Enable dynamic debugging and remove a bunch of #ifdef/#endifs.
Add a lapb_dbg(level, fmt, ...) macro and replace the
printk(KERN_DEBUG uses.
Add pr_fmt and remove embedded prefixes.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Killing reset task while adapter is resetting causes deadlock.
Only kill reset task if adapter is not resetting.
Ref bug #43132 on bugzilla.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since recent changes on TCP splicing (starting with commits 2f533844
"tcp: allow splice() to build full TSO packets" and 35f9c09f "tcp:
tcp_sendpages() should call tcp_push() once"), I started seeing
massive stalls when forwarding traffic between two sockets using
splice() when pipe buffers were larger than socket buffers.
Latest changes (net: netdev_alloc_skb() use build_skb()) made the
problem even more apparent.
The reason seems to be that if do_tcp_sendpages() fails on out of memory
condition without being able to send at least one byte, tcp_push() is not
called and the buffers cannot be flushed.
After applying the attached patch, I cannot reproduce the stalls at all
and the data rate it perfectly stable and steady under any condition
which previously caused the problem to be permanent.
The issue seems to have been there since before the kernel migrated to
git, which makes me think that the stalls I occasionally experienced
with tux during stress-tests years ago were probably related to the
same issue.
This issue was first encountered on 3.0.31 and 3.2.17, so please backport
to -stable.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: <stable@vger.kernel.org>
Use DT_MACHINE_START() on the emev2 based KZM9D board.
Also include a tiny DTS file to describe the board and
update the Kconfig dependencies to select CONFIG_USE_OF.
Update the SMP glue code to use OF for matching.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is EMEV2 DT support V3. The support is limited to
whatever devices that are complied in the kernel. At this
point we have UARTs handled by "em-uart" and a timer
handled by "em-sti". Clocks and SMP are not supported.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tie in the on-board Ethernet controller on KZM9D
and make use of the GPIO controller for external
IRQ pin support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tie in the Emma Mobile GPIO driver "em-gio" to
support the GPIOs on Emma Mobile EV2.
A static IRQ range is used to allow boards to
hook up their platform devices to the GPIOs.
DT support is still on the TODO for the GPIO driver,
so only platform device support is included here.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is V3 of Emma Mobile EV2 SMP support.
At this point only the most basic form of SMP operation
is supported. TWD and CPU Hotplug support is excluded.
Tied to both the Emma Mobile EV2 and the KZM9D board
due to the need to switch on board in platsmp.c and
the newly introduced need for static mappings.
The static mappings are needed to allow hardware
acces early during boot when SMP is initialized.
This early requirement forces us to also map in
the SMU registers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
V3 of basic KZM9D board support. At this point a quite
thin layer that makes use of the Emma Mobile EV2 SoC code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is V3 of the Emma Mobile EV2 SoC support.
Included here is support for serial and timer
devices which is just about enough to boot a kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This driver has been converted to use regulator_map_voltage_linear and
set_voltage_sel now. regulator_map_voltage_linear will check the the voltage
falls within specified range. The check_range() function and max_uV field are
not used now, remove them.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver has been converted to use regulator_map_voltage_linear and
set_voltage_sel now. regulator_map_voltage_linear will check the the voltage
falls within specified range. The check_range() function is not used, remove it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver has been converted to set_voltage_sel and regulator_map_voltage_linear.
regulator_map_voltage_linear will check the voltage falls within specified range.
The max_uV field is not used now, remove it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is V2 of the Emma Mobile GPIO driver. This
driver is designed to be reusable between multiple SoCs
that share the same basic building block, but so far it
has only been used on Emma Mobile EV2.
Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on two I/O memory
ranges and the 32 GPIOs are hooked up to two interrupts.
In the case of Emma Mobile EV2 this GPIO building block
is used as main external interrupt controller hooking up
159 GPIOS as 159 interrupts via 5 driver instances and
10 interrupts to the GIC and the Cortex-A9 Dual.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
While the RNC is suspended for I/O cleanup, the remote device can be
stopped and the RNC setup for destruction. These changes accomodate that
case in the abort path.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This fix corrects the saving of resume parameters when the destruction
of the RNC has already been directed, and makes sure not to overwrite
the RNC destruction callbacks.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The RNC state machine would incorrectly transition from
SCI_RNC_AWAIT_SUSPENSION directly to SCI_RNC_INVALIDATING when a destruct
request was made. This would skip the increment of the suspension count
and the abort of pending TCs (although the invalidating state would at
least cleanup outstanding TCs).
Instead, the RNC will transition to SCI_RNC_SUSPENDED and then start the
destruction process.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Since there is a possibilty of a timeout waiting for the RNC suspension,
handle the exit case from the task termination under scic_lock, and leave
the tag allocated if the termination timed-out.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Since the callbacks to libsas now occur under scic_lock, there is no
longer any reason to save the completed requests in a separate list
for completion to libsas.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the link fail path, set IDEV_GONE for every device on the domain
when the last link in the port fails.
In the abort path functions like isci_reset_device, make sure that
there has not already been a detected domain failure with the device
by checking IDEV_GONE, before performing any kind of hard reset, SMP
phy control, or TMF operation.
The check for IDEV_GONE makes sure that the device in the abort path
really has control of the port with which it is associated. This
prevents starting hard resets at incorrect times and scheduling
unnecessary LUN resets for SATA devices.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The ATAPI specific and STP general RNC suspension code had been
incorrectly removed from the remote device code.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Make sure that the wait for suspend can handle the RNC destruction case.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is an apparent HW lockup caused when the PE is disabled while there
is an outstanding TC in progress. This change puts the link into OOB to
force the TC to end before the PE is disabled.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This change adds timeouts to the RNC suspension wait. It makes the
suspend and resume timeouts the same.
The previous resume timeout of 5 ms was too short, and timeouts were
seen in resumptions of devices in the abort task/LUN reset path - which
would receive an RNC resumed message within a tenth of a second later.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Requests contructed as task management requests need to have the protocol
indicator set so the completion decode can observe any RNC suspension
conditions.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
TMF requests, unlike normal I/O requests, need to handle I/O management
conditions in the completion function because TMFs are not handled in the
completion tasklet.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the case of TMF execution, or device resets, wait for the RNC to fully
resume before returning to the caller. This ensures that the remote
device will not fail I/O requests while waiting for the RNC resumption to
complete.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Instead of immediately transitioning to the SCI_RNC_AWAIT_SUSPENSION
state, handle the SCI_RNC_RESUMING suspend transition from the
SCI_RNC_READY state like the SCI_RNC_INVALIDATING --> SCI_RNC_POSTING
transitions do now, by setting the destination state for the entry
into the READY state.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When an individual request is being terminated, the request's tag
is managed in the terminate function.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch changes the callback mechanism to libsas to only occur while
the scic_lock is held; the abort path cleanup of I/Os also checks to make
sure IREQ_ABORT_PATH_ACTIVE is clear before proceding.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Completion of I/Os during the one of the abort path interface calls
from libsas can drive remote device state changes and the resumption
of the device RNC. This is a problem when the abort path is
attempting to cleanup outstanding I/O at the same time - the resumption
can prevent the termination from occuring correctly.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In order to prevent a device from receiving an I/O request while still
in an RNC suspending or resuming state (and therefore failing that
I/O back to libsas with a reset required status) wait for the RNC state
change before proceding in the abort path.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the libsas error path, SATA disks require extra handling in
libata to recover operation. However, libsas expects to be able
to immediately recover all outstanding I/O once the error handler
escalation stops. This patch fixes the condition where the libata
error handler is scheduled for operation but libsas has already
deleted the outstanding sas_tasks.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The LLHANG timer should be enabled once per device. This patch corrects
both the timer enable and the timer disable for the remote device.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In the case of a suspend call while in SCI_RNC_POSTING or INVALIDATING
states, the LLHANG detect needed to be saved so the upcoming suspension
would enable it correctly. The unused suspend callback parameters were
removed.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This addresses a regression from the commit "isci: Redesign
device suspension, abort, cleanup." in which the sas_task end
condition for terminated I/Os was made to call back on
sas_task_abort()".
This commit will be rolled into the original.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For NCQ error conditions among others, there is no need to enable
the link layer hang detect timer.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The RNC can be any of the states in the loop from suspended to
ready when the API "suspend" or "resume" are called. This change
adds destination states parameters that control the suspension /
resumption action of the RNC statemachine for those transition states.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This commit changes the means by which outstanding I/Os are handled
for cleanup.
The likelihood is that this commit will be broken into smaller pieces,
however that will be a later revision. Among the changes:
- All completion structures have been removed from the tmf and
abort paths.
- Now using one completed I/O list, with the I/O completed in host bit being
used to select error or normal callback paths.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If LUN reset sees that the device is gone, it returns TMF_RESP_FUNC_FAILED
to cause libsas to escalate to an I_T_Nexus_Reset.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fixing the remote device state machine to suspend and terminate
all outstanding I/O before the device stopped state is reached.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When the remote device enters the NCQ error state, the device must
be suspended so that the I/O terminations can take place.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
TCs must be terminated only while the RNC is suspended. This commit
adds remote device suspensions and resumptions in the abort, reset and
termination paths.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
TCs must only be terminated when RNCs are suspended.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add comprehensive decode for all TC completions that generate RNC
suspensions.
Note that this commit also removes unconditional resumptions of ATAPI
devices when in the SCI_STP_DEV_ATAPI_ERROR state, and STP devices
when in the SCI_STP_DEV_IDLE state. This is because the SCI_STP_DEV_IDLE
and SCI_STP_DEV_ATAPI state entry functions manage the RNC resumption.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
