These signatures are well known bit patterns, mostly made up
of ascii characters. Mentally parsing works best if they
are printed in hex.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take advantage of standard device name prefixing and
netdevice msglvl control where possible.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix cut'n'paste typo. Log the bogus length and not the
irrelevant signature.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet use the hard_mtu value for sizing the tx queue and nothing
else. We will be transmitting buffers of up to tx_max size, so
that's the proper value to give usbnet.
The individual datagram size is completely irrelevant here.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to keep this code duplicated from usbnet.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions were merely wrappers around the usbnet
variants. Remove them.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Padding NTBs to max size is part of the support for devices
optimizing their DMA transfers. This optimization depends on
max sized NTBs not being ZLP terminated. So we are much better
off dropping the padding if we are going to send a ZLP anyway.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The probed interface must be the master/control interface of the
function. Make this explicit and simplify redundant tests.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
header_desc was completely unused and union_desc was never used
outside cdc_ncm_bind_common.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to inform the device about the *new* value, not the
old one.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the call to cdc_ncm_setup() after the endpoint
setup removes the last remaining reference to ncm_parm
outside cdc_ncm_setup.
Collecting all the ncm_parm based calculations in
cdc_ncm_setup improves readability.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields are only used to prevent printing the same speeds
multiple times if we receive multiple identical speed notifications.
The value of these printk's is questionable, and even more so when
we filter out some of the notifications sent us by the firmware. If
we are going to print any of these, then we should print them all.
Removing little used fields is a bonus.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already use the usbnet udev field everywhere this could have
been used.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Too many pointers back and forth are likely to confuse developers,
creating subtle bugs whenever we forget to syncronize them all.
As a usbnet driver, we should stick with the standard struct
usbnet fields as much as possible. The netdevice is one such
field.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate stuff already in the common usbnet
struct. We still need to keep our special find_endpoints
function because we need explicit control over the selected
altsetting.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is always a duplicate of the "control" field. It causes
confusion wrt intf_data updates and cleanups.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can avoid the costly division for the common case where
we pad the frame to tx_max size as long as we ensure that
tx_max is either the device specified dwNtbOutMaxSize or not
a multiplum of wMaxPacketSize.
Using the preconverted 'maxpacket' field avoids converting
wMaxPacketSize to CPU endianness for every transmitted frame
And since we only will hit the one byte padding rule for short
frames, we can drop testing the skb for tailroom.
The change means that tx_max now represents the real maximum
skb size, enabling us to allocate the correct size instead of
always making room for one extra byte.
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of devices in the wild have turned out to require ZLPs.
Even if this is a spec violation, our priority is to make any
device work as good as possible. Devices needing ZLPs will fail
to receive any full sized frame we send. On the other hand,
devices which do not need the ZLP will still work if we send
them.
This gives us no other option than sending ZLPs by default.
This will prevent devices conforming to the spec from making the
optimizations which are possible without ZLPs. Adding known
such devices to a whitelist, to avoid the possible negative
impact of the new spec violating default.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
MBIM is a point-to-point protocol transporting raw IP packets
with no L2 headers. Only IPv4 and IPv6 are supported. ARP in
particular is not, which is quite logical given the lack of
L2 headers.
The driver still emulates an ethernet interface, dropping all
unsupported protocols, and avoiding neigbour resolving by
setting the IFF_NOARP flag.
The MBIM specification does not explicitly forbid IPv6 Neighbor
Discovery, and it seems the other OS support will respond to
Neighbor Solicitations on MBIM links. There are therefore
buggy devices out there, which despite the pointlessness, still
require Neighbor Discovery for IPv6 over MBIM.
This is incompatible with the IFF_NOARP flag which disables
both ARP and ND. We cannot support ARP in any case, so we
have to keep that flag. This patch implements a workaround
for the buggy devices, letting the driver respond directly
to Neighbor Solicitations from the device.
This is not optimal, but will have minimal effect on any sane
device.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Reported-and-tested-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fixes an incorrect function comment (probably copy/paste).
Signed-off-by: Ben Boeckel <mathstuf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to e1000, igb, ixgbe and ixgbevf.
Hong Zhiguo provides a fix for e1000 where tx_ring and adapter->tx_ring
are already of type "struct e1000_tx_ring" so no need to divide by
e1000_tx_ring size in the idx calculation.
Emil provides a fix for ixgbevf to remove a redundant workaround related
to header split and a fix for ixgbe to resolve an issue where the MTA table
can be cleared when the interface is reset while in promisc mode.
Todd provides a fix for igb to prevent ethtool from writing to the iNVM
in i210/i211 devices. This issue was reported by Marek Vasut <marex@denx.de>.
Anton Blanchard provides a fix for ixgbe to reduce memory consumption
with larger page sizes, seen on PPC.
Don provides a cleanup in ixgbe to replace the IXGBE_DESC_UNUSED macro with
the inline function ixgbevf_desc_unused() to make the logic a bit more
readable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves an issue where the MTA table can be cleared when the
interface is reset while in promisc mode. As result IPv6 traffic between
VFs will be interrupted.
This patch makes the update of the MTA table unconditional to avoid the
inconsistent clearing on reset.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch just replaces the IXGBE_DESC_UNUSED macro with a like named
inline function ixgbevf_desc_unused. The inline function makes the logic
a bit more readable.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver allocates pages for its receive rings. It currently
uses 512 pages, regardless of page size. During receive handling it
adds the unused part of the page back into the rx ring, avoiding the
need for a new allocation.
On a ppc64 box with 64 threads and 64kB pages, we end up with
512 entries * 64 rx queues * 64kB = 2GB memory used. Even more of a
concern is that we use up 2GB of IOMMU space in order to map all this
memory.
The driver makes a number of decisions based on if PAGE_SIZE is less
than 8kB, so use this as the breakpoint and only allocate 128 entries
on 8kB or larger page sizes.
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't let ethtool try to write to iNVM in i210/i211.
This fixes an issue seen by Marek Vasut.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes a workaround related to header split, which is redundant
because the driver does not support splitting packet headers on Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tx_ring and adapter->tx_ring are already of type "struct
e1000_tx_ring *"
Signed-off-by: Hong Zhiguo <zhiguohong@tencent.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using firmware assisted TSO, we use a single DMA mapping for
the linear area of a TSO skb.
We still have to segment the super-packet and insert a descriptor
containing the original headers before each segment of payload, so we
can unmap the linear area only after the last segment is completed.
The unmapping information for the linear area is therefore associated
with the last header descriptor.
We calculate the DMA address to unmap from using the map length and
the invariant that the end of the DMA mapping matches the end of
the data referenced by the last descriptor. But this invariant is
broken when there is TCP payload in the linear area.
Fix this by adding and using an explicit dma_offset field.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This patch removes the priv->can.do_get_state() callback, as it just returns
priv->can.state. The callback's only user can_fill_info() has direct access to
priv->can.state.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some devices, like the Kvaser Memorator Professional, have several bulk in
endpoints. Only the first one found must be used by the driver. The same holds
for the bulk out endpoint. The official Kvaser driver (leaf) was used as
reference for this patch.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If we handle end of block messages with higher priority than a lost message,
we can run into an endless interrupt loop.
This is reproducable with a am335x processor and "cansequence -r" at 1Mbit.
As soon as we loose a packet we can't escape from an interrupt loop.
This patch fixes the problem by handling lost packets before EOB packets.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The code sequence:
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(64);
pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
bypasses the architectures check on the DMA mask. It can be replaced
with dma_coerce_mask_and_coherent(), avoiding the direct initialization
of this mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code sequence:
pldat->pdev->dev.coherent_dma_mask = 0xFFFFFFFF;
pldat->pdev->dev.dma_mask = &pldat->pdev->dev.coherent_dma_mask;
bypasses the architectures check on the DMA mask. It can be replaced
with dma_coerce_mask_and_coherent(), avoiding the direct initialization
of this mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Copying whole packets with skb_copy_from_linear_data_offset is a pretty
bad idea. CPU was spending time in __copy_user_common and network
performance was lower. With the new solution iperf-measured speed
increased from 116Mb/s to 134Mb/s.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Putting the context id of the primary phy context in
the placeholder of the secondary is obviously a bad
idea.
Spotted by smatch.
Fixes: dac94da8db ("iwlwifi: mvm: new BT Coex API")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If beacon tx command failed the wmi command buffer
was not freed. This led to OOM in the long run.
This became aparent when stress testing
multi-BSSID.
Reported-By: Tomasz Skapski <tomasz.skapski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
sk_buff was not freed in some cases. The patch
unifies the msdu freeing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Don't update the slot in "bgmac_dma_rx_skb_for_slot" unless both the
skb alloc and dma mapping are successful; and free the newly allocated
skb if a dma mapping error occurs. This relieves the caller of the need
to deduce/execute the appropriate cleanup action required when an error
occurs.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calls to mal_enable_eob_irq perform a read-write-modify of a dcr to
enable device irqs which is protected by a spin lock. However calls to
mal_disable_eob_irq do not take the corresponding lock.
This patch resolves the problem by ensuring that calls to
mal_disable_eob_irq also take the lock.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug which would trigger the BUG_ON() at
net/core/dev.c:4156. It was found that this was due to continuing
processing in the current poll call even when the call to
napi_reschedule failed, indicating the device was already on the
polling list. This resulted in an extra call to napi_complete which
triggered the BUG_ON().
This patch ensures that we only contine processing rotting packets in
the current mal_poll call if we are not already on the polling list.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking if MAC address is valid using is_valid_ether_addr() is already done in
of_get_mac_address(). While at it, reorganize checking so it matches checks in
other drivers.
Signed-off-by: Luka Perkov <luka@openwrt.org>
CC: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
