When the send skbuff reaches the end, nlmsg_put and friends returns
-EMSGSIZE but it is silently thrown away in ndo_fdb_dump. It is called
within a for_each_netdev loop and the first fdb entry of a following
netdev could fit in the remaining skbuff. This breaks the mechanism
of cb->args[0] and idx to keep track of the entries that are already
dumped, which results missing entries in bridge fdb show command.
Signed-off-by: Minoura Makoto <minoura@valinux.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2016-02-24
This series contains updates to e1000e, igb and igbvf.
Raanan provides updates for e1000e, first increases the ULP timer since it
now takes longer for the ULP exit to complete on Skylake. Fixes the
configuration of the internal hardware PHY clock gating mechanism, which was
causing packet loss due to mis configuring. Fixed additional ULP
configuration settings which were not being properly cleared after cable
connect in V-Pro capable systems. Added support for more i219 devices.
Takuma Ueba provides a fix for I210 where IPv6 autoconf test sometimes
fails due to DAD NS for link-local is not transmitted. To avoid this
issue, we need to wait until 1000BASE-T status register "Remote receiver
status OK".
Todd provides a patch to override EEPROM WoL settings for specific OEM
devices. Then renamed igb defines to be more generic, since the define
E1000_MRQC_ENABLE_RSS_4Q enables 4 and 8 queues depending on the part.
Roland Hii fixes an issue where only the half cycle time of less than or
equal to 70 millisecond uses the I210 clock output function. His patch
adds additional conditions when half cycle time is equal to 125 or 250 or
500 millisecond to use the clock output function.
Alex Duyck adds support for generic transmit checksums for igb and igbvf.
Jon Maxwell fixes an issues where customer applications are registering
and un-registering multicast addresses every few seconds which is leading
to many "Link is up" messages in the logs as a result of the
netif_carrier_off(netdev) in igbvf_msix_other(). So remove the
link is up message when registering multicast addresses.
Corinna Vinschen provides a fix for when switching off VLAN offloading on
i350, the VLAN interface becomes unusable.
Stefan Assmann updates the driver to use ndo_stop() instead of
dev_close() when running ethtool offline self test. Since dev_close()
causes IFF_UP to be cleared which will remove the interfaces routes
and some addresses.
v2: Dropped patches 6-10 in the original series. Patch 6-7 added support
for character device for AVB and based on community feedback, we do not
want to do this. Patches 8-10 provided fixes to the problematic code
added in patches 6 & 7. So all of them must go!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On reviewing the code I realized that GRE and UDP tunnels could cause a
kernel panic if we used GSO to segment a large UDP frame that was sent
through the tunnel with an outer checksum and hardware offloads were not
available.
In order to correct this we need to update the feature flags that are
passed to the skb_segment function so that in the event of UDP
fragmentation being requested for the inner header the segmentation
function will correctly generate the checksum for the payload if we cannot
segment the outer header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: l3mdev: Fix source address for unnumbered deployments
David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces. The use
case has the VRF device as the VRF local loopback with addresses and
interfaces enslaved without an address themselves. e.g,
ip addr add 9.9.9.9/32 dev lo
ip link set lo up
ip link add name vrf0 type vrf table 101
ip rule add oif vrf0 table 101
ip rule add iif vrf0 table 101
ip link set vrf0 up
ip addr add 10.0.0.3/32 dev vrf0
ip link add name dummy2 type dummy
ip link set dummy2 master vrf0 up
--> note dummy2 has no address - unnumbered device
ip route add 10.2.2.2/32 dev dummy2 table 101
ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02
ping to the 10.2.2.2 through the L3 domain:
$ ping -I vrf0 -c1 10.2.2.2
ping: Warning: source address might be selected on device other than vrf0.
PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.
picks up the wrong address -- the one from 'lo' not vrf0. And from tcpdump:
12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64
This patch series changes address selection to only consider devices in
the same L3 domain and to use the VRF device as the L3 domains loopback.
$ ping -I vrf0 -c1 10.2.2.2
PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.
From tcpdump:
12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64
Now the source address comes from vrf0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When selecting an address in context of a VRF, the vrf master should be
preferred for address selection. If it isn't, the user has a hard time
getting the system to select to their preference - the code will pick
the address off the first in-VRF interface it can find, which on a
router could well be a non-routable address.
Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
[dsa: Fixed comment style and removed extra blank link ]
Signed-off-by: David S. Miller <davem@davemloft.net>
David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces.
Relevant commands from his script:
ip addr add 9.9.9.9/32 dev lo
ip link set lo up
ip link add name vrf0 type vrf table 101
ip rule add oif vrf0 table 101
ip rule add iif vrf0 table 101
ip link set vrf0 up
ip addr add 10.0.0.3/32 dev vrf0
ip link add name dummy2 type dummy
ip link set dummy2 master vrf0 up
--> note dummy2 has no address - unnumbered device
ip route add 10.2.2.2/32 dev dummy2 table 101
ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02
tcpdump -ni dummy2 &
And using ping instead of his socat example:
$ ping -I vrf0 -c1 10.2.2.2
ping: Warning: source address might be selected on device other than vrf0.
PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.
>From tcpdump:
12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64
Note the source address is from lo and is not a VRF local address. With
this patch:
$ ping -I vrf0 -c1 10.2.2.2
PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.
>From tcpdump:
12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64
Now the source address comes from vrf0.
The ipv4 function for selecting source address takes a const argument.
Removing the const requires touching a lot of places, so instead
l3mdev_master_ifindex_rcu is changed to take a const argument and then
do the typecast to non-const as required by netdev_master_upper_dev_get_rcu.
This is similar to what l3mdev_fib_table_rcu does.
IPv6 for unnumbered interfaces appears to be selecting the addresses
properly.
Cc: David Lamparter <david@opensourcerouting.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dd006da216 ("arm64: mm: increase VA range of identity map") made
some changes to the memory mapping code to allow physical memory to reside
at an offset that exceeds the size of the virtual mapping.
However, since the size of the vmemmap area is proportional to the size of
the VA area, but it is populated relative to the physical space, we may
end up with the struct page array being mapped outside of the vmemmap
region. For instance, on my Seattle A0 box, I can see the following output
in the dmesg log.
vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
0xffffffbfc0000000 - 0xffffffbfd0000000 ( 256 MB actual)
We can fix this by deciding that the vmemmap region is not a projection of
the physical space, but of the virtual space above PAGE_OFFSET, i.e., the
linear region. This way, we are guaranteed that the vmemmap region is of
sufficient size, and we can even reduce the size by half.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull Ceph fixes from Sage Weil:
"There are two small messenger bug fixes and a log spam regression fix"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: don't spam dmesg with stray reply warnings
libceph: use the right footer size when skipping a message
libceph: don't bail early from try_read() when skipping a message
Things got calmed down for rc6, as it seems, and we have only a few
HD-audio fixes at this time: a fix for Skylake codec probe errors,
a fix for missing interrupt handling, and a few Dell and HP quirks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HCiU
-----END PGP SIGNATURE-----
Merge tag 'sound-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Things got calmed down for rc6, as it seems, and we have only a few
HD-audio fixes at this time: a fix for Skylake codec probe errors, a
fix for missing interrupt handling, and a few Dell and HP quirks"
* tag 'sound-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Loop interrupt handling until really cleared
ALSA: hda - Fix headset support and noise on HP EliteBook 755 G2
ALSA: hda - Fixup speaker pass-through control for nid 0x14 on ALC225
ALSA: hda - Fixing background noise on Dell Inspiron 3162
ALSA: hda - Apply clock gate workaround to Skylake, too
- Revert an ACPI core change related to IRQ management in PCI
that introduced code relying on the use of kmalloc() which
turned out to also run during early init when that's not
available yet and caused some systems to crash on boot for
this reason along with a cleanup on top of it (Rafael Wysocki).
- Prevent devfreq from flooding the kernel log with useless
messages on Tegra (which started to happen after some recent
changes in the devfreq core) by fixing the driver to follow
the documentation and the core's expectations in its ->target
callback (Tomeu Vizoso).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=SW0x
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are two reverts of recent PCI-related ACPI core changes (one of
which caused some systems to crash on boot and the other was a cleanup
on top of it) and a devfreq fix for Tegra.
Specifics:
- Revert an ACPI core change related to IRQ management in PCI that
introduced code relying on the use of kmalloc() which turned out to
also run during early init when that's not available yet and caused
some systems to crash on boot for this reason along with a cleanup
on top of it (Rafael Wysocki).
- Prevent devfreq from flooding the kernel log with useless messages
on Tegra (which started to happen after some recent changes in the
devfreq core) by fixing the driver to follow the documentation and
the core's expectations in its ->target callback (Tomeu Vizoso)"
* tag 'pm+acpi-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI, PCI, irq: remove interrupt count restriction"
Revert "ACPI / PCI: Simplify acpi_penalize_isa_irq()"
PM / devfreq: tegra: Set freq in rate callback
Commit 172b2386ed ("KVM: x86: fix missed hardware breakpoints",
2016-02-10) worked around a case where the debug registers are not loaded
correctly on preemption and on the first entry to KVM_RUN.
However, Xiao Guangrong pointed out that the root cause must be that
KVM_DEBUGREG_BP_ENABLED is not being set correctly. This can indeed
happen due to the lazy debug exit mechanism, which does not call
kvm_update_dr7. Fix it by replacing the existing loop (more or less
equivalent to kvm_update_dr0123) with calls to all the kvm_update_dr*
functions.
Cc: stable@vger.kernel.org # 4.1+
Fixes: 172b2386ed
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 27a4c827c3
fbcon: use the cursor blink interval provided by vt
two attempts have been made at fixing a possible hang caused by
cursor_timer_handler. That function registers a timer to be triggered at
"jiffies + fbcon_ops.cur_blink_jiffies".
A new case had been encountered during initialisation of clcd-pl11x:
fbcon_fb_registered
do_fbcon_takeover
-> do_register_con_driver
fbcon_startup
(A) add_cursor_timer (with cur_blink_jiffies = 0)
-> do_bind_con_driver
visual_init
fbcon_init
(B) cur_blink_jiffies = msecs_to_jiffies(vc->vc_cur_blink_ms);
If we take an softirq anywhere between A and B (and we do),
cursor_timer_handler executes indefinitely.
Instead of patching all possible paths that lead to this case one at a
time, fix the issue at the source and initialise cur_blink_jiffies to
200ms when allocating fbcon_ops. This was its default value before
aforesaid commit. fbcon_cursor or fbcon_init will refine this value
downstream.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Cc: <stable@vger.kernel.org> # v4.2
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Drivers that use the SSB sprom functionality typically 'select SSB_SPROM'
from Kconfig, but CONFIG_SSB_HOST_SOC misses this, which results in
a build failure unless at least one of the other drivers that selects
it is enabled:
drivers/built-in.o: In function `ssb_host_soc_get_invariants':
(.text+0x459494): undefined reference to `ssb_fill_sprom_with_fallback'
This adds the same select statement that is used elsewhere.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 541c9a84cd ("ssb: pick SoC invariants code from MIPS BCM47xx arch")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* We forgot to free the paging memory (Matti)
* Fix the frames in flight accounting (Liad)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hdNJ
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2016-02-25' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Two fixes for 4.5:
* We forgot to free the paging memory (Matti)
* Fix the frames in flight accounting (Liad)
This patch fixes the return value in a case which should never occur.
Instead returning "-EINVAL" we return LOWPAN_IPHC_DAM_00 which is
invalid on context based addresses. Also change the WARN_ON_ONCE to
WARN_ONCE which was suggested by Dan Carpenter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the interrupt handler of HD-audio driver assumes that no irq
update is needed while processing the irq. But in reality, it has
been confirmed that the HW irq is issued even during the irq
handling. Since we clear the irq status at the beginning, process the
interrupt, then exits from the handler, the lately issued interrupt is
left untouched without being properly processed.
This patch changes the interrupt handler code to loop over the
check-and-process. The handler tries repeatedly as long as the IRQ
status are turned on, and either stream or CORB/RIRB is handled.
For checking the stream handling, snd_hdac_bus_handle_stream_irq()
returns a value indicating the stream indices bits. Other than that,
the change is only in the irq handler itself.
Reported-by: Libin Yang <libin.yang@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Simply document new compatibility string.
As a previous patch adds a generic R-Car Gen2 compatibility string
there appears to be no need for a driver updates.
By documenting these compat stings they may be used in DTSs shipped, for
example as part of ROMs. They must be used in conjunction with the Gen2
fallback compat string. At this time there are no known differences between
the r8a779[234] IP blocks and that implemented by the driver for the Gen2
fallback compat string. Thus there is no need to update the driver as the
use of the Gen2 fallback compat string will activate the correct code in
the current driver while leaving the option for r8a779[234]-specific driver
code to be activated in an updated driver should the need arise.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add fallback compatibility string for R-Car Gen 1 and Gen2.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 1 and Gen 2. But beyond that its not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7779 is older than r8a7778 but that doesn't imply that the latter is a
descendant of the former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the coding style issues introduced in commit:
90cfde4658 can: ems_usb: Fix possible tx overflow
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
gs_destroy_candev() erroneously calls kfree() on a struct gs_can *, which is
allocated through alloc_candev() and should instead be freed using
free_candev() alone.
The inappropriate use of kfree() causes the kernel to hang when
gs_destroy_candev() is called.
Only the struct gs_usb * which is allocated through kzalloc() should be freed
using kfree() when the device is disconnected.
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When perf added a "reg" function to the function tracing event (not a
tracepoint), it caused that event to be displayed as a tracepoint and
could cause errors in tracepoint handling. That was solved by adding a
flag to ignore ftrace non-tracepoint events. But that flag was missed
when displaying events in available_events, which should only contain
tracepoint events.
This broke a documented way to enable all events with:
cat available_events > set_event
As the function non-tracepoint event would cause that to error out.
The commit here fixes that by having the available_events file not list
events that have the ignore flag set.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWzxLPAAoJEKKk/i67LK/8uAMH+gPedE1YbBmhFOgOEEyjADsV
AJ/XRkqHhNyjB5h05jvO9KeoaEL27E0unvRNIKFjeKoco1fqQ5USMXr1hdOpQKt6
X16478XGWiZI2w11Yp86UmhrzVFmRcCv1zSIhTFhidOIQVwu6aUSRA3DchaBXCez
nzQBgRUzsHLWhS1tRNtdnf6gRe6PSImjwmpyYETPzzatedAW4D1Xp+u+7z2uKXka
jJIaE90hYDCT08+6Q+QeD1RR2Uzh+E72ZhM5wCcnuwKd5BfxLcZs23PCIlZjX24k
Iu2hPeW1VVIN/mbqY04R4oAKRXJG8Wio8l1S5ldJTPReBCZLDK5N2O+LWPwIEIU=
=Ypbd
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v4.5-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Another small bug reported to me by Chunyu Hu.
When perf added a "reg" function to the function tracing event (not a
tracepoint), it caused that event to be displayed as a tracepoint and
could cause errors in tracepoint handling. That was solved by adding
a flag to ignore ftrace non-tracepoint events. But that flag was
missed when displaying events in available_events, which should only
contain tracepoint events.
This broke a documented way to enable all events with:
cat available_events > set_event
As the function non-tracepoint event would cause that to error out.
The commit here fixes that by having the available_events file not
list events that have the ignore flag set"
* tag 'trace-fixes-v4.5-rc5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix showing function event in available_events
- Fix per-vcpu vgic bitmap allocation
- Do not give copy random memory on MMIO read
- Fix GICv3 APR register restore order
KVM/x86 fixes:
- Fix ubsan warning
- Fix hardware breakpoints in a guest vs. preempt notifiers
- Fix Hurd
Generic:
- use __GFP_NOWARN together with GFP_NOWAIT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJWzsReAAoJEL/70l94x66DT6cH/3K/X/eciQIQTjLWKQ9BUhsN
+4WN+PX51GCvRZgoGgXXxTUzWVpSHNE7iD5FR/yqiUpC6lq+GWYKyQYBU6S2tw7N
QrzVFUAOIAExfzw4ztLz8pvIIwsF6EC2sA0DRZO85FWApO4P3BJN/1nBa+THJchH
6RamguztCjVSfboFwpulPzmgzJwIQ1ai+KoO1z/1ifrxjOHLytF5wn6UegPXIkc6
PAWG0b6w2ZnSwTNhEdsjzlcEANd/otwOoTlcft//KLuBkSS0GgU3vgxv7OXeSn67
+Wa9wWT/rU6M4Ol0noXcyr/kiF5629bQ4IyLK7YFgOUPFt4Tmg+A1ABGc92WJa4=
=/9Sf
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"KVM/ARM fixes:
- Fix per-vcpu vgic bitmap allocation
- Do not give copy random memory on MMIO read
- Fix GICv3 APR register restore order
KVM/x86 fixes:
- Fix ubsan warning
- Fix hardware breakpoints in a guest vs. preempt notifiers
- Fix Hurd
Generic:
- use __GFP_NOWARN together with GFP_NOWAIT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: MMU: fix ubsan index-out-of-range warning
arm64: KVM: vgic-v3: Restore ICH_APR0Rn_EL2 before ICH_APR1Rn_EL2
KVM: async_pf: do not warn on page allocation failures
KVM: x86: fix conversion of addresses to linear in 32-bit protected mode
KVM: x86: fix missed hardware breakpoints
arm/arm64: KVM: Feed initialized memory to MMIO accesses
KVM: arm/arm64: vgic: Ensure bitmaps are long enough
Pull s390 bugfixes from Martin Schwidefsky:
"Two critical bug fixes for the signal handling"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/fpu: signals vs. floating point control register
s390/compat: correct restore of high gprs on signal return
in case of unusually long writes to some system interfaces used by
mountd and other nfs support utilities.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ezck
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.5-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfix from Bruce Fields:
"One fix for a bug that could cause a NULL write past the end of a
buffer in case of unusually long writes to some system interfaces used
by mountd and other nfs support utilities"
* tag 'nfsd-4.5-1' of git://linux-nfs.org/~bfields/linux:
sunrpc/cache: fix off-by-one in qword_get()
David Decotigny says:
====================
new ETHTOOL_GLINKSETTINGS/SLINKSETTINGS API
History:
v9
- add 'link' in macro, struct and function names
- rename ethtool_link_ksettings::parent -> ::base
- remove un-needed mlx4 en_dbg_enabled() companion patch
- note: bitmap u32[] API patches were merged separately by Kan Liang
v8
- bitmap u32 API returns number of bits copied, unit tests updated
v7
- module_exit in test_bitmap
v6
- fix copy_from_user in user/kernel handshake
v5
note: please see v4 bullets for a question regarding bitmap.c
- minor fix to make allyesconfig/allmodconfig
v4
- removed typedef for link mode bitmaps
- moved bitmap<->u32[] conversion routines to bitmap.c . This is the
naive implementation. I have an endian-aware version that uses
memcpy/memset as much as possible, but I find it harder to follow
(see http://paste.ubuntu.com/13863722/). Please let me know if I
should use it instead.
- fixes suggested by Ben Hutchings
v3
- rebased v2 on top of latest net-next, minor checkpatch/printf %*pb
updates
v2
- keep return 0 in get_settings when successful, instead of
propagating positive result from driver's get_settings callback.
v1
- original submission
The main goal of this series is to support ethtool link mode masks
larger than 32 bits. It implements a new ioctl pair
(ETHTOOL_GLINKSETTINGS/SLINKSETTINGS), its associated callbacks
(get/set_link_ksettings) and a new struct ethtool_link_settings, which
should eventually replace legacy ethtool_cmd. Internally, the kernel
uses fixed length link mode masks defined at compilation time in
ethtool.h (for now: 31 bits), that can be increased by changing
__ETHTOOL_LINK_MODE_LAST in ethtool.h (absolute max is 4064 bits,
checked at compile time), and the user/kernel interface allows this
length to be arbitrary within 1..4064. This should allow some
flexibility without using too much heap/stack space, at the cost of a
small kernel/user handshake for the user to determine the sizes of
those bitmaps.
Along the way, I chose to drop in the new structure the 3 ethtool_cmd
fields marked "deprecated" (transceiver/maxrxpkt/maxtxpkt). They are
still available for old drivers via the (old) ETHTOOL_GSET/SSET API,
but are not available to drivers that switch to new API. Of those 3
fields, ethtool_cmd::transceiver seems to be still actively used by
several drivers, maybe we should not consider this field deprecated?
The 2 other fields are basically not used. This transition requires
some care in the way old and new ethtool talk to the kernel.
More technical details provided in the description for main patch. In
particular details about backward compatibility properties.
Some open questions:
- the kernel/interface multiplexes the "tell me the bitmap length"
handshake and the "give me the settings" inside the new
ETHTOOL_GLINKSETTINGS cmd. I was thinking of making this into 2
separate cmds: 1 cmd ETHTOOL_GKERNELPROPERTIES which would be
kernel-wide rather than device-specific, would return properties
like "length of the link mode bitmaps", and possibly others. And
ETHTOOL_GLINKSETTINGS would expect the proper bitmaps
- the link mode bitmaps are piggybacked at tail of the new struct
ethtool_link_settings. Since its user-visible definition does not
assume specific bitmap width, I am using a 0-length array as the
publicly visible placeholder. But then, the kernel needs to
specialize it (struct ethtool_link_ksettings) to specify its
current link mode masks. This means that kernel code is "littered"
with "ksettings->base.field" to access "field" inside
ethtool_settings:
+ I could use ethtool_link_settings everywhere (instead of a new
ethtool_ksettings) and an container_of accessor (or a plain cast)
to retrieve the link mode masks?
+ or: we could decide to make the link mode masks statically
bounded again, ie. make their width public, but larger than
current 32, and unchangeable forever. This would make everything
straightforward, but we might hit limits later, or have an
unneeded memory/stack usage for unused bits.
any preference?
- I foresee bugs where people use the legacy/deprecated SUPPORTED_x
macros instead of the new ETHTOOL_LINK_MODE_x_BIT enums in the new
get/set_link_ksettings callbacks. Not sure how to prevent problems
with this.
The only driver which was converted for now is mlx4. I am not
considering fcoe as fully converted, but I updated it a minima to be
able to remove __ethtool_get_settings, now known as
__ethtool_get_link_ksettings.
Tested with legacy and "future" ethtool on 64b x86 kernel and 32+64b
ethtool, and on a 32b x86 kernel + 32b ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines a new ETHTOOL_GLINKSETTINGS/SLINKSETTINGS API,
handled by the new get_link_ksettings/set_link_ksettings callbacks.
This API provides support for most legacy ethtool_cmd fields, adds
support for larger link mode masks (up to 4064 bits, variable length),
and removes ethtool_cmd deprecated
fields (transceiver/maxrxpkt/maxtxpkt).
This API is deprecating the legacy ETHTOOL_GSET/SSET API and provides
the following backward compatibility properties:
- legacy ethtool with legacy drivers: no change, still using the
get_settings/set_settings callbacks.
- legacy ethtool with new get/set_link_ksettings drivers: the new
driver callbacks are used, data internally converted to legacy
ethtool_cmd. ETHTOOL_GSET will return only the 1st 32b of each link
mode mask. ETHTOOL_SSET will fail if user tries to set the
ethtool_cmd deprecated fields to
non-0 (transceiver/maxrxpkt/maxtxpkt). A kernel warning is logged if
driver sets higher bits.
- future ethtool with legacy drivers: no change, still using the
get_settings/set_settings callbacks, internally converted to new data
structure. Deprecated fields (transceiver/maxrxpkt/maxtxpkt) will be
ignored and seen as 0 from user space. Note that that "future"
ethtool tool will not allow changes to these deprecated fields.
- future ethtool with new drivers: direct call to the new callbacks.
By "future" ethtool, what is meant is:
- query: first try ETHTOOL_GLINKSETTINGS, and revert to ETHTOOL_GSET if
fails
- set: query first and remember which of ETHTOOL_GLINKSETTINGS or
ETHTOOL_GSET was successful
+ if ETHTOOL_GLINKSETTINGS was successful, then change config with
ETHTOOL_SLINKSETTINGS. A failure there is final (do not try
ETHTOOL_SSET).
+ otherwise ETHTOOL_GSET was successful, change config with
ETHTOOL_SSET. A failure there is final (do not try
ETHTOOL_SLINKSETTINGS).
The interaction user/kernel via the new API requires a small
ETHTOOL_GLINKSETTINGS handshake first to agree on the length of the link
mode bitmaps. If kernel doesn't agree with user, it returns the bitmap
length it is expecting from user as a negative length (and cmd field is
0). When kernel and user agree, kernel returns valid info in all
fields (ie. link mode length > 0 and cmd is ETHTOOL_GLINKSETTINGS).
Data structure crossing user/kernel boundary is 32/64-bit
agnostic. Converted internally to a legal kernel bitmap.
The internal __ethtool_get_settings kernel helper will gradually be
replaced by __ethtool_get_link_ksettings by the time the first
"link_settings" drivers start to appear. So this patch doesn't change
it, it will be removed before it needs to be changed.
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm fixes from Dave Airlie:
"This is a bit larger than Id like, but I asked the Intel guys to pull
in some Skylake fixes in the possibly vain hope that Skylake might be
more functional now that I'm seeing production hardware shipping.
For i915, it's mostly the same patch in a few places, making sure the
hw doesn't turn off when we are programming it.
Apart from that are two nouveau fixes, one for a module defer bug, and
one for using nouveau on new Lenovo P50 models.
Then there are a bunch of AMDGPU fixes, one is a fix for v4.4 vblank
regressions, and some PM fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (26 commits)
drm/nouveau/disp/dp: ensure sink is powered up before attempting link training
drm/nouveau: platform: Fix deferred probe
drm/amdgpu: disable direct VM updates when vm_debug is set
amdgpu: fix NULL pointer dereference at tonga_check_states_equal
drm/i915/gen9: Verify and enforce dc6 state writes
drm/i915/gen9: Check for DC state mismatch
drm/radeon/pm: adjust display configuration after powerstate
drm/amdgpu/pm: adjust display configuration after powerstate
drm/amdgpu/pm: add some checks for PX
drm/amdgpu: fix locking in force performance level
drm/amdgpu/gfx8: fix priv reg interrupt enable
drm/i915/skl: Ensure HW is powered during DDB HW state readout
drm/i915/lvds: Ensure the HW is powered during HW state readout
drm/i915/hdmi: Ensure the HW is powered during HW state readout
drm/i915/dsi: Ensure the HW is powered during HW state readout
drm/i915/dp: Ensure the HW is powered during HW state readout
drm/i915: Ensure the HW is powered when accessing the CRC HW block
drm/i915/ddi: Ensure the HW is powered during HW state readout
drm/i915/crt: Ensure the HW is powered during HW state readout
drm/i915: Ensure the HW is powered during HW access in assert_pipe
...
This patch add the SO_CNX_ADVICE socket option (setsockopt only). The
purpose is to allow an application to give feedback to the kernel about
the quality of the network path for a connected socket. The value
argument indicates the type of quality report. For this initial patch
the only supported advice is a value of 1 which indicates "bad path,
please reroute"-- the action taken by the kernel is to call
dst_negative_advice which will attempt to choose a different ECMP route,
reset the TX hash for flow label and UDP source port in encapsulation,
etc.
This facility should be useful for connected UDP sockets where only the
application can provide any feedback about path quality. It could also
be useful for TCP applications that have additional knowledge about the
path outside of the normal TCP control loop.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull libnvdimm fixes from Dan Williams:
- Two fixes for compatibility with the ACPI 6.1 specification.
Without these fixes multi-interface DIMMs will fail to be probed, and
address range scrub commands to find memory errors will give results
that the kernel will mis-interpret. For multi-interface DIMMs Linux
will accept either the original 6.0 implementation or 6.1.
For address range scrub we'll only support 6.1 since ACPI formalized
this DSM differently than the original example [1] implemented in
v4.2. The expectation is that production systems will only ever ship
the ACPI 6.1 address range scrub command definition.
- The wider async address range scrub work targeting 4.6 discovered
that the original synchronous implementation in 4.5 is not sizing its
return buffer correctly.
- Arnd caught that my recent fix to the size of the pfn_t flags missed
updating the flags variable used in the pmem driver.
- Toshi found that we mishandle the memremap() return value in
devm_memremap().
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nvdimm: use 'u64' for pfn flags
devm_memremap: Fix error value when memremap failed
nfit: update address range scrub commands to the acpi 6.1 format
libnvdimm, tools/testing/nvdimm: fix 'ars_status' output buffer sizing
nfit: fix multi-interface dimm handling, acpi6.1 compatibility
Currently, all ipv6 addresses are flushed when the interface is configured
down, including global, static addresses:
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
inet6 2100:1::2/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
valid_lft forever preferred_lft forever
$ ip link set dev eth1 down
$ ip -6 addr show dev eth1
<< nothing; all addresses have been flushed>>
Add a new sysctl to make this behavior optional. The new setting defaults to
flush all addresses to maintain backwards compatibility. When the set global
addresses with no expire times are not flushed on an admin down. The sysctl
is per-interface or system-wide for all interfaces
$ sysctl -w net.ipv6.conf.eth1.keep_addr_on_down=1
or
$ sysctl -w net.ipv6.conf.all.keep_addr_on_down=1
Will keep addresses on eth1 on an admin down.
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
inet6 2100:1::2/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
valid_lft forever preferred_lft forever
$ ip link set dev eth1 down
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST> mtu 1500 state DOWN qlen 1000
inet6 2100:1::2/120 scope global tentative
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link tentative
valid_lft forever preferred_lft forever
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a regression fix for changed sysfs path of
bq27xxx_battery and update MAINTAINERS file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wLVt
-----END PGP SIGNATURE-----
Merge tag 'for-v4.5-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
"Add a regression fix for changed sysfs path of bq27xxx_battery and
update MAINTAINERS file"
* tag 'for-v4.5-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: bq27xxx_battery: Restore device name
MAINTAINERS: update bq27xxx driver
