AMD recently discovered that on some hardware, there is a race condition
possible when a C-state change request goes onto the bus at the same
time as a P-state change request.
Both requests happen, but the southbridge hardware only acknowledges the
C-state change. The PowerNow! driver is then stuck in a loop, waiting
for the P-state change acknowledgement. The driver eventually times
out, but can no longer perform P-state changes.
It turns out the solution is to resend the P-state change, which the
southbridge will acknowledge normally.
Thanks to Johannes Winkelmann for reporting this and testing the fix.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a stupid typo bug in the iSeries hash table code.
When we place a hash PTE in the secondary bucket, instead of setting the
SECONDARY flag bit, as we should, we (redundantly) set the VALID flag.
This was introduced with the patch abolishing bitfields from the hash
table code. Mea culpa, oops. It hasn't been noticed until now because
in practice we don't hit the secondary bucket terribly often.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The wrong state emission routines were being called for G550, and
consistent maps weren't correctly mapped...
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While working on 64K pages, I found this little buglet in our
update_mmu_cache() implementation.
The code calls __hash_page() passing it an "access" parameter (the type
of access that triggers the hash) containing the bits _PAGE_RW and
_PAGE_USER of the linux PTE. The latter is useless in this case and the
former is wrong. In fact, if we have a writeable PTE and we pass
_PAGE_RW to hash_page(), it will set _PAGE_DIRTY (since we track dirty
that way, by hash faulting !dirty) which is not what we want.
In fact, the correct fix is to always pass 0. That means that only
read-only or already dirty read write PTEs will be preloaded. The
(hopefully rare) case of a non dirty read write PTE can't be preloaded
this way, it will have to fault in hash_page on the actual access.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a typo in the div128_by_32 function used in the timekeeping
calculations on ppc64. If you look at the code it's quite obvious
that we need (rb + c) rather than (rb + b). The "b" is clearly just a
typo.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes handling of the phy identifiers in mptsas.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
[ split it a pre-2.6.14 portion from Eric's bigger patch ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Use GFP mask on TX skb allocation.
* Use the tx_headroom and reserve requested space.
Signed-off-by: Michael Buesch <mbuesch@freenet.de>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
The merge of syscalls.c & sys_ppc32.c (30286ef6e0)
broke mmap, if the mmap returned a 64 bit address.
do_mmap2 was taking the return value from do_mmap_pgoff (an unsigned long), and
storing it in an int, before returning it to sys_mmap as an unsigned long. So
we were losing the high bits of the address.
You would have thought the compiler could catch this for us ...
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch to make process.c work for 32-bit and 64-bit
(06d67d5474) broke some 64-bit binaries.
We were blowing away load_addr in gpr[2], so we weren't properly relocating
the entry point.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge ppc32 and ppc64 versions of thread_info.h. They were pretty
similar already, the chief changes are:
- Instead of inline asm to implement current_thread_info(),
which needs to be different for ppc32 and ppc64, we use C with an
asm("r1") register variable. gcc turns it into the same asm as we
used to have for both platforms.
- We replace ppc32's 'local_flags' with the ppc64
'syscall_noerror' field. The noerror flag was in fact the only thing
in the local_flags field anyway, so the ppc64 approach is simpler, and
means we only need a load-immediate/store instead of load/mask/store
when clearing the flag.
- In readiness for 64k pages, when THREAD_SIZE will be less
than a page, ppc64 used kmalloc() rather than get_free_pages() to
allocate the kernel stack. With this patch we do the same for ppc32,
since there's no strong reason not to.
- For ppc64, we no longer export THREAD_SHIFT and THREAD_SIZE
via asm-offsets, thread_info.h can now be safely included in asm, as
on ppc32.
Built and booted on G4 Powerbook (ARCH=ppc and ARCH=powerpc) and
Power5 (ARCH=ppc64 and ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the merge tree, commit 0458060c1c
broke boot on some machines because the initialization of conswitchp
was moved to arch/powerpc/kernel/setup_64.c, but a corresponding copy
was not added to arch/ppc64/kernel/setup.c. This patch fixes it.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
sata_qstor strays into a nasty area - gcc handling of wide enums is
full of bugs that got fixed between gcc versions creating portability
nightmare. Single-member enums are safe, so are ones that stay within
the range of int or unsigned int. Anything beyond that is asking for
trouble.
Declaration of constants split in two enums, taking the ~0UL one into
a separate enum.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Patch from Ben Dooks
From: Guillaume Gourat <guillaume.gourat@nexvision.fr>
Add MASK definitions for DCLK0 and DCLK1
Signed-off-by: Guillaume Gourat <guillaume.gourat@nexvision.fr>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The current Simtec BAST nand area timings are a little
too slow to be obtained by a 2410 running at 266MHz,
so reduce the timings slightly to bring them into the
acceptable range.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Avoid the possiblity that if the board is using
a 16.9334 or higher crystal with a high PLL
multiplier, then the pll value could overflow
the capability of an int.
Also fix the value types of the intermediate
variables to unsigned int.
Rewrite of patch from Guillaume Gourat
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Matt Reimer
Adds an I2S platform_device for PXA. I2S is used to interface
with sound chips on systems like iPAQ h1910/h2200/hx4700 and
Asus 716.
Signed-off-by: mreimer@vpop.net
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Improve sb1250-mac driver to probe for PHYs at addresses other
than 1, such as the PHYs on BigSur.
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff found an endian bug in the Marvell driver (thanks!). Here's the
fix for it.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add missing "break" in switch statement. Without the break, the
CM ended up always falling through and setting every connection
request to use RC transport, which meant that UC connections
didn't work.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It is legitimate to call tcp_fragment with len == skb->len since
that is done for FIN packets and the FIN flag counts as one byte.
So we should only check for the len > skb->len case.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Turns out the problem has nothing to do with use-after-free or double-free.
It's just that we're not clearing the CB area and DCCP unlike TCP uses a CB
format that's incompatible with IP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
icmp_send doesn't use skb->sk at all so even if skb->sk has already
been freed it can't cause crash there (it would've crashed somewhere
else first, e.g., ip_queue_xmit).
I found a double-free on an skb that could explain this though.
dccp_sendmsg and dccp_write_xmit are a little confused as to what
should free the packet when something goes wrong. Sometimes they
both go for the ball and end up in each other's way.
This patch makes dccp_write_xmit always free the packet no matter
what. This makes sense since dccp_transmit_skb which in turn comes
from the fact that ip_queue_xmit always frees the packet.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
David S. Miller <davem@davemloft.net> wrote:
> One thing you can probably do for this bug is to mark data packets
> explicitly somehow, perhaps in the SKB control block DCCP already
> uses for other data. Put some boolean in there, set it true for
> data packets. Then change the test in dccp_transmit_skb() as
> appropriate to test the boolean flag instead of "skb_cloned(skb)".
I agree. In fact we already have that flag, it's called skb->sk.
So here is patch to test that instead of skb_cloned().
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Without this patch, if you try and use a key that has not been
configured, for example:
% iwconfig eth1 key deadbeef00 [2]
without having configured key [1], then the active key will still be
[1], but privacy will now be enabled. Transmission of a packet in this
situation will result in a kernel oops.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
This reverts commit 3359b54c8c and
replaces it with a cleaner version that is purely based on page table
operations, so that the synchronization between inode size and hugetlb
mappings becomes moot.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Driver version, white space, comments, device id & other
Originally posted on 8/31 (and perhaps before)...I think it has not
been committed because the patch from that posting was damaged. I'm
reposting to make sure it gets in... :-)
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Include MII address 0 at the end of the PHY scan. This covers the
entire range of possible MII addresses.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
I had the sense of the test for when to use the old 601-style RTC
registers inverted. pmac_calibrate_decr and via_calibrate_decr
weren't setting ppc_tb_freq, on which all the further calculations
depended. Lastly, update_gtod was losing the top 32 bits of
the new tb_to_xs value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This declares powersave_nap in system.h and makes it an int everywhere,
fixes typos for the maple platform, fixes a couple of places where
I missed removing the last two arguments from a message_pass function,
and makes ppc64 consistent with ppc32 in the type of the
pci_bridge.cfg_data field.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously the individual xxx_calibrate_decr functions would each
print the timebase and cpu frequency and calculate several values
such as tb_to_us and tb_to_xs. This moves those printks and
calculations into time_init just after the call to the platform's
calibrate_decr function.
Signed-off-by: Paul Mackerras <paulus@samba.org>
