The first global-utilities node might not contain the rstcr
property, so we should search all the nodes
Signed-off-by: Matthew McClintock <msm@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There exists a four line chunk of code, which when configured for
64 bit address space, can incorrectly set certain page flags during
the TLB creation. It turns out that this is code which isn't used,
but might still serve a purpose. Since it isn't obvious why it exists
or why it causes problems, the below description covers both in detail.
For powerpc bootstrap, the physical memory (at most 768M), is mapped
into the kernel space via the following path:
MMU_init()
|
+ adjust_total_lowmem()
|
+ map_mem_in_cams()
|
+ settlbcam(i, virt, phys, cam_sz, PAGE_KERNEL_X, 0);
On settlbcam(), the kernel will create TLB entries according to the flag,
PAGE_KERNEL_X.
settlbcam()
{
...
TLBCAM[index].MAS1 = MAS1_VALID
| MAS1_IPROT | MAS1_TSIZE(tsize) | MAS1_TID(pid);
^
These entries cannot be invalidated by the
kernel since MAS1_IPROT is set on TLB property.
...
if (flags & _PAGE_USER) {
TLBCAM[index].MAS3 |= MAS3_UX | MAS3_UR;
TLBCAM[index].MAS3 |= ((flags & _PAGE_RW) ? MAS3_UW : 0);
}
For classic BookE (flags & _PAGE_USER) is 'zero' so it's fine.
But on boards like the the Freescale P4080, we want to support 36-bit
physical address on it. So the following options may be set:
CONFIG_FSL_BOOKE=y
CONFIG_PTE_64BIT=y
CONFIG_PHYS_64BIT=y
As a result, boards like the P4080 will introduce PTE format as Book3E.
As per the file: arch/powerpc/include/asm/pgtable-ppc32.h
* #elif defined(CONFIG_FSL_BOOKE) && defined(CONFIG_PTE_64BIT)
* #include <asm/pte-book3e.h>
So PAGE_KERNEL_X is __pgprot(_PAGE_BASE | _PAGE_KERNEL_RWX) and the
book3E version of _PAGE_KERNEL_RWX is defined with:
(_PAGE_BAP_SW | _PAGE_BAP_SR | _PAGE_DIRTY | _PAGE_BAP_SX)
Note the _PAGE_BAP_SR, which is also defined in the book3E _PAGE_USER:
#define _PAGE_USER (_PAGE_BAP_UR | _PAGE_BAP_SR) /* Can be read */
So the possibility exists to wrongly assign the user MAS3_U<RWX> bits
to kernel (PAGE_KERNEL_X) address space via the following code fragment:
if (flags & _PAGE_USER) {
TLBCAM[index].MAS3 |= MAS3_UX | MAS3_UR;
TLBCAM[index].MAS3 |= ((flags & _PAGE_RW) ? MAS3_UW : 0);
}
Here is a dump of the TLB info from Simics with the above code present:
------
L2 TLB1
GT SSS UUU V I
Row Logical Physical SS TLPID TID WIMGE XWR XWR F P V
----- ----------------- ------------------- -- ----- ----- ----- --- --- - - -
0 c0000000-cfffffff 000000000-00fffffff 00 0 0 M XWR XWR 0 1 1
1 d0000000-dfffffff 010000000-01fffffff 00 0 0 M XWR XWR 0 1 1
2 e0000000-efffffff 020000000-02fffffff 00 0 0 M XWR XWR 0 1 1
Actually this conditional code was used for two legacy functions:
1: support KGDB to set break point.
KGDB already dropped this; now uses its core write to set break point.
2: io_block_mapping() to create TLB in segmentation size (not PAGE_SIZE)
for device IO space.
This use case is also removed from the latest PowerPC kernel.
However, there may still be a use case for it in the future, like
large user pages, so we can't remove it entirely. As an alternative,
we match on all bits of _PAGE_USER instead of just any bits, so the
case where just _PAGE_BAP_SR is set can't sneak through.
With this done, the TLB appears without U having XWR as below:
-------
L2 TLB1
GT SSS UUU V I
Row Logical Physical SS TLPID TID WIMGE XWR XWR F P V
----- ----------------- ------------------- -- ----- ----- ----- --- --- - - -
0 c0000000-cfffffff 000000000-00fffffff 00 0 0 M XWR 0 1 1
1 d0000000-dfffffff 010000000-01fffffff 00 0 0 M XWR 0 1 1
2 e0000000-efffffff 020000000-02fffffff 00 0 0 M XWR 0 1 1
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for MPC8308 P1M board.
Supported devices:
DUART
Dual Ethernet
NOR flash
Both I2C controllers
USB in peripheral mode
PCI Express
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we do an mpic_reset_core we need to make sure the dcache is flushed.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make kexec_down_cpus atmoic since it will be incremented by all cores as
they are coming down.
Remove duplicate calls to mpc85xx_smp_kexec_down, now it's called by the
crash and normal kexec pathway only once.
Increase the timeout to wait for other cores to shutdown.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We no longer need to call this explicitly as a generic version is called
by default.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Right now just the kexec crash pathway turns turns off the interrupts.
Pull that out and make a generic version for use elsewhere
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Register the __init and __exit functions in the PowerPC Book-E Watchdog
driver as module entry/exit functions, and modify the Kconfig entry.
Add a .release method for the PowerPC Book-E Watchdog driver, so that the
watchdog is disabled when the driver is closed.
Loosely based on original code from Jiang Yutang <b14898@freescale.com>.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Export the global variable 'ppc_tb_freq', so that modules (like the Book-E
watchdog driver) can use it. To maintain consistency, ppc_proc_freq is
changed to a GPL-only export. This is okay, because any module that needs
this symbol should be an actual Linux driver, which must be GPL-licensed.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following commit broke 83xx because it assumed the 83xx platforms
exposed the "IMMR" address in BAR0 like the 85xx/86xx/QoriQ devices do:
commit 3da34aae03
Author: Kumar Gala <galak@kernel.crashing.org>
Date: Tue May 12 15:51:56 2009 -0500
powerpc/fsl: Support unique MSI addresses per PCIe Root Complex
However that is not true, so we have to search through the inbound
window settings on 83xx to find which one matches the IMMR address to
determine its PCI address.
Reported-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
bits_per_word option in spi_transfer are allowed if it does not change
the csr register.
This is necessary for the driver in
drivers/staging/iio/adis16260_core.c, as it uses this option.
Signed-off-by: Matthias Brugger <mensch0815@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch fixes the following build error introduced by commit
65308c46, "spi/topcliff: cleanup for style and conciseness".
drivers/spi/spi_topcliff_pch.c: In function 'pch_spi_process_messages':
drivers/spi/spi_topcliff_pch.c:752: warning: 'data' is used uninitialized in
+this function
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ring-buffer: Fix typo of time extends per page
perf, MIPS: Support cross compiling of tools/perf for MIPS
perf: Fix incorrect copy_from_user() usage
The SDK7786 FPGA has secondary control over the PCIe clocks, specifically
relating to the slots and oscillator. This ties the FPGA clocks in to the
clock framework and balances the refcounting similar to how the primary
on-chip clocks are managed. While the on-chip clocks are per-port, the
FPGA clock enable/disable is global for the entire block.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: relax ioremap prohibition (309caa9) for -final and -stable
ARM: 6440/1: ep93xx: DMA: fix channel_disable
cpuimx27: fix i2c bus selection
cpuimx27: fix compile when ULPI is selected
ARM: 6435/1: Fix HWCAP_TLS flag for ARM11MPCore/Cortex-A9
ARM: 6436/1: AT91: Fix power-saving in idle-mode on 926T processors
ARM: fix section mismatch warnings in Versatile Express
ARM: 6412/1: kprobes-decode: add support for MOVW instruction
ARM: 6419/1: mmu: Fix MT_MEMORY and MT_MEMORY_NONCACHED pte flags
ARM: 6416/1: errata: faulty hazard checking in the Store Buffer may lead to data corruption
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: iommu-load cam register before flushing the entry
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Silent spurious error message
drm/radeon/kms: fix bad cast/shift in evergreen.c
drm/radeon/kms: make TV/DFP table info less verbose
drm/radeon/kms: leave certain CP int bits enabled
drm/radeon/kms: avoid corner case issue with unmappable vram V2
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, numa: For each node, register the memory blocks actually used
x86, AMD, MCE thresholding: Fix the MCi_MISCj iteration order
x86, mce, therm_throt.c: Fix missing curly braces in error handling logic
Xen requires that all pages containing pagetable entries to be mapped
read-only. If pages used for the initial pagetable are already mapped
then we can change the mapping to RO. However, if they are initially
unmapped, we need to make sure that when they are later mapped, they
are also mapped RO.
We do this by knowing that the kernel pagetable memory is pre-allocated
in the range e820_table_start - e820_table_end, so any pfn within this
range should be mapped read-only. However, the pagetable setup code
early_ioremaps the pages to write their entries, so we must make sure
that mappings created in the early_ioremap fixmap area are mapped RW.
(Those mappings are removed before the pages are presented to Xen
as pagetable pages.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
LKML-Reference: <4CB63A80.8060702@goop.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Kbuild allows for us to probe for the existence of specific constructs
in the assembler, use them to find out if we can use fxsave64 and
permit the compiler to generate better code.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Commit 0793448 "DMAENGINE: generic channel status v2" changed the interface for
how dma channel progress is retrieved. It inadvertently exported an internal
helper function ioat_tx_status() instead of ioat_dma_tx_status(). The latter
polls the hardware to get the latest completion state, while the helper just
evaluates the current state without touching hardware. The effect is that we
end up waiting for completion timeouts or descriptor allocation errors before
the completion state is updated.
iperf (before fix):
[SUM] 0.0-41.3 sec 364 MBytes 73.9 Mbits/sec
iperf (after fix):
[SUM] 0.0- 4.5 sec 499 MBytes 940 Mbits/sec
This is a regression starting with 2.6.35.
Cc: <stable@kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Reported-by: Richard Scobie <richard@sauce.co.nz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
SDK7786 supports connecting either slot3 or 4 to the same PCIe port by
way of FPGA muxing. By default the vertical slot 3 on the baseboard is
enabled, so this adds in a command line option for forcibly enabling the
slot 4 edge connector.
If nothing has been specified on the command line, we fall back to
reading the resistor values for card presence to figure out where to
route the port to.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Updates to Phonet doc for Pipe controller 'connect' socket
implementation and changes related to socket options.
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on suggestion by Rémi Denis-Courmont to implement 'connect'
for Pipe controller logic, this patch implements 'connect' socket
call for the Pipe controller logic.
The patch does following:-
- Removes setsockopts for PNPIPE_CREATE and PNPIPE_DESTROY
- Adds setsockopt for setting the Pipe handle value
- Implements connect socket call
- Updates the Pipe controller logic
User-space should now follow below sequence with Pipe controller:-
-socket
-bind
-setsockopt for PNPIPE_PIPE_HANDLE
-connect
-setsockopt for PNPIPE_ENCAP_IP
-setsockopt for PNPIPE_ENABLE
GPRS/3G data has been tested working fine with this.
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all instances of legacy, or as yet to be implemented code
that is currently living within an #if 0 ... #endif block.
In the rare instance that some of it be needed in the future,
it can still be dragged out of history, but there is no need
for it to sit in mainline.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we set all skbs with CHECKSUM_UNNECESSARY, even
those whose protocol we don't know. This patch just
add the CHECKSUM_COMPLETE tag for non TCP/UDP packets.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit 43a9aa64a2 "NFSD:
Fill in WCC data for REMOVE, RMDIR, MKNOD, and MKDIR", we sometimes call
fh_unlock on a filehandle that isn't fully initialized.
We should fix up the callers, but as a quick fix it is also sufficient
just to remove this assertion.
Reported-by: Marius Tolzmann <tolzmann@molgen.mpg.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The ath_debug_stat_tx references bf->bf_mpdu, which
is the skb consumed by ath_tx_complete. So, call
the ath_debug_stat_tx method first.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like I submitted a different patch
than I tested, because clearly the code in
mac80211 is missing actually propagating the
requested SMPS mode. Fix that!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows mac80211 to enable receiving of Probe Request frames in
station mode which is needed for P2P.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the frame registration notification, we
can see when probe requests are requested and
notify the low-level driver via filtering. The
flag is also set in AP and IBSS modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers may need to adjust their filters according
to frame registrations, so notify them about them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix updates the documenation in Rate Control Table structure
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This automatically keeps things proper when wiphy
is renamed.
Based on patch by Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wext: fix alignment problem in serializing 'struct iw_point'
This fixes a typo in the definition of the serialized length of struct iw_point:
a) wireless.h is exported to userspace, the typo causes IW_EV_POINT_PK_LEN
to be 12 on 64-bit, and 8 on 32-bit systems (causing misalignment);
b) in compat-64 mode iwe_stream_add_point() memcpys overlap (see below).
The second case in in compat-64 mode looks like (variable names are as in
include/net/iw_handler.h:iwe_stream_add_point()):
point_len = IW_EV_COMPAT_POINT_LEN = 8
lcp_len = IW_EV_COMPAT_LCP_LEN = 4
2nd memcpy: IW_EV_POINT_PK_LEN - IW_EV_LCP_PK_LEN = 12 - 4 = 8
IW_EV_LCP_PK_LEN
<--------------> *---> 'extra' data area
+-------+-------+-------+-------+---------------+------- ...-+
| len | cmd |length | flags | (empty) -> extra ... |
+-------+-------+-------+-------+---------------+------- ...-+
2 2 2 2 4
lcp_len
<--------------> <-!! OVERLAP !!>
<--1st memcpy--><------- 2nd memcpy ----------->
<---- 3rd memcpy ------- ... >
<--------- point_len ---------->
This case could cause overrun whenever iw_point.length < 4.
The other two cases are -
* 32-bit systems: IW_EV_POINT_PK_LEN - IW_EV_LCP_PK_LEN = 8 - 4 = 4,
the second memcpy copies exactly the 4 required bytes;
* 64-bit systems: IW_EV_POINT_PK_LEN - IW_EV_LCP_PK_LEN = 12 - 4 = 8,
the second memcpy copies a superfluous (but non overlapping) 4 bytes.
The patch changes IW_EV_POINT_PK_LEN to be 8, so that in all 3 cases always only
the requested iw_point.{length,flags} (both __u16) are copied, avoiding overrrun
(compat-64) and superfluous copy (64-bit). In addition, the userspace header is
sanitized (in agreement with version 30 of the wireless tools).
Many thanks to Johannes Berg for help and review with this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ip_vs_dbg_callid() and IP_VS_DEBUG_CALLID() are only needed
it CONFIG_IP_VS_DEBUG is defined.
This resolves the following build warning when CONFIG_IP_VS_DEBUG is
not defined.
net/netfilter/ipvs/ip_vs_pe_sip.c:11: warning: 'ip_vs_dbg_callid' defined but not used
Reported-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Physical block size was declared unsigned int to accomodate the maximum
size reported by READ CAPACITY(16). Make sure we use the right type in
the related functions.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The upcoming XO-1 rfkill driver (for drivers/platform/x86) will register
itself with the name "xo1-rfkill", and the already-merged XO-1 poweroff
code uses name "olpc-xo1"
Add the necessary mechanics so that these devices are properly
initialized on XO-1 laptops.
Signed-off-by: Daniel Drake <dsd@laptop.org>
LKML-Reference: <20101013181042.90C8F9D401B@zog.reactivated.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This first converts the PMB locking over to raw spinlocks, and secondly
fixes up a nested locking issue that was triggering lockdep early on:
swapper/0 is trying to acquire lock:
(&pmbe->lock){......}, at: [<806be9bc>] pmb_init+0xf4/0x4dc
but task is already holding lock:
(&pmbe->lock){......}, at: [<806be98e>] pmb_init+0xc6/0x4dc
other info that might help us debug this:
1 lock held by swapper/0:
#0: (&pmbe->lock){......}, at: [<806be98e>] pmb_init+0xc6/0x4dc
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sdk7786 FPGA supports a number of user settable input switches that
are otherwise unused. This wires up a dummy gpio chip for the switch bank
to simply expose them to userspace.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
At least one board using the FEC driver does not have a conventional
PHY attached to it, it is directly connected to a somewhat simple
ethernet switch (the board is the SnapGear/LITE, and the attached
4-port ethernet switch is a RealTek RTL8305). This switch does not
present the usual register interface of a PHY, it presents nothing.
So a PHY scan will find nothing - it finds ID's of 0 for each PHY
on the attached MII bus.
After the FEC driver was changed to use phylib for supporting PHYs
it no longer works on this particular board/switch setup.
Add code support to use a fixed phy if no PHY is found on the MII bus.
This is based on the way the cpmac.c driver solved this same problem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many of the used macros are just there for userspace compatibility.
Substitute the in-kernel code to directly use the terminal macro
and stuff the defines into #ifndef __KERNEL__ sections.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Fix
kernel/trace/trace_functions_graph.c: In function ‘trace_print_graph_duration’:
kernel/trace/trace_functions_graph.c:652: warning: comparison of distinct pointer types lacks a cast
when building 36-rc6 on a 32-bit due to the strict type check failing
in the min() macro.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Cc: Chase Douglas <chase.douglas@canonical.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <20100929080823.GA13595@liondog.tnic>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
