When restoring the GIC state (after a suspend/resume cycle,
for example), the driver directly writes the 'enabled' state
it has saved by accessing GICD_ISENABLERn, which performs
an OR operation between the value present in the register
and the value we write.
If whatever code that has run before we reentered the kernel
has enabled an interrupt that was previously disabled, we won't
restore that disabled state.
Making sure we first clear the register (by writting to
GICD_ICENABLERn) before restoring the enabled state.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1447701208-18150-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When booting a GIC/GICv3 based system, we have no idea what
state the firmware (or previous kernel in the case of kexec)
has left the GIC, and some interrupts may still be active.
In order to garantee that we have a clean state, make sure
the active bits are cleared at init time.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Russell King <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1447701208-18150-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
including ptrace.h brings a definition of BITS_PER_PAGE into device
drivers and cause a build warning in allmodconfig builds:
drivers/block/drbd/drbd_bitmap.c:482:0: warning: "BITS_PER_PAGE" redefined
#define BITS_PER_PAGE (1UL << (PAGE_SHIFT + 3))
This uses a slightly different way to express current_pt_regs()
that avoids the use of the header and gets away with the already
included asm/ptrace.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Including linux/acpi.h from asm/dma-mapping.h causes tons of compile-time
warnings, e.g.
drivers/isdn/mISDN/dsp_ecdis.h:43:0: warning: "FALSE" redefined
drivers/isdn/mISDN/dsp_ecdis.h:44:0: warning: "TRUE" redefined
drivers/net/fddi/skfp/h/targetos.h:62:0: warning: "TRUE" redefined
drivers/net/fddi/skfp/h/targetos.h:63:0: warning: "FALSE" redefined
However, it looks like the dependency should not even there as
I do not see why __generic_dma_ops() cares about whether we have
an ACPI based system or not.
The current behavior is to fall back to the global dma_ops when
a device has not set its own dma_ops, but only for DT based systems.
This seems dangerous, as a random device might have different
requirements regarding IOMMU or coherency, so we should really
never have that fallback and just forbid DMA when we have not
initialized DMA for a device.
This removes the global dma_ops variable and the special-casing
for ACPI, and just returns the dma ops that got set for the
device, or the dummy_dma_ops if none were present.
The original code has apparently been copied from arm32 where we
rely on it for ISA devices things like the floppy controller, but
we should have no such devices on ARM64.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[catalin.marinas@arm.com: removed acpi_disabled check in arch_setup_dma_ops()]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When booting a 64k pages kernel that is built with CONFIG_DEBUG_RODATA
and resides at an offset that is not a multiple of 512 MB, the rounding
that occurs in __map_memblock() and fixup_executable() results in
incorrect regions being mapped.
The following snippet from /sys/kernel/debug/kernel_page_tables shows
how, when the kernel is loaded 2 MB above the base of DRAM at 0x40000000,
the first 2 MB of memory (which may be inaccessible from non-secure EL1
or just reserved by the firmware) is inadvertently mapped into the end of
the module region.
---[ Modules start ]---
0xfffffdffffe00000-0xfffffe0000000000 2M RW NX ... UXN MEM/NORMAL
---[ Modules end ]---
---[ Kernel Mapping ]---
0xfffffe0000000000-0xfffffe0000090000 576K RW NX ... UXN MEM/NORMAL
0xfffffe0000090000-0xfffffe0000200000 1472K ro x ... UXN MEM/NORMAL
0xfffffe0000200000-0xfffffe0000800000 6M ro x ... UXN MEM/NORMAL
0xfffffe0000800000-0xfffffe0000810000 64K ro x ... UXN MEM/NORMAL
0xfffffe0000810000-0xfffffe0000a00000 1984K RW NX ... UXN MEM/NORMAL
0xfffffe0000a00000-0xfffffe00ffe00000 4084M RW NX ... UXN MEM/NORMAL
The same issue is likely to occur on 16k pages kernels whose load
address is not a multiple of 32 MB (i.e., SECTION_SIZE). So round to
SWAPPER_BLOCK_SIZE instead of SECTION_SIZE.
Fixes: da141706ae ("arm64: add better page protections to arm64")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
plane_mask should be cleared inside the retry loop, because it gets
reset on every retry. Without this fix the plane->fb refcounting might
get out of sync on retries, resulting in either leaked memory or
use-after-free.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: stable@vger.kernel.org #v4.3
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447237751-9663-3-git-send-email-maarten.lankhorst@ubuntu.com
legacy_cursor_update was being set in restore_fbdev_mode_atomic which was
probably unintended. Fix this by only setting it in the function that needs it.
This oversight was introduced in
commit bbb1e52402
Author: Rob Clark <robdclark@gmail.com>
Date: Tue Aug 25 15:35:58 2015 -0400
drm/fb-helper: atomic restore_fbdev_mode()...
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: checkpatch fix]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1447237751-9663-2-git-send-email-maarten.lankhorst@ubuntu.com
Let's not mix platform_data headers with the core headers. Instead, let's
create a subdir at linux/platform_data and move the headers to that
common place, adding it to MAINTAINERS.
The headers were moved with:
mkdir include/linux/platform_data/media/; git mv include/media/gpio-ir-recv.h include/media/ir-rx51.h include/media/mmp-camera.h include/media/omap1_camera.h include/media/omap4iss.h include/media/s5p_hdmi.h include/media/si4713.h include/media/sii9234.h include/media/smiapp.h include/media/soc_camera.h include/media/soc_camera_platform.h include/media/timb_radio.h include/media/timb_video.h include/linux/platform_data/media/
And the references fixed with this script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="media/"
DIRS="media/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Let's not mix headers used by the core with those headers that
are needed by some driver-specific interface header.
The headers used on drivers were manually moved using:
mkdir include/media/drv-intf/
git mv include/media/cx2341x.h include/media/cx25840.h \
include/media/exynos-fimc.h include/media/msp3400.h \
include/media/s3c_camif.h include/media/saa7146.h \
include/media/saa7146_vv.h include/media/sh_mobile_ceu.h \
include/media/sh_mobile_csi2.h include/media/sh_vou.h \
include/media/si476x.h include/media/soc_mediabus.h \
include/media/tea575x.h include/media/drv-intf/
And the references for those headers were corrected using:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="drv-intf/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Currently, include/media is messy, as it contains both the V4L2 core
headers and some driver-specific headers on the same place. That makes
harder to identify what core headers should be documented and what
headers belong to I2C drivers that are included only by bridge/main
drivers that would require the functions provided by them.
Let's move those i2c specific files to its own subdirectory.
The files to move were produced via the following script:
mkdir include/media/i2c
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/*/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
for i in include/media/*.h; do n=`basename $i`; (for j in $(git grep -l $n); do dirname $j; done)|sort|uniq|grep -ve '^.$' > list; num=$(wc -l list|cut -d' ' -f1); if [ $num == 1 ]; then if [ "`grep i2c list`" != "" ]; then git mv $i include/media/i2c; fi; fi; done
And the references corrected via this script:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="i2c/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Merged Sakari Ailus patch that moves smiapp.h to include/media/i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The file include/media/lirc.h describes a public interface and
should thus be a public header. See kernel bug
https://bugzilla.kernel.org/show_bug.cgi?id=75751 which has
a manpage describing the interface + an acknowledgment that this
info belongs to uapi.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 5240f4e68d ("[media] DocBook/media/Makefile: Avoid make htmldocs
to fail") introduced a mkdir which is always called through
install_media_images from the Documentation/DocBook/Makefile htmldocs rule.
If you run 'make htmldocs' more than once you get:
mkdir: cannot create directory ‘./Documentation/DocBook//media_api’:
File exists
Add -p to the mkdir to continue no matter if the dir already exists.
Signed-off-by: Graham Whaley <graham.whaley@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Improve the comments at the header, removing kernel-doc
tag from where it doesn't belong, grouping the legacy tuner
functions, and improving the text.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The get_state()/set_state and the corresponding data types
(struct tuner_state and enum tuner_param) are old DVB interfaces
that came from the DVBv3 time.
Nowadays, set_params() provide a better way to set the tuner
and demod parameters. So, no need to keep those legacy stuff,
as all drivers that were using it got converted.
With this patch, all kABI elements at dvb_frontend.h are now
documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is tricky to get rid of those ops here, as the stv0299 driver
wants to set frequency in separate from setting the bandwidth.
So, we use a small trick: we temporarely fill the cache with
0 for either frequency or bandwidth and add some logic at
set_params to only change the property(ies) that aren't zero.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those ops aren't used by any driver, with is weird. I suspect
that mantis_vb3030 driver were not working properly...
Anyway, now that the driver uses the set_parms, the DVB
frontend core should do the right thing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those callbacks are meant to be used only on some very specific
cases. There's absolutely no need to do that at tda8261, as
the only parameter that it allows to be set/get is the frequency.
So, use the standard get_params() and get_frequency() kABI
ops.
There's no need to touch at any bridge driver, as all interactions
are done via the macros at tda8261_cfg.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those two callbacks are the ones that should be used by normal
DVB frontend drivers.
Add support for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On tda665x, set_state only sets frequency. As the kABI for set_state
is meant to be used only on special cases, split the function
into two, in order to allow it to be latter used by a DVBv5
cache params logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The stb6100 driver has a struct tuner_state on its state
struct, that it is used only to store the bandwidth. Even so,
this struct is not really used, as every time the bandwidth
is get or set, it goes through the hardware.
So, get rid of that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several tuner_param values that aren't by any driver or core:
DVBFE_TUNER_TUNERSTEP
DVBFE_TUNER_IFFREQ
DVBFE_TUNER_REFCLOCK
DVBFE_TUNER_IQSENSE
DVBFE_TUNER_DUMMY
Several of those correspond to the values at the tuner_state
struct with is also only initialized by not used anyware:
u32 tunerstep;
u32 ifreq;
u32 refclock;
It doesn't make sense to keep anything at the kABI that it is
not used. So, get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As SEC tone and voltage could have changed during
suspend(), restore them to their previous values at
resume().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DocBook description of this header has two issues:
- It calls the Kernel ABI as API, instead of kABI;
- It mentions that the DVB frontend kABI is not described
within the document. As this will actually generate a
single DocBook, this is actually not true, now that
the documentation for the frontend was added.
So, fix both issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This header file provides the kABI functions used by the
Digital TV Frontend core support. Add a description for
this kABI, to add at the device_drivers Kernel DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Documents the most used functions at the Digital TV
kABI: dvb_frontend_register(), dvb_frontend_unregister()
and dvb_frontend_detach().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dvb_frontend_reinitialise() function is a special case
used by just one frontend. Document it, for completeness.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This function is used mainly at the DVB core, in order to provide
emulation for a legacy ioctl. The only current exception is
the stv0299 driver, with takes more than 8ms to switch voltage,
breaking the emulation for FE_DISHNETWORK_SEND_LEGACY_CMD.
Document that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While dax pmd mappings are functional in the nominal path they trigger
kernel crashes in the following paths:
BUG: unable to handle kernel paging request at ffffea0004098000
IP: [<ffffffff812362f7>] follow_trans_huge_pmd+0x117/0x3b0
[..]
Call Trace:
[<ffffffff811f6573>] follow_page_mask+0x2d3/0x380
[<ffffffff811f6708>] __get_user_pages+0xe8/0x6f0
[<ffffffff811f7045>] get_user_pages_unlocked+0x165/0x1e0
[<ffffffff8106f5b1>] get_user_pages_fast+0xa1/0x1b0
kernel BUG at arch/x86/mm/gup.c:131!
[..]
Call Trace:
[<ffffffff8106f34c>] gup_pud_range+0x1bc/0x220
[<ffffffff8106f634>] get_user_pages_fast+0x124/0x1b0
BUG: unable to handle kernel paging request at ffffea0004088000
IP: [<ffffffff81235f49>] copy_huge_pmd+0x159/0x350
[..]
Call Trace:
[<ffffffff811fad3c>] copy_page_range+0x34c/0x9f0
[<ffffffff810a0daf>] copy_process+0x1b7f/0x1e10
[<ffffffff810a11c1>] _do_fork+0x91/0x590
All of these paths are interpreting a dax pmd mapping as a transparent
huge page and making the assumption that the pfn is covered by the
memmap, i.e. that the pfn has an associated struct page. PTE mappings
do not suffer the same fate since they have the _PAGE_SPECIAL flag to
cause the gup path to fault. We can do something similar for the PMD
path, or otherwise defer pmd support for cases where a struct page is
available. For now, 4.4-rc and -stable need to disable dax pmd support
by default.
For development the "depends on BROKEN" line can be removed from
CONFIG_FS_DAX_PMD.
Cc: <stable@vger.kernel.org>
Cc: Jan Kara <jack@suse.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
fs/cachefiles/rdwr.c: In function ‘cachefiles_write_page’:
fs/cachefiles/rdwr.c:882: warning: ‘ret’ may be used uninitialized in
this function
If the jump to label "error" is taken, "ret" will indeed be
uninitialized, and random stack data may be printed by the debug code.
Fixes: 102f4d900c ("FS-Cache: Handle a write to the page immediately beyond the EOF marker")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The Broadcom NAND driver is used by many different groups at Broadcom
now, so use the same mailing-list we use for other areas of the kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Given that INTUOSHT < BAMBOO_PT
features->type >= INTUOSHT || features->type <= BAMBOO_PT
condition is always true, and therefore device_type is under certain
circumstances wrongly set with WACOM_DEVICETYPE_PAD bit set.
Fix the condition so that it actually represents the range as intended.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The acpi_ec_delete_query() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 3349fb64b2 (ACPI / SBS: Add 5 us delay to fix SBS
hangs on MacBook), since the delay introduced by it is not necessary
any more after commit add68d6aa9 (ACPI / SMBus: Fix boot stalls /
high CPU caused by reentrant code).
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the SBS initialisation, a reentrant call to wait_event_timeout()
causes an intermittent boot stall of several minutes usually following
the "Switching to clocksource tsc" message. Another symptom of this bug
is high CPU usage from programs (Firefox, upowerd) querying the battery
state. This is caused by:
1. drivers/acpi/sbshc.c wait_transaction_complete() calls
wait_event_timeout():
if (wait_event_timeout(hc->wait, smb_check_done(hc),
msecs_to_jiffies(timeout)))
2. ___wait_event sets task state to uninterruptible
3. ___wait_event calls the "condition" smb_check_done()
4. smb_check_done (sbshc.c) calls through to ec_read() in
drivers/acpi/ec.c
5. ec_guard() is reached which calls wait_event_timeout()
if (wait_event_timeout(ec->wait,
ec_transaction_completed(ec),
guard))
ie. wait_event_timeout() is being called again inside evaluation of
the previous wait_event_timeout() condition
5. The EC IRQ handler calls wake_up() and wakes up the sleeping task in
ec_guard()
6. The task is now in state running even though the wait "condition" is
still being evaluated
7. The "condition" check returns false so ___wait_event calls
schedule_timeout()
8. Since the task state is running, the scheduler immediately schedules
it again
9. This loop usually repeats for around 250 seconds even though the
original wait_event_timeout was only 1000ms.
The timeout is incorrect because each call to schedule_timeout()
usually returns immediately, taking less than 1ms, so the jiffies
timeout counter is not decremented. The task is now stuck in a
running state, and so is highly likely to be immediately
rescheduled, which takes less than a jiffy. The loop will never exit
if all schedule_timeout() calls take less than a jiffy.
Fix this by replacing SMBus reads in the wait_event_timeout condition
with checks of a boolean value that is updated by the EC query handler.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=107191
Link: https://lkml.org/lkml/2015/11/6/776
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that IP1000A chips are supported by dl2k driver, the buggy ipg
driver can be removed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.
This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.
Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180
MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.
Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that IRQ number passed to dev_pm_set_wake_irq() and
dev_pm_set_dedicated_wake_irq() is valid (not negative) before
accepting it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Otherwise debugging locked up processes isn't possible.
v2: rebased
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
the OUTMCAST stat is double incremented, getting bumped once in the mcast code
itself, and again in the common ip output path. Remove the mcast bump, as its
not needed
Validated by the reporter, with good results
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Claus Jensen <claus.jensen@microsemi.com>
CC: Claus Jensen <claus.jensen@microsemi.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases the crash is caused by nicvf_remove() being called from
outside. For example, if we try to feed the device to vfio after the
probe has failed for some reason. So, move the check to better place.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent flaw in the netdev feature setting resulted in warnings
like this one from VLAN interfaces:
WARNING: CPU: 1 PID: 4975 at net/core/dev.c:2419 skb_warn_bad_offload+0xbc/0xcb()
: caps=(0x00000000001b5820, 0x00000000001b5829) len=2782 data_len=0 gso_size=1348 gso_type=16 ip_summed=3
The ":" is supposed to be preceded by a driver name, but in this
case it is an empty string since the device has no parent.
There are many types of network devices without a parent. The
anonymous warnings for these devices can be hard to debug. Log
the network device name instead in these cases to assist further
debugging.
This is mostly similar to how __netdev_printk() handles orphan
devices.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case multiple writes to a unix stream socket race we could end up in a
situation where we pre-allocate a new skb for use in unix_stream_sendpage
but have to free it again in the locked section because another skb
has been appended meanwhile, which we must use. Accidentally we didn't
clear the pointer after consuming it and so we touched freed memory
while appending it to the sk_receive_queue. So, clear the pointer after
consuming the skb.
This bug has been found with syzkaller
(http://github.com/google/syzkaller) by Dmitry Vyukov.
Fixes: 869e7c6248 ("net: af_unix: implement stream sendpage support")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_fdb_dump always expects an index to be returned by the ndo_fdb_dump op,
but when CONFIG_NET_SWITCHDEV is off, it returns an error.
Fix that by returning the given unmodified idx.
A similar fix was 0890cf6cb6 ("switchdev: fix return value of
switchdev_port_fdb_dump in case of error") but for the CONFIG_NET_SWITCHDEV=y
case.
Fixes: 45d4122ca7 ("switchdev: add support for fdb add/del/dump via switchdev_port_obj ops.")
Signed-off-by: Dragos Tatulea <dragos@endocode.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
