In the packet timestamping function, check that the ptp version and
protocol of the packet matches what we have configured the hardware to
actually generate timestamps for, before looking/waiting for a timestamp.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the definition of PTP_CLASS_L2 to not have any bits overlapping with
the other defined protocol values, allowing the PTP_CLASS_* definitions to
be for simple filtering on packet type.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list of rx timestamps are currently only pruned of old entries when a
new entry is inserted. If no new entries are added, old timestamps may
survive beyond their lifetime, possible causing them to be attached to
packets with the same sequence number after a rollover.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rx_timestamp_work reschedules itself as a regular workqueue item,
effectively causing it run constantly as long as there are packets left in
the queue. Fix by using delayed workqueue items, limiting it to run only
every two jiffies.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only using the message type and sequence id for matching timestamps
with packets is error prone, as multiple clients may very well be
sending packets with the same messagetype and timestamp at the same
time. Fix by extending the check to include the hash of bytes 20-29
(source id in PTPv2) that is provided with the timestamps.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both tunnel6_protocol and tunnel46_protocol share the same error
handler, tunnel6_err(), which traverses through tunnel6_handlers list.
For ipip6 tunnels, we need to traverse tunnel46_handlers as we do e.g.
in tunnel46_rcv(). Current code can generate an ICMPv6 error message
with an IPv4 packet embedded in it.
Fixes: 73d605d1ab ("[IPSEC]: changing API of xfrm6_tunnel_register")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
By now, the recordmcount only records the function that in
following sections:
.text/.ref.text/.sched.text/.spinlock.text/.irqentry.text/
.kprobes.text/.text.unlikely
For the function that not in these sections, the call mcount
will be in place and not be replaced when kernel boot up. And
it will bring performance overhead, such as do_mem_abort (in
.exception.text section). This patch make the call mcount to
nop for this case in recordmcount.
Link: http://lkml.kernel.org/r/1446019445-14421-1-git-send-email-huawei.libin@huawei.com
Link: http://lkml.kernel.org/r/1446193864-24593-4-git-send-email-huawei.libin@huawei.com
Cc: <lkp@intel.com>
Cc: <catalin.marinas@arm.com>
Cc: <takahiro.akashi@linaro.org>
Cc: <stable@vger.kernel.org> # 3.18+
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In nop_mcount, shdr->sh_offset and welp->r_offset should handle
endianness properly, otherwise it will trigger Segmentation fault
if the recordmcount main and file.o have different endianness.
Link: http://lkml.kernel.org/r/563806C7.7070606@huawei.com
Cc: <stable@vger.kernel.org> # 3.0+
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When we are using the no-holes feature, if we punch a hole into a file
range that already contains a hole which overlaps the range we are passing
to fallocate(), we end up removing the extent map that represents the
existing hole without adding a new one. This happens because with the
no-holes feature we do not have explicit extent items to represent holes
and therefore the call to __btrfs_drop_extents(), made from
btrfs_punch_hole(), returns an end offset to the variable drop_end that
is smaller than the end of the range passed to fallocate(), while it
drops all existing extent maps in that range.
Normally having a missing extent map is not a problem, for example for
a readpages() operation we just end up building the extent map by
looking at the fs/subvol tree for a matching extent item (or a lack of
one for implicit holes). However for an fsync that uses the fast path,
which needs to look at the list of modified extent maps, this means
the fsync will not record information about the complete hole we had
before the fallocate() call into the log tree, resulting in a file with
content/layout that does not match what we had neither before nor after
the hole punch operation.
The following test case for fstests reproduces the issue. It fails without
this change because we get a file with a different digest after the fsync
log replay and also with a different extent/hole layout.
seq=`basename $0`
seqres=$RESULT_DIR/$seq
echo "QA output created by $seq"
tmp=/tmp/$$
status=1 # failure is the default!
trap "_cleanup; exit \$status" 0 1 2 3 15
_cleanup()
{
_cleanup_flakey
rm -f $tmp.*
}
# get standard environment, filters and checks
. ./common/rc
. ./common/filter
. ./common/punch
. ./common/dmflakey
# real QA test starts here
_need_to_be_root
_supported_fs generic
_supported_os Linux
_require_scratch
_require_xfs_io_command "fpunch"
_require_xfs_io_command "fiemap"
_require_dm_target flakey
_require_metadata_journaling $SCRATCH_DEV
# This test was motivated by an issue found in btrfs when the btrfs
# no-holes feature is enabled (introduced in kernel 3.14). So enable
# the feature if the fs being tested is btrfs.
if [ $FSTYP == "btrfs" ]; then
_require_btrfs_fs_feature "no_holes"
_require_btrfs_mkfs_feature "no-holes"
MKFS_OPTIONS="$MKFS_OPTIONS -O no-holes"
fi
rm -f $seqres.full
_scratch_mkfs >>$seqres.full 2>&1
_init_flakey
_mount_flakey
# Create out test file with some data and then fsync it.
# We do the fsync only to make sure the last fsync we do in this test
# triggers the fast code path of btrfs' fsync implementation, a
# condition necessary to trigger the bug btrfs had.
$XFS_IO_PROG -f -c "pwrite -S 0xaa 0K 128K" \
-c "fsync" \
$SCRATCH_MNT/foobar | _filter_xfs_io
# Now punch a hole against the range [96K, 128K[.
$XFS_IO_PROG -c "fpunch 96K 32K" $SCRATCH_MNT/foobar
# Punch another hole against a range that overlaps the previous range
# and ends beyond eof.
$XFS_IO_PROG -c "fpunch 64K 128K" $SCRATCH_MNT/foobar
# Punch another hole against a range that overlaps the first range
# ([96K, 128K[) and ends at eof.
$XFS_IO_PROG -c "fpunch 32K 96K" $SCRATCH_MNT/foobar
# Fsync our file. We want to verify that, after a power failure and
# mounting the filesystem again, the file content reflects all the hole
# punch operations.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foobar
echo "File digest before power failure:"
md5sum $SCRATCH_MNT/foobar | _filter_scratch
echo "Fiemap before power failure:"
$XFS_IO_PROG -c "fiemap -v" $SCRATCH_MNT/foobar | _filter_fiemap
# Silently drop all writes and umount to simulate a crash/power failure.
_load_flakey_table $FLAKEY_DROP_WRITES
_unmount_flakey
# Allow writes again, mount to trigger log replay and validate file
# contents.
_load_flakey_table $FLAKEY_ALLOW_WRITES
_mount_flakey
echo "File digest after log replay:"
# Must match the same digest we got before the power failure.
md5sum $SCRATCH_MNT/foobar | _filter_scratch
echo "Fiemap after log replay:"
# Must match the same extent listing we got before the power failure.
$XFS_IO_PROG -c "fiemap -v" $SCRATCH_MNT/foobar | _filter_fiemap
_unmount_flakey
status=0
exit
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
When executing generic/001 in a loop on a ppc64 machine (with both sectorsize
and nodesize set to 64k), the following call trace is observed,
WARNING: at /root/repos/linux/fs/btrfs/locking.c:253
Modules linked in:
CPU: 2 PID: 8353 Comm: umount Not tainted 4.3.0-rc5-13676-ga5e681d #54
task: c0000000f2b1f560 ti: c0000000f6008000 task.ti: c0000000f6008000
NIP: c000000000520c88 LR: c0000000004a3b34 CTR: 0000000000000000
REGS: c0000000f600a820 TRAP: 0700 Not tainted (4.3.0-rc5-13676-ga5e681d)
MSR: 8000000102029032 <SF,VEC,EE,ME,IR,DR,RI> CR: 24444884 XER: 00000000
CFAR: c0000000004a3b30 SOFTE: 1
GPR00: c0000000004a3b34 c0000000f600aaa0 c00000000108ac00 c0000000f5a808c0
GPR04: 0000000000000000 c0000000f600ae60 0000000000000000 0000000000000005
GPR08: 00000000000020a1 0000000000000001 c0000000f2b1f560 0000000000000030
GPR12: 0000000084842882 c00000000fdc0900 c0000000f600ae60 c0000000f070b800
GPR16: 0000000000000000 c0000000f3c8a000 0000000000000000 0000000000000049
GPR20: 0000000000000001 0000000000000001 c0000000f5aa01f8 0000000000000000
GPR24: 0f83e0f83e0f83e1 c0000000f5a808c0 c0000000f3c8d000 c000000000000000
GPR28: c0000000f600ae74 0000000000000001 c0000000f3c8d000 c0000000f5a808c0
NIP [c000000000520c88] .btrfs_tree_lock+0x48/0x2a0
LR [c0000000004a3b34] .btrfs_lock_root_node+0x44/0x80
Call Trace:
[c0000000f600aaa0] [c0000000f600ab80] 0xc0000000f600ab80 (unreliable)
[c0000000f600ab80] [c0000000004a3b34] .btrfs_lock_root_node+0x44/0x80
[c0000000f600ac00] [c0000000004a99dc] .btrfs_search_slot+0xa8c/0xc00
[c0000000f600ad40] [c0000000004ab878] .btrfs_insert_empty_items+0x98/0x120
[c0000000f600adf0] [c00000000050da44] .btrfs_finish_chunk_alloc+0x1d4/0x620
[c0000000f600af20] [c0000000004be854] .btrfs_create_pending_block_groups+0x1d4/0x2c0
[c0000000f600b020] [c0000000004bf188] .do_chunk_alloc+0x3c8/0x420
[c0000000f600b100] [c0000000004c27cc] .find_free_extent+0xbfc/0x1030
[c0000000f600b260] [c0000000004c2ce8] .btrfs_reserve_extent+0xe8/0x250
[c0000000f600b330] [c0000000004c2f90] .btrfs_alloc_tree_block+0x140/0x590
[c0000000f600b440] [c0000000004a47b4] .__btrfs_cow_block+0x124/0x780
[c0000000f600b530] [c0000000004a4fc0] .btrfs_cow_block+0xf0/0x250
[c0000000f600b5e0] [c0000000004a917c] .btrfs_search_slot+0x22c/0xc00
[c0000000f600b720] [c00000000050aa40] .btrfs_remove_chunk+0x1b0/0x9f0
[c0000000f600b850] [c0000000004c4e04] .btrfs_delete_unused_bgs+0x434/0x570
[c0000000f600b950] [c0000000004d3cb8] .close_ctree+0x2e8/0x3b0
[c0000000f600ba20] [c00000000049d178] .btrfs_put_super+0x18/0x30
[c0000000f600ba90] [c000000000243cd4] .generic_shutdown_super+0xa4/0x1a0
[c0000000f600bb10] [c0000000002441d8] .kill_anon_super+0x18/0x30
[c0000000f600bb90] [c00000000049c898] .btrfs_kill_super+0x18/0xc0
[c0000000f600bc10] [c0000000002444f8] .deactivate_locked_super+0x98/0xe0
[c0000000f600bc90] [c000000000269f94] .cleanup_mnt+0x54/0xa0
[c0000000f600bd10] [c0000000000bd744] .task_work_run+0xc4/0x100
[c0000000f600bdb0] [c000000000016334] .do_notify_resume+0x74/0x80
[c0000000f600be30] [c0000000000098b8] .ret_from_except_lite+0x64/0x68
Instruction dump:
fba1ffe8 fbc1fff0 fbe1fff8 7c791b78 f8010010 f821ff21 e94d0290 81030040
812a04e8 7d094a78 7d290034 5529d97e <0b090000> 3b400000 3be30050 3bc3004c
The above call trace is seen even on x86_64; albeit very rarely and that too
with nodesize set to 64k and with nospace_cache mount option being used.
The reason for the above call trace is,
btrfs_remove_chunk
check_system_chunk
Allocate chunk if required
For each physical stripe on underlying device,
btrfs_free_dev_extent
...
Take lock on Device tree's root node
btrfs_cow_block("dev tree's root node");
btrfs_reserve_extent
find_free_extent
index = BTRFS_RAID_DUP;
have_caching_bg = false;
When in LOOP_CACHING_NOWAIT state, Assume we find a block group
which is being cached; Hence have_caching_bg is set to true
When repeating the search for the next RAID index, we set
have_caching_bg to false.
Hence right after completing the LOOP_CACHING_NOWAIT state, we incorrectly
skip LOOP_CACHING_WAIT state and move to LOOP_ALLOC_CHUNK state where we
allocate a chunk and try to add entries corresponding to the chunk's physical
stripe into the device tree. When doing so the task deadlocks itself waiting
for the blocking lock on the root node of the device tree.
This commit fixes the issue by introducing a new local variable to help
indicate as to whether a block group of any RAID type is being cached.
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Even with quota disabled, generic/127 will trigger a kernel warning by
underflow data space info.
The bug is caused by buffered write, which in case of short copy, the
start parameter for btrfs_delalloc_release_space() is wrong, and
round_up/down() in btrfs_delalloc_release() extents the range to page
aligned, decreasing one more page than expected.
This patch will fix it by passing correct start.
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Hi,
Zhangqing Luo reported long boot times on a system with thousands of
LUNs when scsi-mq was enabled. He narrowed the problem down to
blk_mq_add_queue_tag_set, where every queue is frozen in order to set
the BLK_MQ_F_TAG_SHARED flag. Each added device will freeze all queues
added before it in sequence, which involves waiting for an RCU grace
period for each one. We don't need to do this. After the second queue
is added, only new queues need to be initialized with the shared tag.
We can do that by percolating the flag up to the blk_mq_tag_set, and
updating the newly added queue's hctxs if the flag is set.
This problem was introduced by commit 0d2602ca30 (blk-mq: improve
support for shared tags maps).
Reported-and-tested-by: Jason Luo <zhangqing.luo@oracle.com>
Reviewed-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Or Gerlitz says:
====================
Mellanox mlx5e driver update, Nov 3 2015
This series contains bunch of small fixes to the mlx5e driver from Achiad.
Changes from V0:
- removed the driver patch that dealt with IRQ affinity changes during
NAPI poll, as this is a generic problem which needs generic solution.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider vlan insertion impact on headers copy size also for LSO
packets.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit cd58c714ac "net/mlx5e: Disable client vlan TX acceleration".
Bring back client vlan insertion offload, the original
performance issue was found and fixed in the next patch.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case mlx5e_set_features() fails, return the failure status rather
than 0.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider MLX5E_MAX_NUM_CHANNELS @ethtool set/get_channels
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of storing the msix array index in eq->irqn (vecidx),
store the real irq number.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use jiffies rather than wait loop with msleep().
The wait loop didn't take into consideration time when the
process was not executing.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a configuration operation that involves closing and re-opening
resources (e.g RX/TX queue size change) fails at the re-opening stage
these resources will remain closed.
So when executing (following) configuration operations (e.g ifconfig
down) we cannot assume that these resources are available.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop unaligned dcache management functions as they are no longer used.
This reverts commit bd974240c9 ("xtensa: cache inquiry and
unaligned cache handling functions").
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
* pci/host-altera:
PCI: altera: Add Altera PCIe MSI driver
PCI: altera: Add Altera PCIe host controller driver
ARM: Add msi.h to Kbuild
* pci/host-designware:
PCI: designware: Make "clocks" and "clock-names" optional DT properties
PCI: designware: Make driver arch-agnostic
ARM/PCI: Replace pci_sys_data->align_resource with global function pointer
PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT
Revert "PCI: designware: Program ATU with untranslated address"
PCI: designware: Move calculation of bus addresses to DRA7xx
PCI: designware: Make "num-lanes" an optional DT property
PCI: designware: Require config accesses to be naturally aligned
PCI: designware: Simplify dw_pcie_cfg_read/write() interfaces
PCI: designware: Use exact access size in dw_pcie_cfg_read()
PCI: spear: Fix dw_pcie_cfg_read/write() usage
PCI: designware: Set up high part of MSI target address
PCI: designware: Make get_msi_addr() return phys_addr_t, not u32
PCI: designware: Implement multivector MSI IRQ setup
PCI: designware: Factor out MSI msg setup
PCI: Add msi_controller setup_irqs() method for special multivector setup
PCI: designware: Fix PORT_LOGIC_LINK_WIDTH_MASK
* pci/host-generic:
PCI: generic: Fix address window calculation for non-zero starting bus
PCI: generic: Pass starting bus number to pci_scan_root_bus()
PCI: generic: Allow multiple hosts with different map_bus() methods
arm64: dts: Drop linux,pci-probe-only from the Seattle DTS
powerpc/PCI: Fix lookup of linux,pci-probe-only property
PCI: generic: Fix lookup of linux,pci-probe-only property
of/pci: Add of_pci_check_probe_only to parse "linux,pci-probe-only"
* pci/host-imx6:
PCI: imx6: Add PCIE_PHY_RX_ASIC_OUT_VALID definition
PCI: imx6: Return real error code from imx6_add_pcie_port()
* pci/host-iproc:
PCI: iproc: Fix header comment "Corporation" misspelling
PCI: iproc: Add outbound mapping support
PCI: iproc: Update PCIe device tree bindings
PCI: iproc: Improve link detection logic
PCI: iproc: Fix PCIe reset logic
PCI: iproc: Call pci_fixup_irqs() for ARM64 as well as ARM
PCI: iproc: Remove unused struct iproc_pcie.irqs[]
PCI: iproc: Fix code comment to match code
* pci/host-mvebu:
PCI: mvebu: Remove code restricting accesses to slot 0
PCI: mvebu: Add PCI Express root complex capability block
PCI: mvebu: Improve clock/reset handling
PCI: mvebu: Use gpio_desc to carry around gpio
PCI: mvebu: Use devm_kcalloc() to allocate an array
PCI: mvebu: Use gpio_set_value_cansleep()
PCI: mvebu: Split port parsing and resource claiming from port setup
PCI: mvebu: Fix memory leaks and refcount leaks
PCI: mvebu: Move port parsing and resource claiming to separate function
PCI: mvebu: Use port->name rather than "PCIe%d.%d"
PCI: mvebu: Report full node name when reporting a DT error
PCI: mvebu: Use for_each_available_child_of_node() to walk child nodes
PCI: mvebu: Use of_get_available_child_count()
PCI: mvebu: Use exact config access size; don't read/modify/write
PCI: mvebu: Return zero for reserved or unimplemented config space
* pci/host-rcar:
PCI: rcar: Fix I/O offset for multiple host bridges
PCI: rcar: Set root bus nr to that provided in DT
PCI: rcar: Remove dependency on ARM-specific struct hw_pci
PCI: rcar: Make PCI aware of the I/O resources
PCI: rcar: Build pcie-rcar.c only on ARM
PCI: rcar: Build pci-rcar-gen2.c only on ARM
* pci/host-tegra:
PCI: tegra: Wrap static pgprot_t initializer with __pgprot()
* pci/host-xgene:
PCI/MSI: xgene: Remove msi_controller assignment
Add Altera PCIe MSI driver. This soft IP supports a configurable number of
vectors, which is a DTS parameter.
[bhelgaas: Kconfig depend on PCIE_ALTERA, typos, whitespace]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
There are no .bootstrap or .ResetVector.text sections linked to the
vmlinux image, drop these sections from vmlinux.ld.S. Drop
RESET_VECTOR_VADDR definition only used for .ResetVector.text.
Drop remapped copies of primary and secondary reset vectors, as modern
gdb don't have problems stepping through instructions at arbitrary
locations. Drop corresponding sections from the corresponding linker
scripts.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
There are multiple factors adding to the issue in different
configurations:
- commit 17290231df ("xtensa: add fixup for double exception raised
in window overflow") added function window_overflow_restore_a0_fixup to
double exception vector overlapping reset vector location of secondary
processor cores.
- on MMUv2 cores RESET_VECTOR1_VADDR may point to uncached kernel memory
making code overlapping depend on cache type and size, so that without
cache or with WT cache reset vector code overwrites double exception
code, making issue even harder to detect.
- on MMUv3 cores RESET_VECTOR1_VADDR may point to unmapped area, as
MMUv3 cores change virtual address map to match MMUv2 layout, but
reset vector virtual address is given for the original MMUv3 mapping.
- physical memory region of the secondary reset vector is not reserved
in the physical memory map, and thus may be allocated and overwritten
at arbitrary moment.
Fix it as follows:
- move window_overflow_restore_a0_fixup code to .text section.
- define RESET_VECTOR1_VADDR so that it points to reset vector in the
cacheable MMUv2 map for cores with MMU.
- reserve reset vector region in the physical memory map. Drop separate
literal section and build mxhead.S with text section literals.
Cc: <stable@vger.kernel.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Make maximal memory allocation order configurable, so that drivers could
allocate huge buffers when they need to.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The external interrupts for runtime instrumentation buffer-full
and runtime instrumentation halted are unused and have no current
user. Remove the support and ignore the second parameter of the
s390_runtime_instr system call from now on.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
cio_validate_io_subchannel() and cio_validate_msg_subchannel() are
identical, as the called functions already take care about the
differences between subchannel types.
Just inline the code into the only user,
cio_validate_subchannel(), instead.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ret variable is always set by the fn function.
There is no need to initialize it.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Reviewed-By: Sascha Silbe <silbe@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Depending on the gcc version we can use builtin_bswap instead of
architecture functions. Doing so is better than the inline assembly
version of load reverse for two reasons:
- the sequence of load reversed, apply constant mask, save reversed can
be optimized to load, apply reversed mask, save
- builtins are slightly better to optimize e.g. gcc instruction
scheduler cannot optimize grouping on inline assemblies.
To enable set we have to ARCH_USE_BUILTIN_BSWAP.
bloat-o-meter results:
add/remove: 1/1 grow/shrink: 75/533 up/down: 1711/-9394 (-7683)
Suggested-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Path verification is either done via dasd_eckd_read_conf() which is
triggered during online processing and resume or via
do_path_verification_work() which is triggered after path events.
The dasd_eckd_read_conf() version added paths unconditionally and did
not check if the path mask was empty. This led to devices having the
disconnected stop flag set but a valid path mask. So they where not
working although they had paths validated successfully. After a resume
this state could even not be solved with additional paths added.
Fix by checking for an empty path mask in dasd_eckd_read_conf() and
clearing the device stop bits for a newly added channel path.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For a valid PAV assignment the DASD driver needs to notice possibly
changed configuration data. Thus the failing of read configuration
data should also fail the device restore to prevent invalid PAV
assignment. The failed device may get restored after additional paths
get available later on.
If the restore fails after the device was added to the lcu alias
handling it needs to be removed from the alias handling before exiting
the restore function.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The configuration data is stored per path and also the first valid
configuration data per device. When dasd_eckd_read_conf is called
again after a path got lost the device configuration data is cleared
but possibly not the per path configuration data. This might lead to a
double free when the lost path gets operational again.
Fix by clearing all per path configuration data when the first valid
configuration data is received and stored.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
git commit 155e839a81
"s390/kernel: dynamically allocate FP register save area"
introduced a regression in regard to ptrace.
If the vector register extension is not present or unused the
ptrace peek of a floating pointer register return incorrect data
and the ptrace poke to a floating pointer register overwrites the
task structure starting at task->thread.fpu.fprs.
Cc: stable@kernel.org # v4.3
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The pad handling code introduced for the Cintiq Companion 2 (f7acb55)
looks at the wrong bytes in the report when deciding whether ABS_MISC
should be sent. This does not cause any issues with the X driver now
that the pen and pad have been split to separate devices, but is
incorrect and has caused issues when backporting to distros with pre-
3.17 kernels.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When support for the Cintiq Companion Hybrid and Cintiq Companion 2 was
added (36d3c51 and f7acb55), the 'wacom_query_tablet_data' function was
updated to include references to CINTIQ_HYBRID and CINTIQ_COMPANION_2
with the thought that they were necessary to switch the touch interface
into the proper mode. This is unnecessary, however, since those types
are only ever associated with the pen interface -- the touch interfaces
are either CINTIQ_24HDT or HID_GENERIC. To avoid confusion in the future,
we remove the unnecessary CINTIQ_HYBRID and CINTIQ_COMPANION_2 conditions.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Watchdog ping return errors are ignored by watchdog core,
Whatchdog daemon should be informed about possible hardware error or
underlaying device driver get unregistered.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The current code uses 'wdd', wddev', and 'watchdog' as variable names
for struct watchdog_device. This is confusing and makes it difficult
to enhance the code. Replace it all with 'wdd'.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Timo Kokkonen <timo.kokkonen@offcode.fi>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Up to now, a new timeout value is only evaluated against min_timeout
if max_timeout is provided. This does not really make sense; a driver
can have a minimum timeout even if it does not have a maximum timeout.
Ensure that it is not smaller than min_timeout, even if max_timeout
is not set.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Currently, cfg80211 rejects updates of AID and listen interval parameters
for existing entries. This information is known only at association stage
and as a result it's impossible to update entries that were added
unassociated.
Fix this by allowing updates of these properies for stations that the
driver (or mac80211) assigned unassociated state.
This then fixes mac80211's use of NL80211_FEATURE_FULL_AP_CLIENT_STATE.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel context driver operations can sleep, so add might_sleep()
and document this.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow distinguishing the non-station case from the case of a
station without rates, by using -1 for the non-station case.
This value cannot be reached with a station since that many
legacy rates don't exist.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As WMM is required for HT/VHT operation, treat bad WMM parameters
more gracefully by falling back to default parameters instead of
not using WMM assocation. This makes it possible to still use HT
or VHT, although potentially with reduced quality of service due
to unintended WMM parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disabling WMM has a huge impact these days. It implies that
HT and VHT will be disabled which means that the throughput
will be drammatically reduced.
Since the AIFSN is a transmission parameter, we can play a
bit and fix it up to make it compliant with the 802.11
specification which requires it to be at least 2.
Increasing it from 1 to 2 will slightly reduce the
likelyhood to get a transmission opportunity compared to
other clients that would accept to set AIFSN=1, but at
least it will allow HT and VHT which is a huge gain.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function currently determines this value, for use in bss_info.qos,
based on the interface type itself. Make it a parameter instead and
set it with the same logic for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous patch changed mac80211 to always report an event
after a CQM RSSI reconfiguration. Document that as expected
behaviour in both the cfg80211 and mac80211 API.
Currently, iwlmvm already implements that behaviour; the other
drivers implementing CQM RSSI events may have to be changed.
This behaviour lets userspace know what the current state is
without relying on querying the data which is racy.
Reviewed-by: Sharon, Sara <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
llid_in_use needs to be limited to stations of the same VIF, otherwise it
will cause a NULL deref as the sta_info of non-mesh-VIFs don't have
sta->mesh set.
Steps to reproduce:
modprobe mac80211_hwsim channels=2
iw phy phy0 interface add ibss0 type ibss
iw phy phy0 interface add mesh0 type mp
iw phy phy1 interface add ibss1 type ibss
iw phy phy1 interface add mesh1 type mp
ip link set ibss0 up
ip link set mesh0 up
ip link set ibss1 up
ip link set mesh1 up
iw dev ibss0 ibss join foo 2412
iw dev ibss1 ibss join foo 2412
# Ensure that ibss0 and ibss1 are actually associated; I often need to
# leave and join the cell on ibss1 a second time.
iw dev mesh0 mesh join bar
iw dev mesh1 mesh join bar # crash
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When 11n peers performs a TDLS connection on a legacy BSS, the HT
operation IE must be specified according to IEEE802.11-2012 section
9.23.3.2. Otherwise HT-protection is compromised and the medium becomes
noisy for both the TDLS and the BSS links.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
