It's forbidden to manually change dev->features in run-time. Currently, this is
done in the driver to make sure that GSO_UDP_TUNNEL is advertized only when
VXLAN tunnel is set. However, since the stack actually does features intersection
with hw_enc_features, we can safely revert to advertizing features early when
registering the netdevice.
Fixes: f4a1edd561 ('net/mlx4_en: Advertize encapsulation offloads [...]')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
problem description:
The current code sets UAR page size equal to system page size.
The ConnectX-3 and ConnectX-3 Pro HWs require minimum 128 UAR pages.
The mlx4 kernel drivers are not loaded if there is less than 128 UAR pages.
solution:
Always set UAR page to 4KB. This allows more UAR pages if the OS
has PAGE_SIZE larger than 4KB. For example, PowerPC kernel use 64KB
system page size, with 4MB uar region, there are 4MB/2/64KB = 32
uars (half for uar, half for blueflame). This does not meet minimum 128
UAR pages requirement. With 4KB UAR page, there are 4MB/2/4KB = 512 uars
which meet the minimum requirement.
Note that only codes in mlx4_core that deal with firmware know that uar
page size is 4KB. Codes that deal with usr page in cq and qp context
(mlx4_ib, mlx4_en and part of mlx4_core) still have the same assumption
that uar page size equals to system page size.
Note that with this implementation, on 64KB system page size kernel, there
are 16 uars per system page but only one uars is used. The other 15
uars are ignored because of the above assumption.
Regarding SR-IOV, mlx4_core in hypervisor will set the uar page size
to 4KB and mlx4_core code in virtual OS will obtain the uar page size from
firmware.
Regarding backward compatibility in SR-IOV, if hypervisor has this new code,
the virtual OS must be updated. If hypervisor has old code, and the virtual
OS has this new code, the new code will be backward compatible with the
old code. If the uar size is big enough, this new code in VF continues to
work with 64 KB uar page size (on PowerPc kernel). If the uar size does not
meet 128 uars requirement, this new code not loaded in VF and print the same
error message as the old code in Hypervisor.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI channel could go offline during reset due to EEH. Don't bug on in
this case, the error is recoverable.
Fixes: f6bc11e426 ('net/mlx4_core: Enhance the catas flow to support device reset')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error flow in procedure handle_existing_counter() is wrong.
The procedure should exit after encountering the error, not continue
as if everything is OK.
Fixes: 68230242cd ('net/mlx4_core: Add port attribute when tracking counters')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the shift value used for time-stamping was constant and didn't
depend on the HW chip frequency. Change that to take the frequency into account
and calculate the maximal value in cycles per wraparound of ten seconds. This
time slot was chosen since it gives a good accuracy in time synchronization.
Algorithm for shift value calculation:
* Round up the maximal value in cycles to nearest power of two
* Calculate maximal multiplier by division of all 64 bits set
to above result
* Then, invert the function clocksource_khz2mult() to get the shift from
maximal mult value
Fixes: ec693d4701 ('net/mlx4_en: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RdropOvflw counts overrun of HW buffer, therefore should
be used for rx_fifo_errors only.
Currently RdropOvflw counter is mistakenly also set into
rx_missed_errors and rx_over_errors too, which makes the
device total dropped packets accounting to show wrong results.
Fix that. Use it for rx_fifo_errors only.
Fixes: c27a02cd94 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some NFSv4.1 OPEN requests were hanging waiting for the NFS server
to finish recalling delegations. Turns out that each NFSv4.1 CB
request on RDMA gets a GARBAGE_ARGS reply from the Linux client.
Commit 756b9b37cf added a line in bc_svc_process that
overwrites the incoming rq_rcv_buf's length with the value in
rq_private_buf.len. But rpcrdma_bc_receive_call() does not invoke
xprt_complete_bc_request(), thus rq_private_buf.len is not
initialized. svc_process_common() is invoked with a zero-length
RPC message, and fails.
Fixes: 756b9b37cf ('SUNRPC: Fix callback channel')
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Report that driver supports IB_PMA_CLASS_CAP_EXT_WIDTH in respond for
IB_MGMT_CLASS_PERF_MGMT mad with IB_PMA_CLASS_PORT_INFO attr id.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When attribute IB_PMA_PORT_COUNTERS_EXT is set, we now return 64 bit
values for the counters.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Today ocrdma driver defer arming the CQ till poll is called.
This was used to prevent calling poll-cq on an armed CQ.
Recently a set of new CQ API has been introduced into the linux
kernel. The implementation of this API guarantees that a given
CQ is never armed before calling poll on it. Most of the kernel
ULPs have already moved to use this new API or have a code where
poll is called before arming the CQ.
Thus, the above workaround in ocrdma is not needed anymore.
This patch removes the additional logic to deffer arm till poll
is called. This patch adds a simple scheme where ib_req_notify_cq()
will actually arm the cq.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Commit 754fe4a92c ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
introduces a problem setting the desired channel mode for the Mentor DMA
engine.
There is a case where an address is incorrectly assigned to the DMA
channel desired mode when it should instead be assigned the actual mode
value. This results in the value of channel->desired_mode not being
correct.
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Quite often drivers set only "write" permission assuming that this
includes "read" permission as well and this works on plenty of
platforms. However IODA2 is strict about this and produces an EEH when
"read" permission is not set and reading happens.
This adds a workaround in the IODA code to always add the "read" bit
when the "write" bit is set.
Fixes: 10b35b2b74 ("powerpc/powernv: Do not set "read" flag if direction==DMA_NONE")
Cc: stable@vger.kernel.org # 4.2+
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Tested-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch ensures that devices, which got registered before arch_initcall
will be handled correctly by IOMMU-based DMA-mapping code.
Cc: <stable@vger.kernel.org>
Fixes: 13b8629f65 ("arm64: Add IOMMU dma_ops")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Looks like g4x hpd live status bits actually agree with the spec. At
least they do on the machine I have, and apparently on Nick Bowler's
g4x as well.
So gm45 may be the only platform where they don't agree. At least
that seems to be the case based on the (somewhat incomplete)
logs/dumps in [1], and Daniel has also tested this on his gm45
sometime in the past.
So let's change the bits to match the spec on g4x. That actually makes
the g4x bits identical to vlv/chv so we can just share the code
between those platforms, leaving gm45 as the special case.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=52361
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Nick Bowler <nbowler@draconx.ca>
References: https://lists.freedesktop.org/archives/dri-devel/2016-February/100382.html
Reported-by: Nick Bowler <nbowler@draconx.ca>
Cc: stable@vger.kernel.org
Fixes: 237ed86c69 ("drm/i915: Check live status before reading edid")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455127145-20087-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 0780cd36c7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If CPU_UP_PREPARE is called it is not guaranteed, that a previously allocated
and assigned hash has been freed already, but perf_event_init_cpu()
unconditionally allocates and assignes a new hash if the swhash is referenced.
By overwriting the pointer the existing hash is not longer accessible.
Verify that there is no hash assigned on this cpu before allocating and
assigning a new one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20160209201007.843269966@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If CPU_DOWN_PREPARE fails the perf hotplug notifier is called for
CPU_DOWN_FAILED and calls perf_event_init_cpu(), which checks whether the
swhash is referenced. If yes it allocates a new hash and stores the pointer in
the per cpu data structure.
But at this point the cpu is still online, so there must be a valid hash
already. By overwriting the pointer the existing hash is not longer
accessible.
Remove the CPU_DOWN_FAILED state, as there is nothing to (re)allocate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20160209201007.763417379@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If CPU_UP_PREPARE fails the perf hotplug code calls perf_event_exit_cpu(),
which is a pointless exercise. The cpu is not online, so the smp function
calls return -ENXIO. So the result is a list walk to call noops.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20160209201007.682184765@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
CPU boot configuration writes to shmobile_boot_arg, which is located in
the .text section, and thus should not be written to.
As of commit 1d33a354bb ("ARM: shmobile: Per-CPU SMP boot / sleep
code for SCU SoCs"), and ignoring accidental remainings,
shmobile_boot_arg is always set to MPIDR_HWID_BITMASK by C code.
Hence we can just hardcode this in the assembler code, and remove the
variable, and thus also remove the need to write to this variable.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
If CONFIG_DEBUG_RODATA=y, the kernel crashes during system suspend:
Freezing user space processes ... (elapsed 0.004 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds)
done.
PM: suspend of devices complete after 111.948 msecs
PM: late suspend of devices complete after 1.086 msecs
PM: noirq suspend of devices complete after 11.576 msecs
Disabling non-boot CPUs ...
Kernel panic - not syncing: Attempted to kill the idle task!
1014ec ---[ end Kernel panic - not syncing: Attempted to kill the idle task!
CPU0: stopping
This happens because the .text section is marked read-only, while the
arrays shmobile_smp_mpidr[], shmobile_smp_fn[], and shmobile_smp_arg[]
are being written to.
Fix this by moving these arrays from the .text to the .bss section.
This requires accessing them through PC-relative offsets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 0ca2894b5a ("ARM: shmobile: Use shared SCU SMP boot code on
r8a7779") obsoleted the r8a7779-specific SCU boot code, but forgot to
remove the setup of shmobile_boot_fn and shmobile_boot_arg, which is
overwritten by shmobile_smp_scu_prepare_cpus().
Note that shmobile_scu_base wasn't initialized at that point yet anyway.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
shmobile_scu_base is being written to, so it doesn't belong in the .text
section. Fix this by moving it from asm .text to C .bss, as it's no
longer used from asm code since commit 4f6da36f7e ("ARM: shmobile:
Remove old SCU boot code").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Looks like the HPET spec at intel.com got moved.
It isn't hard to find so drop the link, just mention
the revision assumed.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/1455145462-3877-1-git-send-email-mst@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There will be data toggle error happen for full speed buld-out transfer.
The data toggle bit is saved in qh for non-control transfers, it is wrong
to check the qtd for that case.
Also fix one static analysis tool issue after fix the data toggle error.
John Youn:
* Added WARN() to warn on improper usage of the
dwc2_hcd_save_data_toggle() function.
Signed-off-by: Dyson Lee <dyson.lee@intel.com>
Signed-off-by: Tang, Jianqiang <jianqiang.tang@intel.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes memory manipulation issues and makes Host DDMA bulk transfers
work.
dwc2_process_non_isoc_desc() must return non zero value ONLY when
failure happens in one of the queued descriptors. After receiving
non zero value the caller must stop processing of remaining
QTDs and their descriptors from chain.
Commit 26a19ea699 ("usb: dwc2: host: fix use of qtd after
free in desc dma mode") breaks non_isoc transaction completion logic
in Host DDMA mode. There were bugs before that, but after this patch
dwc2_process_non_isoc_desc() returns fail status even if descriptor
was processed normally. This causes break from loop which is processing
remaining descriptors assigned to QTD, which is not correct for QTDs
containing more than one descriptor.
Current dwc2 driver gathers queued BULK URBs until receiving URB
without URB_NO_INTERRUPT flag. Once getting it, SW creates
descriptor chain, stores it in qh structure and passes start
address to HW. Multiple URB data is contained in that chain.
Hence on getting error on descriptor after its processing by HW,
SW should go out of both loops(qh->qtd, qtd->descs) and report
the failure.
Fixes: 26a19ea699 ("usb: dwc2: host: fix use of qtd after free in desc dma mode")
Cc: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes an issue found on rockchip rk3036 and rk3188 SOC platforms. For
some reason, the existing msleep(25) is not enough after the force mode.
The following patch was reported to fix the issue.
This does increase the probe delay again slightly, but not up to the
level it was before the original series of patches that this fixes. It
does not cause any other issues when tested on Synopsys HAPS and Altera
socfpga platforms.
Need to revisit this series next release to see if we can address these
issues without having an unconditional delay.
Fixes: 09c96980dc ("usb: dwc2: Add functions to set and clear force mode")
Reported-by: Caesar Wang <caesar.upstream@gmail.com>
Reported-by: Michael Niewoehner <linux@mniewoehner.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Caesar Wang <caesar.upstream@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Commit ca369d51b ("sd: Fix device-imposed transfer length limits")
introduced a new queue limit max_dev_sectors which limits the maximum
sectors for requests. The default value leads to small dasd requests
and therefor to a performance drop.
Set the max_dev_sectors value to the same value as the max_hw_sectors
to use the maximum available request size for DASD devices.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 4.4+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Data corruption issues were observed in tests which initiated
a system crash/reset while accessing BTT devices. This problem
is reproducible.
The BTT driver calls pmem_rw_bytes() to update data in pmem
devices. This interface calls __copy_user_nocache(), which
uses non-temporal stores so that the stores to pmem are
persistent.
__copy_user_nocache() uses non-temporal stores when a request
size is 8 bytes or larger (and is aligned by 8 bytes). The
BTT driver updates the BTT map table, which entry size is
4 bytes. Therefore, updates to the map table entries remain
cached, and are not written to pmem after a crash.
Change __copy_user_nocache() to use non-temporal store when
a request size is 4 bytes. The change extends the current
byte-copy path for a less-than-8-bytes request, and does not
add any overhead to the regular path.
Reported-and-tested-by: Micah Parrish <micah.parrish@hpe.com>
Reported-and-tested-by: Brian Boylston <brian.boylston@hpe.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: <stable@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: linux-nvdimm@lists.01.org
Link: http://lkml.kernel.org/r/1455225857-12039-3-git-send-email-toshi.kani@hpe.com
[ Small readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When fixing the DAT off bug ("s390: fix DAT off memory access, e.g.
on kdump") both Christian and I missed that we can save an additional
stnsm instruction.
This saves us a couple of cycles which could improve the speed of
memcpy_real.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the error path of amd_uncore_cpu_up_prepare() the newly allocated uncore
struct is freed, but the percpu pointer still references it. Set it to NULL.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1602162302170.19512@nanos
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The qxl_gem_prime_mmap() function returns ENOSYS instead of -ENOSYS
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the display resume path, move the calls to drm_vblank_on()
after the point when the display engine is running again.
Since changes were made to drm_update_vblank_count() in Linux 4.4+
to emulate hw vblank counters via vblank timestamping, the function
drm_vblank_on() now needs working high precision vblank timestamping
and therefore working scanout position queries at time of call.
These don't work before the display engine gets restarted, causing
miscalculation of vblank counter increments and thereby large forward
jumps in vblank count at display resume. These jumps can cause client
hangs on resume, or desktop hangs in the case of composited desktops.
Fix this Linux 4.4 regression by reordering calls accordingly.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: <stable@vger.kernel.org> # 4.4+
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: ville.syrjala@linux.intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_vblank_offdelay can have three different types of values:
< 0 is to be always treated the same as dev->vblank_disable_immediate
= 0 is to be treated as "never disable vblanks"
> 0 is to be treated as disable immediate if kms driver wants it
that way via dev->vblank_disable_immediate. Otherwise it is
a disable timeout in msecs.
This got broken in Linux 3.18+ for the implementation of
drm_vblank_on. If the user specified a value of zero which should
always reenable vblank irqs in this function, a kms driver could
override the users choice by setting vblank_disable_immediate
to true. This patch fixes the regression and keeps the user in
control.
v2: Only reenable vblank if there are clients left or the user
requested to "never disable vblanks" via offdelay 0. Enabling
vblanks even in the "delayed disable" case (offdelay > 0) was
specifically added by Ville in commit cd19e52aee
("drm: Kick start vblank interrupts at drm_vblank_on()"),
but after discussion it turns out that this was done by accident.
Citing Ville: "I think it just ended up as a mess due to changing
some of the semantics of offdelay<0 vs. offdelay==0 vs.
disable_immediate during the review of the series. So yeah, given
how drm_vblank_put() works now, I'd just make this check for
offdelay==0."
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # 3.18+
Cc: michel@daenzer.net
Cc: vbabka@suse.cz
Cc: ville.syrjala@linux.intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dri-devel@lists.freedesktop.org
Cc: alexander.deucher@amd.com
Cc: christian.koenig@amd.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Changes to drm_update_vblank_count() in Linux 4.4 broke the
behaviour of the pre/post modeset functions as the new update
code doesn't deal with hw vblank counter resets inbetween calls
to drm_vblank_pre_modeset an drm_vblank_post_modeset, as it
should.
This causes mistreatment of such hw counter resets as counter
wraparound, and thereby large forward jumps of the software
vblank counter which in turn cause vblank event dispatching
and vblank waits to fail/hang --> userspace clients hang.
This symptom was reported on radeon-kms to cause a infinite
hang of KDE Plasma 5 shell's login procedure, preventing users
from logging in.
Fix this by detecting when drm_update_vblank_count() is called
inside a pre->post modeset interval. If so, clamp valid vblank
increments to the safe values 0 and 1, pretty much restoring
the update behavior of the old update code of Linux 4.3 and
earlier. Also reset the last recorded hw vblank count at call
to drm_vblank_post_modeset() to be safe against hw that after
modesetting, dpms on etc. only fires its first vblank irq after
drm_vblank_post_modeset() was already called.
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> # 4.4+
Cc: michel@daenzer.net
Cc: vbabka@suse.cz
Cc: ville.syrjala@linux.intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dri-devel@lists.freedesktop.org
Cc: alexander.deucher@amd.com
Cc: christian.koenig@amd.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a regression introduced by the new drm_update_vblank_count()
implementation in Linux 4.4:
Restrict the bump of the software vblank counter in drm_update_vblank_count()
to a safe maximum value of +1 whenever there is the possibility that
concurrent readers of vblank timestamps could be active at the moment,
as the current implementation of the timestamp caching and updating is
not safe against concurrent readers for calls to store_vblank() with a
bump of anything but +1. A bump != 1 would very likely return corrupted
timestamps to userspace, because the same slot in the cache could
be concurrently written by store_vblank() and read by one of those
readers in a non-atomic fashion and without the read-retry logic
detecting this collision.
Concurrent readers can exist while drm_update_vblank_count() is called
from the drm_vblank_off() or drm_vblank_on() functions or other non-vblank-
irq callers. However, all those calls are happening with the vbl_lock
locked thereby preventing a drm_vblank_get(), so the vblank refcount
can't increase while drm_update_vblank_count() is executing. Therefore
a zero vblank refcount during execution of that function signals that
is safe for arbitrary counter bumps if called from outside vblank irq,
whereas a non-zero count is not safe.
Whenever the function is called from vblank irq, we have to assume concurrent
readers could show up any time during its execution, even if the refcount
is currently zero, as vblank irqs are usually only enabled due to the
presence of readers, and because when it is called from vblank irq it
can't hold the vbl_lock to protect it from sudden bumps in vblank refcount.
Therefore also restrict bumps to +1 when the function is called from vblank
irq.
Such bumps of more than +1 can happen at other times than reenabling
vblank irqs, e.g., when regular vblank interrupts get delayed by more
than 1 frame due to long held locks, long irq off periods, realtime
preemption on RT kernels, or system management interrupts.
A better solution would be to rewrite the timestamp caching to use
full seqlocks to allow concurrent writes and reads for arbitrary
vblank counter increments.
v2: Add code comment that this is essentially a hack and should
be replaced by a full seqlock implementation for caching of
timestamps.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # 4.4+
Cc: michel@daenzer.net
Cc: vbabka@suse.cz
Cc: ville.syrjala@linux.intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dri-devel@lists.freedesktop.org
Cc: alexander.deucher@amd.com
Cc: christian.koenig@amd.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise if a kms driver calls into drm_vblank_off() more than once
before calling drm_vblank_on() again, the redundant calls to
vblank_disable_and_save() will call drm_update_vblank_count()
while hw vblank counters and vblank timestamping are in a undefined
state during modesets, dpms off etc.
At least with the legacy drm helpers it is not unusual to
get multiple calls to drm_vblank_off and drm_vblank_on, e.g.,
half a dozen calls to drm_vblank_off and two calls to drm_vblank_on
were observed on radeon-kms during dpms-off -> dpms-on transition.
We don't no-op calls from atomic modesetting drivers, as they
should do a proper job of tracking hw state.
Fixes large jumps of the software maintained vblank counter due to
the hardware vblank counter resetting to zero during dpms off or
modeset, e.g., if radeon-kms is modified to use drm_vblank_off/on
instead of drm_vblank_pre/post_modeset().
This fixes a regression caused by the changes made to
drm_update_vblank_count() in Linux 4.4.
v2: Don't no-op on atomic modesetting drivers, per suggestion
of Daniel Vetter.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # 4.4+
Cc: michel@daenzer.net
Cc: vbabka@suse.cz
Cc: ville.syrjala@linux.intel.com
Cc: alexander.deucher@amd.com
Cc: christian.koenig@amd.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
This avoids integer overflows on 32bit machines when calculating
reloc_info size, as reported by Alan Cox.
Cc: stable@vger.kernel.org
Cc: gnomes@lxorguk.ukuu.org.uk
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Summary:
- fix compilation warnings on ARM64bit.
- fix mic driver initialization.
. MIC is a part of KMS so it converts it to use component framework
like other KMS drivers did.
- fix wrong driver state and disable clock order on DECON driver.
- fix incorrect use of dma_mmap_attrs function.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos/decon: fix disable clocks order
drm/exynos: fix incorrect cpu address for dma_mmap_attrs()
drm/exynos: exynos5433_decon: fix wrong state in decon_vblank_enable
drm/exynos: exynos5433_decon: fix wrong state assignment in decon_enable
drm/exynos: dsi: restore support for drm bridge
drm/exynos: mic: make all functions static
drm/exynos: mic: convert to component framework
drm/exynos: mic: use devm_clk interface
drm/exynos: fix types for compilation on 64bit architectures
drm/exynos: ipp: fix incorrect format specifiers in debug messages
drm/exynos: depend on ARCH_EXYNOS for DRM_EXYNOS
This reverts commit cfcfa086d4.
This causes the tiling properties to break in some unexpected ways,
Revert it for now.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
If tcp_v4_inbound_md5_hash() returns an error, we must release
the refcount on the request socket, not on the listener.
The bug was added for IPv4 only.
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inode struct members that track cgroup writeback information
should be reinitialized when inode gets allocated from
kmem_cache. Otherwise, their values remain and get used by the
new inode.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Fixes: d10c809552 ("writeback: implement foreign cgroup inode bdi_writeback switching")
Signed-off-by: Jens Axboe <axboe@fb.com>
There are some cases where rtt_us derives from deltas of jiffies,
instead of using usec timestamps.
Since we want to track minimal rtt, better to assume a delta of 0 jiffie
might be in fact be very close to 1 jiffie.
It is kind of sad jiffies_to_usecs(1) calls a function instead of simply
using a constant.
Fixes: f672258391 ("tcp: track min RTT using windowed min-filter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
