiple ones and squash again,
enables usage of splitter cable
3) setting up shared buffers - shared among multiple ports within
one chip (work in progress)
4) configuration of switch wide properties - resources division etc - This will
allow to pass configuration that is unacceptable to be passed as
a module option.
First patch of this set introduces a new generic Netlink based interface,
called "devlink". It is similar to nl80211 model and it is heavily
influenced by it, including the API definition. The devlink introduction patch
implements use cases 1) and 2). Other 2 are in development atm and will
be addressed by follow-ups.
It is very convenient for drivers to use devlink, as you can see in other
patches in this set.
Counterpart for devlink is userspace tool for now called "dl". Command line
interface and outputs are derived from "ip" tool so it should be easy
for users to get used to it.
It is available here as a standalone tool for now:
https://github.com/jpirko/devlink
After this is merge in kernel, I will include the "dl" or "devlink" tool
into iproute2 toolset.
Port type setting example:
myhost:~$ dl help
Usage: dl [ OPTIONS ] OBJECT { COMMAND | help }
where OBJECT := { dev | port | monitor }
OPTIONS := { -v/--verbose }
myhost:~$ dl dev help
Usage: dl dev show [DEV]
myhost:~$ dl dev show
pci/0000:01:00.0
myhost:~$ dl port help
Usage: dl port show [DEV/PORT_INDEX]
Usage: dl port set DEV/PORT_INDEX [ type { eth | ib | auto} ]
Usage: dl port split DEV/PORT_INDEX count
Usage: dl port unsplit DEV/PORT_INDEX
myhost:~$ dl port show
pci/0000:01:00.0/1: type ib ibdev mlx4_0
pci/0000:01:00.0/2: type ib ibdev mlx4_0
myhost:~$ sudo dl port set pci/0000:01:00.0/1 type eth
myhost:~$ dl port show
pci/0000:01:00.0/1: type eth netdev ens4
pci/0000:01:00.0/2: type ib ibdev mlx4_0
myhost:~$ sudo dl port set ens4 type auto
myhost:~$ dl port show
pci/0000:01:00.0/1: type eth(auto) netdev ens4
pci/0000:01:00.0/2: type ib ibdev mlx4_0
Port splitting example:
myswitch:~$ sudo modprobe mlxsw_pci
myswitch:~$ dl port
pci/0000:03:00.0/1: type eth netdev eth0
pci/0000:03:00.0/3: type eth netdev eth1
pci/0000:03:00.0/5: type eth netdev eth2
...
pci/0000:03:00.0/63: type eth netdev eth31
myswitch:~$ sudo dl port split pci/0000:03:00.0/1 2 (or "sudo dl port split eth0 2")
myswitch:~$ dl port
pci/0000:03:00.0/3: type eth netdev eth1
pci/0000:03:00.0/5: type eth netdev eth2
...
pci/0000:03:00.0/63: type eth netdev eth31
pci/0000:03:00.0/1: type eth netdev eth0 split_group 16
pci/0000:03:00.0/2: type eth netdev eth32 split_group 16
myswitch:~$ sudo dl port unsplit pci/0000:03:00.0/1
myswitch:~$ dl port
pci/0000:03:00.0/3: type eth netdev eth1
pci/0000:03:00.0/5: type eth netdev eth2
pci/0000:03:00.0/63: type eth netdev eth31
pci/0000:03:00.0/1: type eth netdev eth0
v2->v3:
patch 1/9
-removed generated devlink index and name, use bus name and dev name as
a handle for all userspace originated commands. Along with that,
remove sysfs stub. Requested by Hannes Sowa.
patch 2/9
-add dev param to devlink_register (api change)
patch 4/9
-add dev param to devlink_register (api change)
patch 9/9
-set port's speed according to width fix by Ido
v1->v2:
patch 1/9
-removed no longer used "devlink_dev" helper
-fix couple of typos and misspells
patch 4/9:
-removed SET_NETDEV_DEV set to devlink dev
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to split or unsplit a port using the newly introduced
devlink ops.
Once split, the original netdev is destroyed and 2 or 4 others are
created, according to user configuration. The new ports are like any
other port, with the sole difference of supporting a lower maximum
speed. When unsplit, the reverse process takes place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting and unsplitting we'll destroy usable ports on the fly, so
mark them using a NULL pointer to indicate that their local port number
is free and can be re-used.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port netdevs are each associated with a different local port number
in the device. These local ports are grouped into groups of 4 (e.g.
(1-4), (5-8)) called clusters. The cluster constitutes the one of two
possible modules they can be mapped to. This mapping is board-specific
and done by the device's firmware during init.
When splitting a port by 4, the device requires us to first unmap all
the ports in the cluster and then map each to a single lane in the module
associated with the port netdev used as the handle for the operation.
This means that two port netdevs will disappear, as only 100Gb/s (4
lanes) ports can be split and we are guaranteed to have two of these
((1, 3), (5, 7) etc.) in a cluster.
When unsplit occurs we need to reinstantiate the two original 100Gb/s
ports and map each to its origianl module. Therefore, during driver init
store the initial local port to module mapping, so it can be used later
during unsplitting.
Note that a by 2 split doesn't require us to store the mapping, as we
only need to reinstantiate one port whose module is known.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting a port we replace it with 2 or 4 other ports. To be able
to do that we need to remove the original port netdev and unmap it from
its module. However, we first mark it as disabled, as active ports
cannot be unmapped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add middle layer in mlxsw core code to forward port split/unsplit calls
into specific ASIC drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, there has been an mlx4-specific sysfs file allowing user to
change port type to either Ethernet of InfiniBand. This is very
inconvenient.
Allow to expose the same ability to set port type in a generic way
using devlink interface.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
v2->v3:
-add dev param to devlink_register (api change)
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce devlink infrastructure for drivers to register and expose to
userspace via generic Netlink interface.
There are two basic objects defined:
devlink - one instance for every "parent device", for example switch ASIC
devlink port - one instance for every physical port of the device.
This initial portion implements basic get/dump of objects to userspace.
Also, port splitter and port type setting is implemented.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend says:
====================
tc software only
This adds a software only flag to tc but incorporates a bunch of comments
from the original attempt at this.
First instead of having the offload decision logic be embedded in cls_u32
I lifted into cls_pkt.h so it can be used anywhere and named the flag
TCA_CLS_FLAGS_SKIP_HW (Thanks Jiri ;)
In order to do this I put the flag defines in pkt_cls.h as well. However
it was suggested that perhaps these flags could be lifted into the
upper layer of TCA_ as well but I'm afraid this can not be done with
existing tc design as far as I can tell. The problem is the filters are
packed and unpacked in the classifier specific code and pushing the flags
through the high level doesn't seem easily doable. And we already have
this design where classifiers handle generic options such as actions and
policers. So I think adding one more thing here is OK as 'tc', et. al.
already know how to handle this type of thing.
====================
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the initial implementation the only way to stop a rule from being
inserted into the hardware table was via the device feature flag.
However this doesn't work well when working on an end host system
where packets are expect to hit both the hardware and software
datapaths.
For example we can imagine a rule that will match an IP address and
increment a field. If we install this rule in both hardware and
software we may increment the field twice. To date we have only
added support for the drop action so we have been able to ignore
these cases. But as we extend the action support we will hit this
example plus more such cases. Arguably these are not even corner
cases in many working systems these cases will be common.
To avoid forcing the driver to always abort (i.e. the above example)
this patch adds a flag to add a rule in software only. A careful
user can use this flag to build software and hardware datapaths
that work together. One example we have found particularly useful
is to use hardware resources to set the skb->mark on the skb when
the match may be expensive to run in software but a mark lookup
in a hash table is cheap. The idea here is hardware can do in one
lookup what the u32 classifier may need to traverse multiple lists
and hash tables to compute. The flag is only passed down on inserts.
On deletion to avoid stale references in hardware we always try
to remove a rule if it exists.
The flags field is part of the classifier specific options. Although
it is tempting to lift this into the generic structure doing this
proves difficult do to how the tc netlink attributes are implemented
along with how the dump/change routines are called. There is also
precedence for putting seemingly generic pieces in the specific
classifier options such as TCA_U32_POLICE, TCA_U32_ACT, etc. So
although not ideal I've left FLAGS in the u32 options as well as it
simplifies the code greatly and user space has already learned how
to manage these bits ala 'tc' tool.
Another thing if trying to update a rule we require the flags to
be unchanged. This is to force user space, software u32 and
the hardware u32 to keep in sync. Thanks to Simon Horman for
catching this case.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original series drivers would get offload requests for cls_u32
rules even if the feature bit is disabled. This meant the driver had
to do a boiler plate check on the feature bit before adding/deleting
the rule.
This patch lifts the check into the core code and removes it from the
driver specific case.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offload decision was originally very basic and tied to if the dev
implemented the appropriate ndo op hook. The next step is to allow
the user to more flexibly define if any paticular rule should be
offloaded or not. In order to have this logic in one function lift
the current check into a helper routine tc_should_offload().
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni says:
====================
bridge/ovs: avoid skb head copy on frame forwarding
Currently, while when an OVS or Linux bridge is used to forward frames towards
some tunnel device, a skb_head_copy() may occur if the ingress device do not
provide enough headroom for the tx encapsulation.
This patch series tries to address the issue implementing a new ndo operation to
allow the master device to control the headroom used when allocating the skb on
frame reception.
Said operation is used by the Linux bridge to notify the bridged ports of
needed_headroom changes, and similar bookkeeping and behaviour is also added to
openvswitch, on a per datapath basis.
Finally, the operation is implemented for veth and tun device, which give
performance improvement in the 6-12% range when forwarding frames from said
devices towards a vxlan tunnel.
v2:
- fix netdev_get_fwd_headroom() behaviour
- remove some code duplication with the netdev_set_rx_headroom() and
netdev_reset_rx_headroom() helpers
- handle headroom reset on [v]port removal/deletion
- initialize tun align to the old default value
v3:
- fix a comment typo
====================
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx headroom for veth dev is the peer device needed_headroom.
Avoid ping-pong updates setting the private flag IFF_PHONY_HEADROOM.
This avoids skb head reallocation when forwarding from a veth dev
towards a device adding some kind of encapsulation.
When transmitting frames below the MTU size towards a vxlan device,
this gives about 10% performance speed-up when OVS is used to connect
the veth and the vxlan device and a little more when using a
plain Linux bridge.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_set_rx_headroom controls the align value used by tun devices to
allocate skbs on frame reception.
When the xmit device adds a large encapsulation, this avoids an skb
head reallocation on forwarding.
The measured improvement when forwarding towards a vxlan dev with
frame size below the egress device MTU is as follow:
vxlan over ipv6, bridged: +6%
vxlan over ipv6, ovs: +7%
In case of ipv4 tunnels there is no improvement, since the tun
device default alignment provides enough headroom to avoid the skb
head reallocation.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements bookkeeping support to compute the maximum
headroom for all the devices in each datapath. When said value
changes, the underlying devs are notified via the
ndo_set_rx_headroom method.
This also increases the internal vports xmit performance.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On bridge needed_headroom changes, the enslaved devices are
notified via the ndo_set_rx_headroom method
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This method allows the controlling device (i.e. the bridge) to specify
additional headroom to be allocated for skb head on frame reception.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: updates for net-next.
Miscellaneous updates covering SRIOV, IRQ coalescing, firmware logging and
package version for net-next. Thanks.
v2: Updated description and added more comments for patch 1. Fixed
function parameters formatting for patch 4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is used to send NVM_FIND_DIR_ENTRY messages which can return error
if the entry is not found. This is normal and the error message will
cause unnecessary alarm, so silence it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function bnxt_do_send_msg() to do essentially the same thing
with an additional paramter to silence error response messages. All
current callers will set silent to false.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For everything to fit, we remove the PHY microcode version and replace it
with the firmware package version in the fw_version string.
Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use appropriate firmware request header structure to prepare the
firmware messages. This avoids the unnecessary conversion of the
fields to 32-bit fields. Add appropriate endian conversion when
printing out the message fields in dmesg so that they appear correct
in the log.
Reported-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch, we used a hardcoded value of 500 msec as the default
value for firmware message response timeout. For better portability with
future hardware or debug platforms, use the value provided by firmware in
the first response and store it for all susequent messages. Redefine the
macro HWRM_CMD_TIMEOUT to the stored value. Since we don't have the
value yet in the first message, use the 500 ms default if the stored value
is zero.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tx and rx rings don't share the same completion ring, tx coalescing
parameters can be set differently from the rx coalescing parameters.
Otherwise, use rx coalescing parameters on shared completion rings.
Adjust rx coalescing default values to lower interrupt rate.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to set all the coalescing parameters. The function can
be used later to set both rx and tx coalescing parameters.
v2: Fixed function parameters formatting requested by DaveM.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't convert these to internal hardware tick values before storing
them. This avoids the confusion of ethtool -c returning slightly
different values than the ones set using ethtool -C when we convert
hardware tick values back to micro seconds. Add better comments for
the hardware settings.
Also, rename the current set of coalescing fields with rx_ prefix.
The next patch will add support of tx coalescing values.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During remove_one() when SRIOV is enabled, the PF driver
should broadcast PF driver unload notification to all
VFs that are attached to VMs. Upon receiving the PF
driver unload notification, the VF driver should print
a warning message to message log. Certain operations on the
VF may not succeed after the PF has unloaded.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the VF to setup its own MAC address if the PF has not administratively
set it for the VF. To do that, we should always store the MAC address
from the firmware. There are 2 cases:
1. The MAC address is valid. This MAC address is assigned by the PF and
it needs to override the current VF MAC address.
2. The MAC address is zero. The VF will use a random MAC address by default.
By storing this 0 MAC address in the VF structure, it will allow the VF
user to change the MAC address later using ndo_set_mac_address() when
it sees that the stored MAC address is 0.
v2: Expanded descriptions and added more comments.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use list_move_tail() to move MAC address entry from list of pending
to list of active entries. Simple list_add_tail() leaves the entry
also in the first list, this leads to list corruption.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJW0AKVAAoJED07qiWsqSVqlwYH/1wxn03OA5V3zsp7zjt+4095
ToUY7RFlRB5zLNCWE3uz37pRsiDv4TcJ/VwgtMlkvskjdFmQQOveEhJYKx1PVq/C
l1hOcPRdvn9Ji7WQp5gQGlT4zymQWU0//6oQGx5MkuaLhRhLXoRSIaj5WDNya6Iy
AqVJhi3hMoYWiMuV2bkvSicPZ39OCtDejJbGL4D1u6wGvHje3emGtxNoIzx3dJ81
jBiE5aNRnC5c5jtz4veEVIRFhYndvfUGE5deDG2K7wgLt4IGE0zLZAuf4NgbpbV7
Xi/Nt5LCRYepol9AoI3qd1vuH8LK7YAFcyB2NCqcZbvsqo1RXsuLZWQExSpsmfc=
=634Q
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.6-20160226' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-02-26
this is a pull request of 3 patch for net-next/master.
There are two patches by Simon Horman, in which the device tree support
for the rcar_can driver is improved. One patch by me fixes the bad
coding style of the ems_usb driver which was introduced recently.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJW0ACIAAoJED07qiWsqSVqraYIALM+0BeB5V2g2kyjvsQS2Zah
1139UfEwVvb3djUhEvq68+zsXwPVrBdf2Kk8KgQxOzB3ctKRp8JtN7HPLWLXrgLw
WSFRhye/xUuPrUgiuwZ8cGR1QiBAuA/xRgFR8re7+pQ2nEzlx53neWolnjuesuWo
5MKoyPK7LSIgkZD7VteJklpScDQDqGcbc6w6pe1yg8gwQZoDycD1+Hqj4JKehqJN
J0W6puBL6urs9KtCzZRzMzEk09rH5BanQsAlCf4NkE0zvnPmtjptmsgRAo4rpAz3
6L6C+B1gph04eb+dXKsIRAVdN+kCHt1Sa7PlmfxXrY2hgVLvb+pXwJ6p3O6DRXE=
=L95V
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.5-20160226' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-02-26
this is a pull request of one patch for net.
The patch by Maximilain Schneider fixes a kfree() problem during disconnect in
the gs_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The OSS sequencer client tries to drain the pending events at
releasing. Unfortunately, as spotted by syzkaller fuzzer, this may
lead to an unkillable process state when the event has been queued at
the far future. Since the process being released can't be signaled
any longer, it remains and waits for the echo-back event in that far
future.
Back to history, the draining feature was implemented at the time we
misinterpreted POSIX definition for blocking file operation.
Actually, such a behavior is superfluous at release, and we should
just release the device as is instead of keeping it up forever.
This patch just removes the draining call that may block the release
for too long time unexpectedly.
BugLink: http://lkml.kernel.org/r/CACT4Y+Y4kD-aBGj37rf-xBw9bH3GMU6P+MYg4W1e-s-paVD2pg@mail.gmail.com
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We want the size of the struct, not of a pointer to it. To be future
proof, just dereference the pointer to get the desired type.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Pull sparc fixes from David Miller:
1) System call tracing doesn't handle register contents properly across
the trace. From Mike Frysinger.
2) Hook up copy_file_range
3) Build fix for 32-bit with newer tools.
4) New sun4v watchdog driver, from Wim Coekaerts.
5) Set context system call has to allow for servicable faults when we
flush the register windows to memory
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix sparc64_set_context stack handling.
sparc32: Add -Wa,-Av8 to KBUILD_CFLAGS.
Add sun4v_wdt watchdog driver
sparc: Fix system call tracing register handling.
sparc: Hook up copy_file_range syscall.
Commit 04b38d6012 ("vfs: pull btrfs clone API to vfs layer")
added a duplicated line (in cifsfs.c) which causes a sparse compile
warning.
Signed-off-by: Steve French <steve.french@primarydata.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
RTS/CTS needs to be enabled if the rate is a fallback rate *or* if it's
a dual-stream rate and the sta is in dynamic SMPS mode.
Cc: stable@vger.kernel.org
Fixes: a3ebb4e1b7 ("mac80211: minstrel_ht: handle peers in dynamic SMPS")
Reported-by: Matías Richart <mrichart@fing.edu.uy>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Public Action frames use special rules for how the BSSID field (Address
3) is set. A wildcard BSSID is used in cases where the transmitter and
recipient are not members of the same BSS. As such, we need to accept
Public Action frames with wildcard BSSID.
Commit db8e173245 ("mac80211: ignore frames between TDLS peers when
operating as AP") added a rule that drops Action frames to TDLS-peers
based on an Action frame having different DA (Address 1) and BSSID
(Address 3) values. This is not correct since it misses the possibility
of BSSID being a wildcard BSSID in which case the Address 1 would not
necessarily match.
Fix this by allowing mac80211 to accept wildcard BSSID in an Action
frame when in AP mode.
Fixes: db8e173245 ("mac80211: ignore frames between TDLS peers when operating as AP")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Plantronics DA45 does not support reading the sample rate which leads
to many lines of "cannot get freq at ep 0x4" and "cannot get freq at
ep 0x84". This patch adds the USB ID of the DA45 to quirks.c and
avoids those error messages.
Signed-off-by: Dennis Kadioglu <denk@post.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 0b2b093ad4.
Turns out the MOXA vendor driver was basically just a copy of the
ti_usb_3410_5052 driver. We don't want two drivers for the same chip
even if mxu11x0 had gotten some much needed clean up before merge. So
let's remove the mxu11x0 driver, add support for these Moxa devices to
the TI driver, and then clean that driver up instead.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for 0x1045 PID of Telit LE922.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Like a signal return, we should use synchronize_user_stack() rather
than flush_user_windows().
Reported-by: Ilya Malakhov <ilmalakhovthefirst@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Binutils used to be (erroneously) extremely permissive about
instruction usage. But that got fixed and if you don't properly tell
it to accept classes of instructions it will fail.
This uncovered a specs bug on sparc in gcc where it wouldn't pass the
proper options to binutils options.
Deal with this in the kernel build by adding -Wa,-Av8 to KBUILD_CFLAGS.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
