5718 B0 and 5719 devices will use a new selfboot firmware format. This
patch adds code to detect the new format so that bootcode versions get
reported correctly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of fib_hash_lock rwlock.
The fn_zone hash table resize is the noticeable part of this patch.
I added a seqlock per fn_zone, so that readers can restart their lookup
in the (very rare) case a writer expanded the hash table.
Add rcu heads in fib_alias and fib_node, use call_rcu() to defer their
freeing, and use appropriate _rcu list manipulations.
Stress test (160.000.000 udp frames sent, IP route cache disabled to
mimic DDOS attack, FIB_HASH)
Before:
real 0m41.191s
user 0m13.137s
sys 8m55.241s
After:
real 0m38.091s
user 0m13.189s
sys 7m53.018s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step for RCU conversion of fib_hash :
struct fn_zone are created and never deleted.
Very classic conversion, using rcu_assign_pointer(), rcu_dereference()
and rtnl_dereference() verbs.
__rcu markers on fz_next and fn_zone_list
They are created under RTNL, we dont need fib_hash_lock anymore in
fn_new_zone().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking for false sharing problems, I noticed
sizeof(struct fn_zone) was small (28 bytes) and possibly sharing a cache
line with an often written kernel structure.
Most of the time, fn_zone uses its initial hash table of 16 slots.
We can avoid the false sharing problem by embedding this initial hash
table in fn_zone itself, so that sizeof(fn_zone) > L1_CACHE_BYTES
We did a similar optimization in commit a6501e080c (Reduce memory needs
and speedup lookups)
Add a fz_revorder field to speedup fn_hash() a bit.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the standard macro to put this table in __devinitconst.
Compiled, untested.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a network bench, I noticed an unfortunate false sharing between
'loopback_dev' and 'count' fields in "struct net".
'count' is written each time a socket is created or destroyed, while
loopback_dev might be often read in routing code.
Move loopback_dev in a read mostly section of "struct net"
Note: struct netns_xfrm is cache line aligned on SMP.
(It contains a "struct dst_ops")
Move it at the end to avoid holes, and reduce sizeof(struct net) by 128
bytes on ia32.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As CWR is stronger than CA_Disorder state, we can miscount
SACK/Reno failure into other timeouts. Not a bad problem as
it can happen only due to ECN, FRTO detecting spurious RTO
or xmit error which are the only callers of tcp_enter_cwr.
And even then losses and RTO must still follow thereafter
to actually end up into the relevant code paths.
Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
When only fast rexmit should be done, tcp_mark_head_lost marks
L too far. Also, sacked_upto below 1 is perfectly valid number,
the packets == 0 then needs to be trapped elsewhere.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppress a large block of warnings like:
drivers/net/niu.c:7094:38: warning: incorrect type in assignment (different base types)
drivers/net/niu.c:7094:38: expected restricted __be32 [usertype] ip4src
drivers/net/niu.c:7094:38: got unsigned long long
drivers/net/niu.c:7104:17: warning: cast from restricted __be32
...
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a commentary which elaborates that 'ubifs_recover_log_leb()' recovers only
the last log LEB, not any. Also remove some unneeded newlines.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Revert commit 54672386cc
"firewire: ohci: fix up configuration of TI chips".
It caused massive slow-down and data corruption with a TSB82AA2 based
StarTech EC1394B2 ExpressCard and FireWire 800 harddisks.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/657081http://thread.gmane.org/gmane.linux.kernel.firewire.user/4013
The fact that some card EEPROMs do not program these enhancements may be
related to TSB81BA3 phy chip errata, if not to bugs of TSB82AA2 itself.
We could re-add these configuration steps, but only conditional on a
whitelist of cards on which these enhancements bring a proven positive
effect.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org> 2.6.35
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
diva doesn't use workqueue and there is no reason to flush the system
workqueue from diva_os_remove_soft_isr(). Remove it.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Armin Schindler <armin@melware.de>
The HDA specification does not allow for a codec to mute itself just
because the volume is reduced, so _of course_ somebody had to go and do
it. This wouldn'\''t hurt too much when the volume is adjusted by hand,
but programs like PA that try to set the volume automatically could
inadvertently mute the output.
To work around this, change the TLV dB information for the Master volume
on all Sigmatel HDA codecs to indicate the the minimal volume setting
actually mutes.
Reported-by: Colin Guthrie <gmane@colin.guthr.ie>
Reported-by: "Alexander E. Patrakov" <patrakov@gmail.com>
Tested-by: Colin Guthrie <cguthrie@mandriva.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BugLink: http://launchpad.net/bugs/617647
The current SKU value disables playback, so ignore the SKU value.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Realtek have ways of specifying external amps and more via a
special nid or via the Codec's subsystem ID, this is called "SKU".
The computer manufacturer sometimes gets this wrong, so we need
to be able to override or ignore the SKU customization value.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a driver module is unloaded and the last still open file is a raw
MIDI device, the card and its devices will be actually freed in the
snd_card_file_remove() call when that file is closed. Afterwards, rmidi
and rmidi->card point into freed memory, so the module pointer is likely
to be garbage.
(This was introduced by commit 9a1b64caac.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Krzysztof Foltman <wdev@foltman.com>
Cc: 2.6.30-2.6.35 <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If we compile the ASoC code with PM disabled, we hit stuff like:
sound/soc/soc-dapm.c: In function 'snd_soc_dapm_suspend_check':
sound/soc/soc-dapm.c:440: warning: unused variable 'codec'
So tweak the stub macro to avoid these issues.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SoCs have a standard set of tuples consisting of frequency and
voltage pairs that the device will support per voltage domain. These
are called Operating Performance Points or OPPs. The actual
definitions of OPP varies over silicon versions. For a specific domain,
we can have a set of {frequency, voltage} pairs. As the kernel boots
and more information is available, a default set of these are activated
based on the precise nature of device. Further on operation, based on
conditions prevailing in the system (such as temperature), some OPP
availability may be temporarily controlled by the SoC frameworks.
To implement an OPP, some sort of power management support is necessary
hence this library depends on CONFIG_PM.
Contributions include:
Sanjeev Premi for the initial concept:
http://patchwork.kernel.org/patch/50998/
Kevin Hilman for converting original design to device-based.
Kevin Hilman and Paul Walmsey for cleaning up many of the function
abstractions, improvements and data structure handling.
Romit Dasgupta for using enums instead of opp pointers.
Thara Gopinath, Eduardo Valentin and Vishwanath BS for fixes and
cleanups.
Linus Walleij for recommending this layer be made generic for usage
in other architectures beyond OMAP and ARM.
Mark Brown, Andrew Morton, Rafael J. Wysocki, Paul E. McKenney for
valuable improvements.
Discussions and comments from:
http://marc.info/?l=linux-omap&m=126033945313269&w=2http://marc.info/?l=linux-omap&m=125482970102327&w=2http://marc.info/?t=125809247500002&r=1&w=2http://marc.info/?l=linux-omap&m=126025973426007&w=2http://marc.info/?t=128152609200064&r=1&w=2http://marc.info/?t=128468723000002&r=1&w=2
incorporated.
v1: http://marc.info/?t=128468723000002&r=1&w=2
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If the device which fails to resume is part of a loadable kernel module
it won't be checked at startup against the magic number stored in the
RTC.
Add a read-only sysfs attribute /sys/power/pm_trace_dev_match which
contains a list of newline separated devices (usually just the one)
which currently match the last magic number. This allows the device
which is failing to resume to be found after the modules are loaded
again.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Lock the PM device list mutex using device_pm_lock() and
device_pm_unlock() around the list iteration in show_dev_hash().
show_dev_hash() was reverse iterating dpm_list without first locking the
mutex that the functions in drivers/base/power/main.c lock. I assume
this was unintentional since there is no comment suggesting why the lock
might not be necessary.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If runtime suspend of a device fails returning -EAGAIN or -EBUSY,
which means that it's safe to try to suspend it again, the PM core
runs the runtime idle helper function for it. Unfortunately this may
lead to problems, for example for PCI devices whose drivers don't
implement the ->runtime_idle() callback, because in that case the
PCI bus type's ->runtime_idle() always calls pm_runtime_suspend()
for the given device. Then, if there's an automatic idle
notification after the driver's ->runtime_suspend() returning -EAGAIN
or -EBUSY, it will make the suspend happen again possibly causing a
busy loop to appear. To avoid that, remove the idle notification
after failing runtime suspend of a device altogether and let the
callers of pm_runtime_suspend() repeat the operation if need be.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Since we are adding compression to the kernel's hibernate code,
change signature used by it to mark swap spaces, so that earlier
kernels don't attempt to restore compressed images they cannot
handle.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reduce code duplication in rpm_idle(), rpm_suspend() and rpm_resume()
by using local pointers to store callback addresses and moving some
duplicated code into a separate function.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
If there is a wakeup event during the freezing of tasks, suspend or
hibernation will fail anyway. Since try_to_freeze_tasks() can take
up to 20 seconds to complete or fail, aborting it as soon as a wakeup
event is detected improves the worst case wakeup latency.
Based on a patch from Arve Hjønnevåg.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
The patch "PM / Runtime: Implement autosuspend support" introduces
"autosuspend" facility for runtime PM, but misses helper function
of pm_request_autosuspend, so add it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The hibernate resume code checks if there is an image to resume from
on every boot and, if the kernel is built with CONFIG_PM_DEBUG set
and the image is not present, it prints some scary messages
suggesting there was a boot error of some sort. Apparently, some
users are confused by them, so make them look less scary and adjust
the other hibernate resume debug messages to match them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1427) implements the "autosuspend" facility for runtime
PM. A few new fields are added to the dev_pm_info structure and
several new PM helper functions are defined, for telling the PM core
whether or not a device uses autosuspend, for setting the autosuspend
delay, and for marking periods of device activity.
Drivers that do not want to use autosuspend can continue using the
same helper functions as before; their behavior will not change. In
addition, drivers supporting autosuspend can also call the old helper
functions to get the old behavior.
The details are all explained in Documentation/power/runtime_pm.txt
and Documentation/ABI/testing/sysfs-devices-power.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Some devices, such as USB interfaces, cannot be power-managed
independently of their parents, i.e., they cannot be put in low power
while the parent remains at full power. This patch (as1425) creates a
new "no_callbacks" flag, which tells the PM core not to invoke the
runtime-PM callback routines for the such devices but instead to
assume that the callbacks always succeed. In addition, the
non-debugging runtime-PM sysfs attributes for the devices are removed,
since they are pretty much meaningless.
The advantage of this scheme comes not so much from avoiding the
callbacks themselves, but rather from the fact that without the need
for a process context in which to run the callbacks, more work can be
done in interrupt context.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1424) combines the various public entry points for the
runtime PM routines into three simple functions: one for idle, one for
suspend, and one for resume. A new bitflag specifies whether or not
to increment or decrement the usage_count field.
The new entry points are named __pm_runtime_idle,
__pm_runtime_suspend, and __pm_runtime_resume, to reflect that they
are trampolines. Simultaneously, the corresponding internal routines
are renamed to rpm_idle, rpm_suspend, and rpm_resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1423) merges the asynchronous routines
__pm_request_idle(), __pm_request_suspend(), and __pm_request_resume()
with their synchronous counterparts. The RPM_ASYNC bitflag argument
serves to indicate what sort of operation to perform.
In the course of performing this merger, it became apparent that the
various functions don't all behave consistenly with regard to error
reporting and cancellation of outstanding requests. A new routine,
rpm_check_suspend_allowed(), was written to centralize much of the
testing, and the other functions were revised to follow a simple
algorithm:
If the operation is disallowed because of the device's
settings or current state, return an error.
Cancel pending or scheduled requests of lower priority.
Schedule, queue, or perform the desired operation.
A few special cases and exceptions are noted in comments.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The "from_wq" argument in __pm_runtime_suspend() and
__pm_runtime_resume() supposedly indicates whether or not the function
was called by the PM workqueue thread, but in fact it isn't always
used this way. It really indicates whether or not the function should
return early if the requested operation is already in progress.
Along with this badly-named boolean argument, later patches in this
series will add several other boolean arguments to these functions and
others. Therefore this patch (as1422) begins the conversion process
by replacing from_wq with a bitflag argument. The same bitflags are
also used in __pm_runtime_get() and __pm_runtime_put(), where they
indicate whether or not the operation should be asynchronous.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1421) moves the PM runtime accounting subroutines up to
the beginning of runtime.c, taking them out of the middle of the
functions that do the actual work. No operational changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1420) adds sysfs_merge_group() and sysfs_unmerge_group()
functions, allowing drivers easily to add and remove sets of
attributes to a pre-existing attribute group directory.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There is a potential issue with the asynchronous suspend code that
a device driver suspending asynchronously may not notice that it
should back off. There are two failing scenarions, (1) when the
driver is waiting for a driver suspending synchronously to complete
and that second driver returns error code, in which case async_error
won't be set and the waiting driver will continue suspending and (2)
after the driver has called device_pm_wait_for_dev() and the waited
for driver returns error code, in which case the caller of
device_pm_wait_for_dev() will not know that there was an error and
will continue suspending.
To fix this issue make __device_suspend() set async_error, so
async_suspend() doesn't need to set it any more, and make
device_pm_wait_for_dev() return async_error, so that its callers
can check whether or not they should continue suspending.
No more changes are necessary, since device_pm_wait_for_dev() is
not used by any drivers' suspend routines.
Reported-by: Colin Cross <ccross@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce struct wakeup_source for representing system wakeup sources
within the kernel and for collecting statistics related to them.
Make the recently introduced helper functions pm_wakeup_event(),
pm_stay_awake() and pm_relax() use struct wakeup_source objects
internally, so that wakeup statistics associated with wakeup devices
can be collected and reported in a consistent way (the definition of
pm_relax() is changed, which is harmless, because this function is
not called directly by anyone yet). Introduce new wakeup-related
sysfs device attributes in /sys/devices/.../power for reporting the
device wakeup statistics.
Change the global wakeup events counters event_count and
events_in_progress into atomic variables, so that it is not necessary
to acquire a global spinlock in pm_wakeup_event(), pm_stay_awake()
and pm_relax(), which should allow us to avoid lock contention in
these functions on SMP systems with many wakeup devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Seen on MIPS32, gcc 4.4.3, 2.6.36-rc4:
drivers/base/power/main.c: In function 'dpm_show_time':
drivers/base/power/main.c:415: warning: comparison of distinct pointer types lacks a cast
do_div() takes unsigned parameters:
uint32_t do_div(uint64_t *n, uint32_t base);
Using an unsigned variable for usecs64 should not cause any problems,
because calltime >= starttime .
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The default hibernation image size is currently hard coded and euqal
to 500 MB, which is not a reasonable default on many contemporary
systems. Make it equal 2/5 of the total RAM size (this is slightly
below the maximum, i.e. 1/2 of the total RAM size, and seems to be
generally suitable).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: M. Vefa Bicakci <bicave@superonline.com>
One comment in hibernate_preallocate_memory() is wrong, so fix it and
add one more comment to clarify the meaning of the fixed one.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Although we need the PM workqueue to be freezable, we don't need it
to be singlethread. Also, the number of concurrent work items
running on a single CPU need not be constrained. For these reasons
use alloc_workqueue() directly, with suitable arguments, instead of
create_freezeable_workqueue(), to create the runtime PM workqueue.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Tejun Heo <tj@kernel.org>
Fix the following build warning:
warning: (PM_SLEEP_SMP && SMP && (ARCH_SUSPEND_POSSIBLE || \
ARCH_HIBERNATION_POSSIBLE) && PM_SLEEP) selects HOTPLUG_CPU which \
has unmet direct dependencies (SMP && HOTPLUG)
by selecting HOTPLUG along with CPU_HOTPLUG.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Compress hibernation image with LZO in order to save on I/O and
therefore time to hibernate/thaw.
[rjw: Added hibernate=nocompress command line option instead of just
nocompress which would be confusing, fixed a couple of compiler
warnings, fixed kerneldoc comments, minor cleanups.]
Signed-off-by: Bojan Smojver <bojan@rexursive.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Allow drivers, that belong to subsystems which use the generic
runtime pm callbacks, not to define runtime pm suspend/resume handlers,
by implicitly assuming success in such cases.
This is needed to eliminate nop handlers that would otherwise be
necessary by drivers which enable runtime pm, but don't need
to do anything when their devices are runtime-suspended/resumed.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The core code now initializes the requested number of interrupts and
sets the flags in irq_desc.status which are requested by the
architecture via ARCH_IRQ_INIT_FLAGS.
Add ARCH_IRQ_INIT_FLAGS and remove the loop which sets those flags
after the irq descriptors are allocated.
[ This patch should have been in the original irq rework and got
dropped accidentaly ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
The parisc version of the perf code is sufficiently
protected by its own spinlock, no need to use the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: linux-parisc@vger.kernel.org
