I forgot to remove the ide_etrax100 chipset type when removing the
ETRAX_IDE driver.
Reported-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reported-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
If you delay 30s or more before mounting a CD after inserting it then
the kernel has the wrong value for the CD size.
http://marc.info/?t=121276133000001
The problem is in sr_test_unit_ready(): the function eats unit
attentions without adjusting the sdev->changed status. This means
that when the CD signals changed media via unit attention, we can
ignore it. Fix by making sr_test_unit_ready() adjust the changed
status.
Tested-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Found a silly double assignment of err is do_shmat. Silly, but good to
clean up the useless code.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MDIO-less PHYs should use CONFIG_FIXED_PHY driver and appropriate
fixed-link property in the device tree.
If not, ethernet will not work:
e0024520:03 not found
eth1: Could not attach to PHY
IP-Config: Failed to open eth1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
more unification. Should cause no change in functionality.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
cpuid(0x05) provides extended information about MWAIT in EDX when bit
0 of ECX is set. Bit 4-7 of EDX determine whether MWAIT is supported
for C1. C1E enabled CPUs have these bits set to 0.
Based on an earlier patch from Andi Kleen.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simplify code: no need to do a cpuid(1) again. The cpuinfo structure
has all necessary information already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename the "MSR_K8_ENABLE_C1E" MSR to INT_PENDING_MSG, which is the
name in the data sheet as well. Move the C1E mask to the header file.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
default_idle is selected in cpu_idle(), when no other idle routine is
selected. Select it in select_idle_routine() when mwait is not
selected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When a 64-bit x86 processor runs in 32-bit PAE mode, a pte can
potentially have the same number of physical address bits as the
64-bit host ("Enhanced Legacy PAE Paging"). This means, in theory,
we could have up to 52 bits of physical address in a pte.
The 32-bit kernel uses a 32-bit unsigned long to represent a pfn.
This means that it can only represent physical addresses up to 32+12=44
bits wide. Rather than widening pfns everywhere, just set 2^44 as the
Linux x86_32-PAE architectural limit for physical address size.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently arch/x86/kernel/pci-dma.c always adds __GFP_NORETRY
to the allocation flags, because it wants to be reasonably
sure not to deadlock when calling alloc_pages().
But really that should only be done in two cases:
- when allocating memory in the lower 16 MB DMA zone.
If there's no free memory there, waiting or OOM killing is of no use
- when optimistically trying an allocation in the DMA32 zone
when dma_mask < DMA_32BIT_MASK hoping that the allocation
happens to fall within the limits of the dma_mask
Also blindly adding __GFP_NORETRY to the the gfp variable might
not be a good idea since we then also use it when calling
dma_ops->alloc_coherent(). Clearing it might also not be a
good idea, dma_alloc_coherent()'s caller might have set it
on purpose. The gfp variable should not be clobbered.
[ mingo@elte.hu: converted to delta patch ontop of previous version. ]
Signed-off-by: Miquel van Smoorenburg <miquels@cistron.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
schedule() has the special "TASK_INTERRUPTIBLE && signal_pending()" case,
this allows us to do
current->state = TASK_INTERRUPTIBLE;
schedule();
without fear to sleep with pending signal.
However, the code like
current->state = TASK_KILLABLE;
schedule();
is not right, schedule() doesn't take TASK_WAKEKILL into account. This means
that mutex_lock_killable(), wait_for_completion_killable(), down_killable(),
schedule_timeout_killable() can miss SIGKILL (and btw the second SIGKILL has
no effect).
Introduce the new helper, signal_pending_state(), and change schedule() to
use it. Hopefully it will have more users, that is why the task's state is
passed separately.
Note this "__TASK_STOPPED | __TASK_TRACED" check in signal_pending_state().
This is needed to preserve the current behaviour (ptrace_notify). I hope
this check will be removed soon, but this (afaics good) change needs the
separate discussion.
The fast path is "(state & (INTERRUPTIBLE | WAKEKILL)) + signal_pending(p)",
basically the same that schedule() does now. However, this patch of course
bloats schedule().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
need to call early_reserve_e820() to preallocate mptable for 32bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
... so it could fall back to normal numa and we'd reduce the impact of the
NUMAQ subarch.
NUMAQ depends on GENERICARCH
also decouple genericarch numa from acpi.
also make it fall back to bigsmp if apicid > 8.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
a multi-socket test-system with 3 or 4 ioapics, when 4 dualcore cpus or
2 quadcore cpus installed, needs to switch to bigsmp or physflat.
CPU apic id is [4,11] instead of [0,7], and we need to check max apic
id instead of cpu numbers.
also add check for 32 bit when acpi is not compiled in or acpi=off.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
don't assume we can use RAM near the end of every node.
Esp systems that have few memory and they could have
kva address and kva RAM all below max_low_pfn.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now we are using register_e820_active_regions() instead of
add_active_range() directly. So end_pfn could be different between the
value in early_node_map to node_end_pfn.
So we need to make shrink_active_range() smarter.
shrink_active_range() is a generic MM function in mm/page_alloc.c but
it is only used on 32-bit x86. Should we move it back to some file in
arch/x86?
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
@r exists@
expression E,E1;
statement S;
position p1,p2,p3;
@@
E =@p1 \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != E = E1
if (E == NULL || ...) S
... when != E = E1
if@p2 (...) {
... when != kfree(E)
}
... when != E = E1
kfree@p3(E);
@forall@
position r.p2;
expression r.E;
int E1 != 0;
@@
* if@p2 (...) {
... when != kfree(E)
when strict
return E1; }
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
__ctl_load/__ctl_store are called with either an array of unsigned long or
a single unsigned long value. Add an address operator to the "m"/"=m"
contraints to make them work for unsigned long arguments as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The first argument to __ctl_store() should be the array to store
stuff in, not just the first element of that array. With the
current code in __cpu_up(), mainline GCC dies with an internal
compiler error. I didn't diagnose that further, but just fixed
the kernel bug.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Priorities for I/O interruption subclasses range from 0 (highest)
to 7 (lowest). Unfortunately, the console has been using isc 7
instead of an isc with a higher priority than regular I/O
subchannels (which use 3). Fix this by making the console use
isc 1.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a memory range is supposed to be added to the 1:1 mapping and it
ends just below the maximum supported physical address it won't
succeed. This is because a test doesn't consider that the end address
is 1 smaller than start + size.
Fix the comparison.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sparse complains about signedness:
drivers/s390/cio/blacklist.c:132:28: warning: incorrect type in
argument 2 (different signedness)
drivers/s390/cio/blacklist.c:132:28: expected unsigned int *val
drivers/s390/cio/blacklist.c:132:28: got int *cssid
drivers/s390/cio/blacklist.c:136:28: warning: incorrect type in
argument 2 (different signedness)
drivers/s390/cio/blacklist.c:136:28: expected unsigned int *val
drivers/s390/cio/blacklist.c:136:28: got int *ssid
drivers/s390/cio/blacklist.c:140:28: warning: incorrect type in
argument 2 (different signedness)
drivers/s390/cio/blacklist.c:140:28: expected unsigned int *val
drivers/s390/cio/blacklist.c:140:28: got int *devno
cssid, ssid and devno are of course unsigned, so let's make the
variables unsigned as well.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of !64BIT kernel we end up with a zero sized mem_section array.
This happens because NR_MEM_SECTIONS is smaller than SECTIONS_PER_ROOT
but we have:
#define NR_SECTION_ROOTS (NR_MEM_SECTIONS / SECTIONS_PER_ROOT)
and
struct mem_section *mem_section[NR_SECTION_ROOTS];
So fix this by selecting SPARSEMEM_STATIC which makes sure
that SECTIONS_PER_ROOT is 1.
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Remove IB_DEVICE_SEND_W_INV capability flag
IB/umem: Avoid sign problems when demoting npages to integer
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin serial driver: fix up tty core set_ldisc API change breakage bug
Blackfin arch: protect only the SPI bus controller with CONFIG_SPI_BFIN
Blackfin arch: fixup warnings with the new cplb saved values
Blackfin Serial Driver: Clean up BF54x macro in blackfin UART driver.
The bindv6only is tuned via sysctl. It is already on a struct net
and per-net sysctls allow for its modification (ipv6_sysctl_net_init).
Despite this the value configured in the init net is used for the
rest of them.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-tip testing found the following build error:
drivers/built-in.o: In function `mcs_receive_irq':
mcs7780.c:(.text+0x4e429): undefined reference to `crc32_le'
drivers/built-in.o: In function `mcs_hard_xmit':
mcs7780.c:(.text+0x4e9af): undefined reference to `crc32_le'
with:
http://redhat.com/~mingo/misc/config-Sun_Jun__8_22_56_14_CEST_2008.bad
the reason is a missing enablement of the CRC32 library in the Kconfig.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increments the version to 3.92.1.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 5761 non-e devices, two problems prevent the administrator from
overriding the WOL settings in the device's NVRAM.
The first problem is that GPIO 0 and GPIO 2 have been swapped. This
change prevented the administrator from turning on WOL when it is
disabled in NVRAM. The fix is to add a new path for the 5761 that
swaps the two GPIOs in the code as well.
The second problem is that GPIO 1 could not be toggled by the driver
because the GPIO is shared with the debug UART GPIO. This will prevent
the administrator from being able to turn WOL off if it was enabled in
NVRAM. The fix is to always disable the debug UART after a GRC reset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where the TG3_FLAG_10_100_ONLY flag was
testing against the wrong flags variable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The git commit ef167e2703 entitled
"Fix supporting flowctrl code" introduced a bug that prevents 5714S,
5715S and 5780S devices from falling back to a forced link mode. The
problem is that the added flow control check will always fail if flow
control is set to autoneg and either RX or TX (or both) flow control
is enabled. The driver defaults to setting flow control to autoneg
and advertises both RX and TX flow control.
The fix is to remove the errant check.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 54d29ad33e (Power Supply: fix race
in device_create) introduced a race in power_supply_uevent. Previously it
checked that power_supply is available by checking for dev->driver_data.
But now dev->driver_data is set before power_supply->dev is initialised.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
fix race between:
ieee80211_open->ieee80211_led_radio->led_trigger_event->led_set_brightness->iwl3945_led_brightness_set
(which assumes that "led->priv" is not NULL)
and
iwl3945_pci_probe->iwl3945_setup_deferred_work->(...)->iwl3945_bg_alive_start->iwl3945_alive_start->iwl3945_led_register->iwl3945_led_register_led
which sets priv field in struct iwl3945_led
after
led->led_dev.brightness_set = iwl3945_led_brightness_set;
(...)
led_classdev_register(device, &led->led_dev);
http://kerneloops.org/guilty.php?guilty=iwl3945_led_brightness_set&version=2.6.25-release&start=1671168&end=1703935&class=oops
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: ipw3945-devel@lists.sourceforge.net
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a typo in the name of a config variable.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reviewed-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a check to the set_channel flow. When attempting to change
the channel while in IBSS mode, and the new channel does not support IBSS
mode, the flow return with an error value with no consequences on the
mac80211 and driver state.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sufficient scans (at least 2 or 3) should have been done within 7
seconds to find an existing IBSS to join. This should improve IBSS
creation latency; and since IBSS merging is still in effect, shouldn't
have detrimental effects on eventual IBSS convergence.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a data alignment issue in the zd1211rw driver.
The IEEE80211_STYPE_QOS_DATA bit should be used as a bitwise test
to test for the presence of the 2 byte QoS control field.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
