The pipestat fields affect reporting of all vblank-related interrupts, so we
have to reset them during the irq_handler, and while enabling vblank
interrupts. Otherwise, if a pipe status field had been set to non-zero
before enabling reporting, we would never see an interrupt again.
This patch adds i915_enable_pipestat and i915_disable_pipestat to abstract
out the steps needed to change the reported interrupts.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since commit c98451bd, the loop in nlm_lookup_host() unconditionally
compares the host's h_srcaddr field to the incoming source address.
For client-side nlm_host entries, both are always AF_UNSPEC, so this
check is unnecessary.
Since commit 781b61a6, which added support for AF_INET6 addresses to
nlm_cmp_addr(), nlm_cmp_addr() now returns FALSE for AF_UNSPEC
addresses, which causes nlm_lookup_host() to create a fresh nlm_host
entry every time it is called on the client.
These extra entries will eventually expire once the server is
unmounted, so the impact of this regression, introduced with lockd
IPv6 support in 2.6.28, should be minor.
We could fix this by adding an arm in nlm_cmp_addr() for AF_UNSPEC
addresses, but really, nlm_lookup_host() shouldn't be matching on the
srcaddr field for client-side nlm_host lookups.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
ml_ff_playback() uses spin_(un)lock_bh. However this function is
called with interrupts disabled from erase_effect() in
drivers/input/ff-core.c:196.
This is not permitted, and will result in a WARN_ON in the bottom
half handling code. This patch changes this function to just use
spin_lock_irqsave() instead, solving the problem and simplifying
the locking logic.
This was reported as entry #106559 in kerneloops.org
Reported-by: kerneloops.org
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Often we do things like put BUG() in the default clause of a case
statement. Since it was not declared __noreturn, this could sometimes
lead to bogus compiler warnings that variables were used
uninitialized.
There is a small problem in that we have to put a magic while(1); loop to
fool GCC into really thinking it is noreturn. This makes the new
BUG() function 3 instructions long instead of just 1, but I think it
is worth it as it is now unnecessary to do extra work to silence the
'used uninitialized' warnings.
I also re-wrote BUG_ON so that if it is given a constant condition, it
just does BUG() instead of loading a constant value in to a register
and testing it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The svc_addsock function adds transport instances without taking a
reference on the sunrpc.ko module, however, the generic transport
destruction code drops a reference when a transport instance
is destroyed.
Add a try_module_get call to the svc_addsock function for transport
instances added by this function.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Tested-by: Jeff Moyer <jmoyer@redhat.com>
If nfsd was shut down before the grace period ended, we could end up
with a freed object still on grace_list. Thanks to Jeff Moyer for
reporting the resulting list corruption warnings.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Tested-by: Jeff Moyer <jmoyer@redhat.com>
Since CLOCK_PROCESS_CPUTIME_ID is in fact translated to -6, the switch
statement in cpu_clock_sample_group() must first mask off the irrelevant
bits, similar to cpu_clock_sample().
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
--
posix-cpu-timers.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
New firmware image brings enhanced tuning performance.
Firmware is available for download at the following location:
http://www.steventoth.net/linux/sms1xxx
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video device was part of the gspca device. On device disconnection
while streaming, the device structure is freed at close time.
In this case, the remaining close job on the video device run out of
allocated memory.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous subdriver protection against rmmod was done via the
file operations table in the device descriptor. On device disconnection
while streaming, the device structure was freed at close time, and the
module_put still used the module name in the freed area.
Now, explicit module get/put are done on open and close.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a side effect, the sd routine stop0 is called on disconnect.
This permits the subdriver to free its resources.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
remove redundant argument comments in files of drivers/net/*
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: update documentation
Update to reflect the current state of the tracing framework:
- "none" tracer has been replaced by "nop" tracer
- tracing_enabled must be toggled when changing buffer size
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix mmiotrace overrun tracing
When ftrace framework moved to use the ring buffer facility, the buffer
overrun detection was broken after 2.6.27 by commit
| commit 3928a8a2d9
| Author: Steven Rostedt <rostedt@goodmis.org>
| Date: Mon Sep 29 23:02:41 2008 -0400
|
| ftrace: make work with new ring buffer
|
| This patch ports ftrace over to the new ring buffer.
The detection is now fixed by using the ring buffer API.
When mmiotrace detects a buffer overrun, it will report the number of
lost events. People reading an mmiotrace log must know if something was
missed, otherwise the data may not make sense.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: improve backtrace quality
avoid the confusion in call trace because of the lack of padding at the
tail of function.
When do_exit gets called, the return address behind call instruction is
pushed into stack. If something get wrong in do_exit, for x86_64, the
entry "kernel_execve +0x00/0xXX" rather than "child_rip +0xYY/0xZZ" is
in the call trace.
That looks confusing, so add a u2d to make the return address still part
of the original call site. (This also catches any instances of us returning
from that function somehow.)
Signed-off-by: jia zhang <jia.zhang2008@gmail.com>
Acked-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: make ENTRY()/END() macros more capable
It's usefull to catch unbalanced or messed or mixed declarations of ENTRY and
KPROBES. These macros would help a bit.
For example the following code would compile without problems
ENTRY_X86(mcount)
retq
END_X86(mcount)
But if you forget and mess the following form
ENTRY_X86(mcount)
retq
END(mcount)
ENTRY_X86(ftrace_caller)
The assembler will issue the following message:
Error: ENTRY_X86/KPROBE_X86 unbalanced,missed,mixed
Actually the checking is performed at every _X86 macro
so maybe it's good idea to put ENTRY_KPROBE_FINAL_X86
at the end of .S file to be sure you didn't miss anything.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Alexander van Heukelum <heukelum@mailshack.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
the use of is_blah() suggests a 1 or 0 return. This assumption is made in
pxa25x_udc code such as:
dev->vbus = is_vbus_present();
where dev->vbus is a bitfield. This fix allows pxa25x_udc_probe to correctly
detect vbus. Other changes were to make its use consistent in the rest of
the code.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During page sync, if a pagetable contains a self referencing pte (that
points to the pagetable), the corresponding spte may be marked as
writable even though all mappings are supposed to be write protected.
Fix by clearing page unsync before syncing individual sptes.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Impact: move some code out of .kprobes.text
KPROBE_ENTRY switches code generation to .kprobes.text, and KPROBE_END
uses .popsection to get back to the previous section (.text, normally).
Also replace ENDPROC by END, for consistency.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup of entry_64.S
Except for the order and the place of the functions, this
patch should not change the generated code.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
PAL_VPS_RESUME_HANDLER should use r26 to hold vac fields according to SDM.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use CFLAGS_vcpu.o, not EXTRA_CFLAGS, to provide fixed register information
to the compiler.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If an interrupt cannot be injected for some reason (say, page fault
when fetching the IDT descriptor), the interrupt is marked for
reinjection. However, if an NMI is queued at this time, the NMI
will be injected instead and the NMI will be lost.
Fix by deferring the NMI injection until the interrupt has been
injected successfully.
Analyzed by Jan Kiszka.
Signed-off-by: Avi Kivity <avi@redhat.com>
We can get an exit for instructions starting with 0xae, even if the guest is
in userspace. Lets make sure, that the signal processor handler is only called
in guest supervisor mode. Otherwise, send a program check.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Impact: cleanup
Move recently introduced dwarf2 macros to dwarf2.h file.
It allow us to not duplicate them in assembly files.
Active usage of _cfi macros don't make assembly files
more obvious to understand but we already have a lot of
macros there which requires to search the definitions
of them *anyway*. But at least it make every cfi usage
one line shorter.
Also some code alignment is done.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It causes recursive locking warning and is unneeded after
introduction of STARTED flag.
* Resume vs. stop is effectively solved by DISCONNECT flag.
* No problem in suspend vs. start -- urb is submitted even after open
which is possible after connect which is called after start.
* Resume vs. start solved by STARTED flag.
* Suspend vs. stop -- no problem in killing urb and timer twice.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Impact: fix MSIx not enough irq numbers available regression
The manual revert of the sparse_irq patches missed to bring the number
of possible irqs back to the .27 status. This resulted in a regression
when two multichannel network cards were placed in a system with only
one IO_APIC - causing the networking driver to not have the right
IRQ and the device not coming up.
Remove the dynamic allocation logic leftovers and simply return
NR_IRQS in probe_nr_irqs() for now.
Fixes: http://lkml.org/lkml/2008/11/19/354
Reported-by: Jesper Dangaard Brouer <hawk@diku.dk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jesper Dangaard Brouer <hawk@diku.dk>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Make the headers portion of signal_32.c and signal_64.c the same.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Simplify the irq-sampled stack overflow debug check:
- eliminate an #idef
- use WARN_ONCE() to emit a single warning (all bets are off
after the first such warning anyway)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: make stack overflow debug check and printout narrower
stack_overflow_check() should consider the stack usage of pt_regs, and
thus it could warn us in advance. Additionally, it looks better for
the warning time to start at INITIAL_JIFFIES.
Assuming that rsp gets close to the check point before interrupt
arrives: when interrupt really happens, thread_info will be partly
overrode.
Signed-off-by: jia zhang <jia.zhang2008@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The G3IPL expects the value at RAM address 0xa020b020 to be
exactly 1 to setup the bluetooth GPIOs properly. The actual
code got a value from gpio_get_value() which was not 1, but
a "not equal to 0" integer.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
In the resume bootstrap, the early disable address is wrong.
Fix it to RAM address 0xa020b000 instead of 0xa0200000, and
make it consistent with RESUME_ENABLE_ADDR in mioa701.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Impact: fix bootup crash
Even though it tested fine for me, there was still a bug in the
first patch: I have overlooked a call to ptregscall_common. This
patch fixes that, I think, but the code is never executed for
me while running a debian install... (I tested this by putting
an "1:jmp 1b" in there.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the slub allocator is used, kmem_cache_create() may merge two or more
kmem_cache's into one but the cache name pointer is not updated and
kmem_cache_name() is no longer guaranteed to return the pointer passed
to the former function. This patch stores the kmalloc'ed pointers in the
corresponding request_sock_ops and timewait_sock_ops structures.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=12014
Since most (if not all) implementations of TSO and even the in-kernel
software GSO do not update the urgent pointer when splitting a large
segment, it is necessary to turn off TSO/GSO for all outgoing traffic
with the URG pointer set.
Looking at tcp_current_mss (and the preceding comment) I even think
this was the original intention. However, this approach is insufficient,
because TSO/GSO is turned off only for newly created frames, not for
frames which were already pending at the arrival of a message with
MSG_OOB set. These frames were created when TSO/GSO was enabled,
so they may be large, and they will have the urgent pointer set
in tcp_transmit_skb().
With this patch, such large packets will be fragmented again before
going to the transmit routine.
As a side note, at least the following NICs are known to screw up
the urgent pointer in the TCP header when doing TSO:
Intel 82566MM (PCI ID 8086:1049)
Intel 82566DC (PCI ID 8086:104b)
Intel 82541GI (PCI ID 8086:1076)
Broadcom NetXtreme II BCM5708 (PCI ID 14e4:164c)
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix hp-plus driver link errors.
Builds as loadable module and kernel image driver.
All drivers that use 8390.o or 8390p.o that will build on
i386 with MCA/PCI/EISA/ISA were built successfully both
=m and =y.
drivers/built-in.o: In function `hpp_open':
hp-plus.c:(.text+0xac06c): undefined reference to `eip_interrupt'
hp-plus.c:(.text+0xac0d7): undefined reference to `eip_open'
drivers/built-in.o: In function `hpp_close':
hp-plus.c:(.text+0xac1bb): undefined reference to `eip_close'
drivers/built-in.o: In function `hpp_probe1':
hp-plus.c:(.init.text+0xa98a): undefined reference to `NS8390p_init'
drivers/built-in.o: In function `hp_plus_probe':
(.init.text+0xa9fe): undefined reference to `__alloc_eip_netdev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi,
after noticing that my Netgear FA411 (PCMCIA-NIC) [1] stopped working with
the release of the 2.6.25 kernel (sidux-version), I checked the
respective driver sources and noticed that the pcnet_cs driver bailed
out with "use axnet_cs instead" for the Netgear FA411, but axnet_cs
doesn't claim this ID.
I compiled a kernel with the PCMCIA-ID for the netgear card moved to
axnet_cs from pcnet_cs which worked. I then contacted sidux-kernel
maintainer Stefan Lippers-Hollmann who turned the info into this patch
and integrated it into the kernel:
<http://svn.berlios.de/svnroot/repos/fullstory/linux-sidux-2.6/trunk/debian/patches/features/2.6.27.4_PCMCIA_move-PCMCIA-ID-for-Netgear-FA411-from-pcnet_cs-to-axnet_cs.patch>
This works for me and AFAIK there were no reports of any breakage for
other devices on sidux-support.
This looks like a trivial patch, but since I have very limited
experience with kernel modifications I might be woefully wrong there.
But if there are no side effects of this patch, is it possible to get it
into the official kernel?
I can provide more detailed information on the affected hardware if
necessary.
-cord
[1]
Socket 1 Device 0: [axnet_cs] (bus ID: 1.0)
Configuration: state: on
Product Name: NETGEAR FA411 Fast Ethernet
Identification: manf_id: 0x0149 card_id: 0x0411
function: 6 (network)
prod_id(1): "NETGEAR" (0x9aa79dc3)
prod_id(2): "FA411" (0x40fad875)
prod_id(3): "Fast Ethernet" (0xb4be14e3)
prod_id(4): --- (---)
From: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Date: Sat, 1 Nov 2008 23:53:04 +0000
Subject: PCMCIA: move PCMCIA ID for Netgear FA411 from pcnet_cs to axnet_cs:
Since kernel 2.6.25, commit 61da96be07
(pcnet_cs: if AX88190-based card, printk "use axnet_cs instead" message.),
pcnet_cs bails out with "use axnet_cs instead" for the Netgear FA411, but
axnet_cs doesn't claim this ID.
Socket 1 Device 0: [axnet_cs] (bus ID: 1.0)
Configuration: state: on
Product Name: NETGEAR FA411 Fast Ethernet
Identification: manf_id: 0x0149 card_id: 0x0411
function: 6 (network)
prod_id(1): "NETGEAR" (0x9aa79dc3)
prod_id(2): "FA411" (0x40fad875)
prod_id(3): "Fast Ethernet" (0xb4be14e3)
prod_id(4): --- (---)
Cc: stable <stable@kernel.org> [2.6.25, 2.6.26, 2.6.27]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Cord Walter <qord@cwalter.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
