I found that the current version of drivers/net/usb/dm9601.c can be used to
successfully drive a low-power, low-cost network adapter with USB ID
0a46:9000, based on a DM9000E chipset. As no device with this ID is yet
present in the kernel, I have created a patch that adds support for the device
to the dm9601 driver.
Created and tested against linux-2.6.32-rc5.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mailbox command process would only process a maximum of 5 unrelated
firmware events while waiting for it's command completion status.
It should process an unlimited number of events while waiting for a maximum of 5 seconds.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up driver resources without touch the hardware. Add pci
save/restore state.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Augment raw_send_hdrinc to correct for incorrect ip header length values
A series of oopses was reported to me recently. Apparently when using AF_RAW
sockets to send data to peers that were reachable via ipsec encapsulation,
people could panic or BUG halt their systems.
I've tracked the problem down to user space sending an invalid ip header over an
AF_RAW socket with IP_HDRINCL set to 1.
Basically what happens is that userspace sends down an ip frame that includes
only the header (no data), but sets the ip header ihl value to a large number,
one that is larger than the total amount of data passed to the sendmsg call. In
raw_send_hdrincl, we allocate an skb based on the size of the data in the msghdr
that was passed in, but assume the data is all valid. Later during ipsec
encapsulation, xfrm4_tranport_output moves the entire frame back in the skbuff
to provide headroom for the ipsec headers. During this operation, the
skb->transport_header is repointed to a spot computed by
skb->network_header + the ip header length (ihl). Since so little data was
passed in relative to the value of ihl provided by the raw socket, we point
transport header to an unknown location, resulting in various crashes.
This fix for this is pretty straightforward, simply validate the value of of
iph->ihl when sending over a raw socket. If (iph->ihl*4U) > user data buffer
size, drop the frame and return -EINVAL. I just confirmed this fixes the
reported crashes.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function-entry relative line number specifying support to
perf-probe. This allows users to define probes by line number
from entry of the function.
e.g.
perf probe schedule:16
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
LKML-Reference: <20091027204319.30545.30678.stgit@harusame>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This changes probe point syntax of perf-probe as below
<SRC>[:ABS_LN] [ARGS]
or
<FUNC>[+OFFS|%return][@SRC] [ARGS]
And event name and event group name are automatically
generated based on probe-symbol and offset as below.
perfprobes/SYMBOL_OFFSET[_NUM]
Where SYMBOL is the probing symbol and OFFSET is
the byte offset from the symbol.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
LKML-Reference: <20091027204310.30545.84984.stgit@harusame>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Exit searching after finding real (not-inlined) function,
because there should be no same symbol in that CU.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
LKML-Reference: <20091027204252.30545.19251.stgit@harusame>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix find_probe_event() to compare both of event-name and
event-group. Without this fix, kprobe-tracer overwrites existing
same event-name probe even if its group-name is different.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
LKML-Reference: <20091027204244.30545.27516.stgit@harusame>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add Intel AVX(Advanced Vector Extensions) instruction set
support to x86 instruction decoder. This adds insn.vex_prefix
field for storing VEX prefixes, and introduces some original
tags for expressing opcodes attributes.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
LKML-Reference: <20091027204226.30545.23451.stgit@harusame>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix superscripts position because some superscripts of SSE
opcode are not put in correct position.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
LKML-Reference: <20091027204204.30545.97296.stgit@harusame>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So that we can have a quicker start on perf top and even
speedups in the other tools, as we can have maps with no hits,
so no need to load its symtabs.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1256773881-4191-1-git-send-email-acme@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In mii monitor mode, bond_check_dev_link() calls the the ioctl
handler of slave devices. It stores the ndo_do_ioctl function
pointer to a static (!) ioctl variable and later uses it to call the
handler with the IOCTL macro.
If another thread executes bond_check_dev_link() at the same time
(even with a different bond, which none of the locks prevent), a
race condition occurs. If the two racing slaves have different
drivers, this may result in one driver's ioctl handler being
called with a pointer to a net_device controlled with a different
driver, resulting in unpredictable breakage.
Unless I am overlooking something, the "static" must be a
copy'n'paste error (?).
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
We create a dummy struct kernel_param on the stack for parsing each
array element, but we didn't initialize the flags word. This matters
for arrays of type "bool", where the flag indicates if it really is
an array of bools or unsigned int (old-style).
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
kp->arg is always true: it's the contents of that pointer we care about.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
e180a6b775 "param: fix charp parameters set via sysfs" fixed the case
where charp parameters written via sysfs were freed, leaving drivers
accessing random memory.
Unfortunately, storing a flag in the kparam struct was a bad idea: it's
rodata so setting it causes an oops on some archs. But that's not all:
1) module_param_array() on charp doesn't work reliably, since we use an
uninitialized temporary struct kernel_param.
2) there's a fundamental race if a module uses this parameter and then
it's changed: they will still access the old, freed, memory.
The simplest fix (ie. for 2.6.32) is to never free the memory. This
prevents all these problems, at cost of a memory leak. In practice, there
are only 18 places where a charp is writable via sysfs, and all are
root-only writable.
Reported-by: Takashi Iwai <tiwai@suse.de>
Cc: Sitsofe Wheeler <sitsofe@yahoo.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
On SMP guests, reads from the ring might bypass used index reads. This
causes guest crashes because host writes to used index to signal ring
data readiness. Fix this by inserting rmb before used ring reads.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Commit f68d24082e
in 2.6.32-rc1 broke requesting IRQs for per-VQ MSI-X vectors:
- vector number was used instead of the vector itself
- we try to request an IRQ for VQ which does not
have a callback handler
This is a regression that causes warnings in kernel log,
potentially lower performance as we need to scan vq list,
and might cause system failure if the interrupt
requested is in fact needed by another system.
This was not noticed earlier because in most cases
we were falling back on shared interrupt for all vqs.
The warnings often look like this:
virtio-pci 0000:00:03.0: irq 26 for MSI/MSI-X
virtio-pci 0000:00:03.0: irq 27 for MSI/MSI-X
virtio-pci 0000:00:03.0: irq 28 for MSI/MSI-X
IRQ handler type mismatch for IRQ 1
current handler: i8042
Pid: 2400, comm: modprobe Tainted: G W
2.6.32-rc3-11952-gf3ed8d8-dirty #1
Call Trace:
[<ffffffff81072aed>] ? __setup_irq+0x299/0x304
[<ffffffff81072ff3>] ? request_threaded_irq+0x144/0x1c1
[<ffffffff813455af>] ? vring_interrupt+0x0/0x30
[<ffffffff81346598>] ? vp_try_to_find_vqs+0x583/0x5c7
[<ffffffffa0015188>] ? skb_recv_done+0x0/0x34 [virtio_net]
[<ffffffff81346609>] ? vp_find_vqs+0x2d/0x83
[<ffffffff81345d00>] ? vp_get+0x3c/0x4e
[<ffffffffa0016373>] ? virtnet_probe+0x2f1/0x428 [virtio_net]
[<ffffffffa0015188>] ? skb_recv_done+0x0/0x34 [virtio_net]
[<ffffffffa00150d8>] ? skb_xmit_done+0x0/0x39 [virtio_net]
[<ffffffff8110ab92>] ? sysfs_do_create_link+0xcb/0x116
[<ffffffff81345cc2>] ? vp_get_status+0x14/0x16
[<ffffffff81345464>] ? virtio_dev_probe+0xa9/0xc8
[<ffffffff8122b11c>] ? driver_probe_device+0x8d/0x128
[<ffffffff8122b206>] ? __driver_attach+0x4f/0x6f
[<ffffffff8122b1b7>] ? __driver_attach+0x0/0x6f
[<ffffffff8122a9f9>] ? bus_for_each_dev+0x43/0x74
[<ffffffff8122a374>] ? bus_add_driver+0xea/0x22d
[<ffffffff8122b4a3>] ? driver_register+0xa7/0x111
[<ffffffffa001a000>] ? init+0x0/0xc [virtio_net]
[<ffffffff81009051>] ? do_one_initcall+0x50/0x148
[<ffffffff8106e117>] ? sys_init_module+0xc5/0x21a
[<ffffffff8100af02>] ? system_call_fastpath+0x16/0x1b
virtio-pci 0000:00:03.0: irq 26 for MSI/MSI-X
virtio-pci 0000:00:03.0: irq 27 for MSI/MSI-X
Reported-by: Marcelo Tosatti <mtosatti@redhat.com>
Reported-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The requeue_pi path doesn't use unqueue_me() (and the racy lock_ptr ==
NULL test) nor does it use the wake_list of futex_wake() which where
the reason for commit 41890f2 (futex: Handle spurious wake up)
See debugging discussing on LKML Message-ID: <4AD4080C.20703@us.ibm.com>
The changes in this fix to the wait_requeue_pi path were considered to
be a likely unecessary, but harmless safety net. But it turns out that
due to the fact that for unknown $@#!*( reasons EWOULDBLOCK is defined
as EAGAIN we built an endless loop in the code path which returns
correctly EWOULDBLOCK.
Spurious wakeups in wait_requeue_pi code path are unlikely so we do
the easy solution and return EWOULDBLOCK^WEAGAIN to user space and let
it deal with the spurious wakeup.
Cc: Darren Hart <dvhltc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: John Stultz <johnstul@linux.vnet.ibm.com>
Cc: Dinakar Guniguntala <dino@in.ibm.com>
LKML-Reference: <4AE23C74.1090502@us.ibm.com>
Cc: stable@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix sparse warning in arch/arm/mach-s3c2410/gpio.c due to missing
include of <mach/gpio-fns.h>. Fixes the following warning:
warning: symbol 's3c2410_gpio_irqfilter' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse warnings in arch/arm/mach-s3c2440/mach-mini2440.c
due to missing 'static'.
warning: symbol 'mini2440_lcd_cfg' was not declared. Should it be static?
warning: symbol 'mini2440_fb_info' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following warnings from sparse in arch/arm/plat-s3c24xx/gpio.
due to the missing include of <mach/gpio-fns.h>
gpio.c:36:6: warning: symbol 's3c2410_gpio_cfgpin' was not declared. Should it be static?
gpio.c:84:14: warning: symbol 's3c2410_gpio_getcfg' was not declared. Should it be static?
gpio.c:103:6: warning: symbol 's3c2410_gpio_pullup' was not declared. Should it be static?
gpio.c:125:5: warning: symbol 's3c2410_gpio_getpull' was not declared. Should it be static?
gpio.c:138:6: warning: symbol 's3c2410_gpio_setpin' was not declared. Should it be static?
gpio.c:157:14: warning: symbol 's3c2410_gpio_getpin' was not declared. Should it be static?
gpio.c:184:5: warning: symbol 's3c2410_gpio_getirq' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix missing select of S3C_DEV_USB_HOST when building for mini2440
only. Fixes the following error:
built-in.o: undefined reference to `s3c_device_usb`
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If the NULL test on buf is needed, then the dereference should be after the
NULL test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the export of s3c_adc_read.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
[ben-linux@fluff.org: remove unexport of s3c_adc_start, needed for ts]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the link errors if cpu-frequency support is enabled on s3c2410 systems
but there is no CONFIG_S3C2410_IOTIMING set. Fix this by ensuring the
relevant symbols are defined NULL if the code is not being built in.
Fixes the following error:
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_get'
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_set'
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_calc'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the S3C2442B CPU ID to aid support the Openmoko GTA02 / Freerunner.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: edit description for clarity and S3C2442B as uppercase]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define a macro to avoid the following error during kernel build process
for platforms other than s3c2410:
arch/arm/plat-s3c24xx/cpu.c:84: error: ‘s3c2410a_init’ undeclared here (not in a function)
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C64XX DMA implementation will work a lot better with the ability
to enqueue circular buffers as the hardware can do it's own linked-list
management.
Add a function s3c_dma_has_circular() to show that the system can do this
and a flag for the channel.
Update the s3c24xx/s3c64xx I2S DMA code to deal with this.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Mark Brown <broonie@@opensource.wolfsonmicro.com>
The function iommu_feature_disable is required on system
shutdown to disable the IOMMU but it is marked as __init.
This may result in a panic if the memory is reused. This
patch fixes this bug.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
proc.c and video.c are a bit sloppy around types and style,
confusing gcc for a new feature that'll be in 2.6.33 and will
cause a warning on the current code.
This patch changes
if (foo + 1 > sizeof bar)
into
if (foo >= sizeof(bar))
which is more kernel-style.
it also changes a variable in proc.c to unsigned; it gets assigned
a value from an unsigned type, and is then only compared for > not
for negative, so using unsigned is just outright the right type
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
pcpu_alloc() and pcpu_extend_area_map() perform a series of
spin_lock_irq()/spin_unlock_irq() calls, which make them unsafe
with respect to being called from contexts which have IRQs off.
This patch converts the code to perform save/restore of flags instead,
making pcpu_alloc() (or __alloc_percpu() respectively) to be called
from early kernel startup stage, where IRQs are off.
This is needed for proper initialization of per-cpu rq_weight data from
sched_init().
tj: added comment explaining why irqsave/restore is used in alloc path.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Tejun Heo <tj@kernel.org>
virtio net used to unlink skbs from send queues on error,
but ever since 48925e372f
we do not do this. This causes guest data corruption and crashes
with vhost since net core can requeue the skb or free it without
it being taken off the list.
This patch fixes this by queueing the skb after successful
transmit.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Page buffers containing packets with an incorrect checksum or using a
protocol not handled by hardware checksum offload were previously not
passed to LRO. The conversion to GRO changed this, but did not set
the ip_summed value accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BNX2_L2CTX_STATUSB_NUM definition needs to be changed to match
the recent firmware update:
commit 078b073588
bnx2: Update firmware to 5.0.0.j3.
Without the fix, bnx2 can crash intermittently in bnx2_rx_int() when
iSCSI is enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes suspend/resume on my rc410 motherboard, it restores
the memory controller setup before posting the GPU, since it seems
to need the MC_FB_LOCATION setup correctly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make sure we have an LVDS encoder before casting enc_priv.
[airlied: also fix two missing cpu_to_le16 casts we noticed on irc]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add some dummy symbols for the branches at 0xf00, 0xf20 and 0xf40,
otherwise hits end up in trap_0e which is confusing to the user.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If CONFIG_PPC_ISERIES isn't defined we end up with
iseries_check_pending_irqs and do_work at the same address.
perf ends up picking iseries_check_pending_irqs which creates
confusing backtraces. Hide it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A lot of hits in "setup" doesn't make much sense, so hide this symbol and
allow all the hits to end up in copy_4k_page.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
