SD/MMC card timeouts can be very high. So avoid busy-waiting,
using the scheduler. Calculate all timeouts in jiffies units,
because this will give us the correct sign when to involve
the scheduler.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some cards are not able to calculate a valid CRC16 value
for CID and CSD reads (CRC for 512 byte data blocks is OK).
By moving the CRC enable after the read of CID and CSD, these
cards can be used. This patch was tested with a faulty 8 GByte
takeMS Class 6 SDHC card. This patch was suggested by
Pierre Ossman.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Spurious IRQs seen on MMC after 2.6.29. Flush posted write in IRQ
handler.
The interrupt line is released by clearing the error status bits
in the MMCHS_STAT register, which must occur before the interrupt
handler returns to avoid unwanted irqs. Hence the need to flush
the posted write.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Tony Lindgen <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
DMA request source (RSSR) needs to be set only once (in probe).
DMA burst length (BLR) need to be set only in set_ios()
This cleans up imxmci_setup_data() and should make it a little
bit faster :)
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add __init __exit for appropriate probe and remove functions.
Conver to platform_driver_probe()
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Save the bit 17 state of the pages when freeing the page list, and
reswizzle them if necessary when rebinding the pages (in case they were
swapped out). Since we have userland with expectations that the swizzle
enums let it pread and pwrite contents accurately, we can't expose a new
swizzle enum for bit 17 (which it would have to GTT map to handle), so we
handle it down in pread and pwrite by swizzling the copy when bit 17 of the
page address is set.
Signed-off-by: Eric Anholt <eric@anholt.net>
Otherwise, the results of our read didn't show up when we were faulting in
the page being read into (as happened with a testcase reading into a big
stack area). Likely accounts for some conformance test failures.
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes all the checkpatch --file complaints about kernel/ptrace.c
and also removes an unused #include. I've verified that there are no
changes to the compiled code on x86_64.
Signed-off-by: Roland McGrath <roland@redhat.com>
[ Removed the parts that just split a line - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
6260a4b052 ("/proc/pid/maps: don't show
pgoff of pure ANON VMAs" had a typo.
fs/proc/task_nommu.c:138: error: 'struct vm_area_struct' has no member named 'pg_off'
distcc[21484] ERROR: compile fs/proc/task_nommu.c on sprygo/32 failed
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i915_gem_put_relocs_to_user returned an uninitialized value which
got returned to userspace. This caused libdrm in my setup to never
get out of a do{}while() loop retrying i915_gem_execbuffer.
result was hanging X, overheating of cpu and 2-3gb of logfile-spam.
This patch adresses the issue by
1. initializing vars in this file where necessary
2. correcting wrongly interpreted return values of copy_[from/to]_user
Signed-off-by: Florian Mickler <florian@mickler.org>
[anholt: cleanups of unnecessary changes, consistency in APIs]
Signed-off-by: Eric Anholt <eric@anholt.net>
At the same time, bring the action message closer to the usual format.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Currently we detect HDMI monitor by hardware detection, but if an HDMI-DVI
adapter is used to connect a DVI monitor, hardware detection will incorrectly
take monitor as HDMI. HDMI spec says any device containing IEEE registration
identifier will be treated as HDMI device. The patch intends to detect HDMI
monitor by drm_detect_hdmi_monitor function which follows that rule.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We create a debugfs node (i915_ringbuffer_data) to expose a hex dump
of the ring buffer itself. We also expose another debugfs node
(i915_ringbuffer_info) with information on the state (i.e. head, tail
addresses) of the ringbuffer.
For batchbuffer dumping, we look at the device's active_list, dumping
each object which has I915_GEM_DOMAIN_COMMAND in its read
domains. This is all exposed through the dri/i915_batchbuffers debugfs
file with a header for each object (giving the objects gtt_offset so
that it can be matched against the offset given in the
BATCH_BUFFER_START command.
Signed-off-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This does the same as commit 9e80d40773
(avoid starting a transaction when no block allocation is needed)
but for data=writeback mode of ext3. We also cleanup the data=ordered
case a bit to stick to coding style...
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Now that we have a distinction between WRITE_SYNC and WRITE_SYNC_PLUG,
use WRITE_SYNC_PLUG in __block_write_full_page() to avoid unplugging
the block device I/O queue between each page that gets flushed out.
Otherwise, when we run sync() or fsync() and we need to write out a
large number of pages, the block device queue will get unplugged
between for every page that is flushed out, which will be a pretty
serious performance regression caused by commit a64c8610.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Paul suggested we allow for data addresses to be recorded along with
the traditional IPs as power can provide these.
For now, only the software pagefault events provide data addresses,
but in the future power might as well for some events.
x86 doesn't seem capable of providing this atm.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090408130409.394816925@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move PERF_RECORD_TIME so that all the fixed length items come before
the variable length ones.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090408130409.307926436@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Similar to the mmap data stream, add one that tracks the task COMM field,
so that the userspace reporting knows what to call a task.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090408130409.127422406@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a few comments because I was forgetting what field what for what
functionality.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090408130409.036984214@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Push the PERF_EVENT_COUNTER_OVERFLOW bit into the misc field so that
we can have the full 32bit for PERF_RECORD_ bits.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090408130408.891867663@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Limit the size of each record to 64k (or should we count in multiples
of u64 and have a 512K limit?), this gives 16 bits or spare room in the
header, which we can use for misc bits, so as to not have to grow the
record with u64 every time we have a few bits to report.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090408130408.769271806@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We should not be updating ctx->time from NMI context, work around that.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090408130408.681326666@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now /proc/interrupts of tip tree has new counters:
PLT: Platform interrupts
Format change of output, as like that by commit:
commit 7a81d9a7da
x86: smarten /proc/interrupts output
should be applied to these new counters too.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <49C98DEA.8060208@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now /proc/interrupts of tip tree has new counters:
CNT: Performance counter interrupts
Format change of output, as like that by commit:
commit 7a81d9a7da
x86: smarten /proc/interrupts output
should be applied to these new counters too.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <49C98DEA.8060208@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
update_rlimit_cpu() tries to optimize out set_process_cpu_timer() in case
when we already have CPUCLOCK_PROF timer which should expire first. But it
uses cputime_lt() instead of cputime_gt().
Test case:
int main(void)
{
struct itimerval it = {
.it_value = { .tv_sec = 1000 },
};
assert(!setitimer(ITIMER_PROF, &it, NULL));
struct rlimit rl = {
.rlim_cur = 1,
.rlim_max = 1,
};
assert(!setrlimit(RLIMIT_CPU, &rl));
for (;;)
;
return 0;
}
Without this patch, the task is not killed as RLIMIT_CPU demands.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Peter Lojkin <ia6432@inbox.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: stable@kernel.org
LKML-Reference: <20090327000610.GA10108@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
See http://bugzilla.kernel.org/show_bug.cgi?id=12911
copy_signal() copies signal->rlim, but RLIMIT_CPU is "lost". Because
posix_cpu_timers_init_group() sets cputime_expires.prof_exp = 0 and thus
fastpath_timer_check() returns false unless we have other expired cpu timers.
Change copy_signal() to set cputime_expires.prof_exp if we have RLIMIT_CPU.
Also, set cputimer.running = 1 in that case. This is not strictly necessary,
but imho makes sense.
Reported-by: Peter Lojkin <ia6432@inbox.ru>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Peter Lojkin <ia6432@inbox.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: stable@kernel.org
LKML-Reference: <20090327000607.GA10104@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: restore old behavior
for flat and phys_flat
Signed-off-by: Yinhai Lu <yinghai@kernel.org.
LKML-Reference: <49DCBBF1.8080903@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter has become a co-maintainer of the scheduler during the last year,
and Robert has become inactive - update the MAINTAINERS entry.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix build problems with leds-gpio:
CC drivers/leds/leds-gpio.o
drivers/leds/leds-gpio.c: In function 'create_gpio_led':
drivers/leds/leds-gpio.c:85: warning: 'return' with no value, in function returning non-void
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Impact: build fix
Add Kconfig dependency on NUMA for enabling UV. Although it might
be possible to configure non-NUMA UV systems, they are unsupported
and not interesting. Much of the infrastructure for UV requires
NUMA support.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090403203942.GA20137@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
/sys/firmware/sgi_uv should only be created on uv systems.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20090403222423.GA28546@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 4aaf2fec71 (xsysace: make it
'struct hd_driveid'-free) converted the cf_id member of 'struct
ace_device' from a 'struct hd_driveid' to a u16 array. However,
references to the base of the structure were still using the '&'
operator. When the address was used with the ata_id_u32() macro, the
compiler used the size of the entire array instead of sizeof(u16) to
calculate the offset from the base address.
This patch removes the use of the '&' operator from all references of
cf_id to fix the bug and remove future confusion.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As we have already PIO 6 transfer mode supported in IDE layer, we can turn
it on in the driver.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: "Steve Wootton" <swootton@esi-estech.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make the case of flushing the drive's cache explicit.
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Simplify tf_read() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and factoring out the code that
deals with the high order bytes into ide_tf_readback() to be called from the
only two functions interested, ide_complete_cmd() and ide_dump_sector().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for
the method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Simplify tf_load() method, making it deal only with 'struct ide_taskfile' and
the validity flags that the upper layer passes, and moving the code that deals
with the high order bytes into the only function interested, do_rw_taskfile().
This should stop the needless code duplication in this method and so make
it about twice smaller than it was; along with simplifying the setup for the
method call, this should save both time and space...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use write_devctl() method to clear/set the HOB bit in tf_read() method.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move device register masking (and setting drive->select) out of tf_load() method
and into the only function that needs to use this code, do_rw_taskfile()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: fix whitespace error]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
