libata currently imposes a UDMA5 max transfer rate and 200 sector max
transfer size for SATA devices that sit behind a pata-sata bridge. Lots
of devices have known good bridges that don't need this limit applied.
The MTRON SSD disks are such devices. Transfer rates are increased by
20-30% with the restriction removed.
So add a "blacklist" entry for the MTRON devices, with a flag indicating
that the bridge is known good.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.
The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus. This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.
The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.
Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device. This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.
The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY. This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers. As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).
Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar. But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.
We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers. If one is found the ID of its platform device is saved in the
gianfar's platform data.
A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID. The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Impact: fix crashes that can occur in NMI handlers, if their code is modified
Modifying code is something that needs special care. On SMP boxes,
if code that is being modified is also being executed on another CPU,
that CPU will have undefined results.
The dynamic ftrace uses kstop_machine to make the system act like a
uniprocessor system. But this does not address NMIs, that can still
run on other CPUs.
One approach to handle this is to make all code that are used by NMIs
not be traced. But NMIs can call notifiers that spread throughout the
kernel and this will be very hard to maintain, and the chance of missing
a function is very high.
The approach that this patch takes is to have the NMIs modify the code
if the modification is taking place. The way this works is that just
writing to code executing on another CPU is not harmful if what is
written is the same as what exists.
Two buffers are used: an IP buffer and a "code" buffer.
The steps that the patcher takes are:
1) Put in the instruction pointer into the IP buffer
and the new code into the "code" buffer.
2) Set a flag that says we are modifying code
3) Wait for any running NMIs to finish.
4) Write the code
5) clear the flag.
6) Wait for any running NMIs to finish.
If an NMI is executed, it will also write the pending code.
Multiple writes are OK, because what is being written is the same.
Then the patcher must wait for all running NMIs to finish before
going to the next line that must be patched.
This is basically the RCU approach to code modification.
Thanks to Ingo Molnar for suggesting the idea, and to Arjan van de Ven
for his guidence on what is safe and what is not.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
Fix incompatibility with versions of Perl less than 5.6.0
kbuild: do not include arch/<ARCH>/include/asm in find-sources twice.
kbuild: tag with git revision when git describe is missing
kbuild: prevent modpost from looking for a .cmd file for a static library linked into a module
kbuild: fix KBUILD_EXTRA_SYMBOLS
adjust init section definitions
scripts/checksyscalls.sh: fix for non-gnu sed
scripts/package: don't break if %{_smp_mflags} isn't set
kbuild: setlocalversion: dont include svn change count
kbuild: improve check-symlink
kbuild: mkspec - fix build rpm
Impact: improve documentation
It's nice to say that mutex_trylock follows the spin_trylock convention.
It's a lot nicer if the comment also says which that is... make it so.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: Fix WM9713 ALC Decay Time name
ALSA: ASoC: Fix some minor errors in mpc5200 psc i2s driver
ALSA: ASoC: Fix mono controls after conversion to support full int masks
ALSA: sound/ice1712: indentation & braces disagree - add braces
ALSA: usb - Add quirk for Edirol UA-25EX advanced modes
sound: struct device - replace bus_id with dev_name(), dev_set_name()
ALSA: hda - Add reboot notifier
ALSA: Warn when control names are truncated
ALSA: intel8x0 - add Dell Optiplex GX620 (AD1981B) to AC97 clock whitelist
ALSA: hda - Fix SPDIF mute on IDT/STAC codecs
ALSA: hda: Add HDA vendor ID for Wolfson Microelectronics
ALSA: hda - Add another HP model for AD1884A
Fix compile error below:
LD drivers/spi/built-in.o
CC [M] drivers/spi/spi_gpio.o
In file included from drivers/spi/spi_gpio.c:26:
include/linux/spi/spi_bitbang.h:23: error: field `work' has incomplete type
make[2]: *** [drivers/spi/spi_gpio.o] Error 1
make[1]: *** [drivers/spi] Error 2
make: *** [drivers] Error 2
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junjiro R. Okajima reported a problem where knfsd crashes if you are
using it to export shmemfs objects and run strict overcommit. In this
situation the current->mm based modifier to the overcommit goes through a
NULL pointer.
We could simply check for NULL and skip the modifier but we've caught
other real bugs in the past from mm being NULL here - cases where we did
need a valid mm set up (eg the exec bug about a year ago).
To preserve the checks and get the logic we want shuffle the checking
around and add a new helper to the vm_ security wrappers
Also fix a current->mm reference in nommu that should use the passed mm
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix build]
Reported-by: Junjiro R. Okajima <hooanon05@yahoo.co.jp>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Put the kernel-doc for might_sleep() _immediately_ before the macro
(no intervening lines). Otherwise kernel-doc complains like so:
Warning(linux-2.6.27-rc3-git2//include/linux/kernel.h:129): No description found for parameter 'file'
Warning(linux-2.6.27-rc3-git2//include/linux/kernel.h:129): No description found for parameter 'line'
because kernel-doc is looking at the wrong function prototype (i.e.,
__might_sleep). [Yes, I have a todo note to myself to check/warn for that
inconsistency in scripts/kernel-doc.]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nothing uses prepare_write or commit_write. Remove them from the tree
completely.
[akpm@linux-foundation.org: schedule simple_prepare_write() for unexporting]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't duplicate the implementation of thaw_process().
[akpm@linux-foundation.org: make __thaw_process() static]
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Acked-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By default, non-privileged tasks can only mlock() a small amount of
memory to avoid a DoS attack by ordinary users. The Linux kernel
defaulted to 32k (on a 4k page size system) to accommodate the needs of
gpg.
However, newer gpg2 needs 64k in various circumstances and otherwise
fails miserably, see bnc#329675.
Change the default to 64k, and make it more agnostic to PAGE_SIZE.
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i.e. echo 6 59 >/sys/kernel/debug/soc-audio.0/codec_reg
will set register 0x06 to a value of 0x59.
Also, pop_time debugfs interface setup is moved so that it
is setup in the same function as codec_reg
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When ASoC was converted to support full int width masks SOC_SINGLE_VALUE()
omitted the assignment of rshift, causing the control operatins to report
some mono controls as stereo. This happened to work some of the time due
to a confusion between shift and min in snd_soc_info_volsw().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move mci.h to new position in arch/arm/plat-s3c24xx/include/plat
ready to clean out old include directories.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move plat/regs-spi.h to arch/arm/plat-s3c/include/plat ready
ready to clean out old include directories.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the udc headers to the proper home in
arch/arm/plat-s3c24xx/include/plat ready to clean out
the old include directories.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
To allow XFS to combine the XFS and linux inodes into a single
structure, we need to drive inode lookup from the XFS inode cache,
not the generic inode cache. This means that we need initialise a
struct inode from a context outside alloc_inode() as it is no longer
used by XFS.
After inode allocation and initialisation, we need to add the inode
to the superblock list, the in-use list, hash it and do some
accounting. This all needs to be done with the inode_lock held and
there are already several places in fs/inode.c that do this list
manipulation. Factor out the common code, add a locking wrapper and
export the function so ti can be called from XFS.
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
To allow XFS to combine the XFS and linux inodes into a single
structure, we need to drive inode lookup from the XFS inode cache,
not the generic inode cache. This means that we need initialise a
struct inode from a context outside alloc_inode() as it is no longer
used by XFS.
Factor and export the struct inode initialisation code from
alloc_inode() to inode_init_always() as a counterpart to
inode_init_once(). i.e. we have to call this init function for each
inode instantiation (always), as opposed inode_init_once() which is
only called on slab object instantiation (once).
Signed-off-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Add rodata equivalents for assembly use, and fix the section attributes
used by __REFCONST.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Corey Minyard found a race added in commit 271b72c7fa
(udp: RCU handling for Unicast packets.)
"If the socket is moved from one list to another list in-between the
time the hash is calculated and the next field is accessed, and the
socket has moved to the end of the new list, the traversal will not
complete properly on the list it should have, since the socket will
be on the end of the new list and there's not a way to tell it's on a
new list and restart the list traversal. I think that this can be
solved by pre-fetching the "next" field (with proper barriers) before
checking the hash."
This patch corrects this problem, introducing a new
sk_for_each_rcu_safenext() macro.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Goals are :
1) Optimizing handling of incoming Unicast UDP frames, so that no memory
writes should happen in the fast path.
Note: Multicasts and broadcasts still will need to take a lock,
because doing a full lockless lookup in this case is difficult.
2) No expensive operations in the socket bind/unhash phases :
- No expensive synchronize_rcu() calls.
- No added rcu_head in socket structure, increasing memory needs,
but more important, forcing us to use call_rcu() calls,
that have the bad property of making sockets structure cold.
(rcu grace period between socket freeing and its potential reuse
make this socket being cold in CPU cache).
David did a previous patch using call_rcu() and noticed a 20%
impact on TCP connection rates.
Quoting Cristopher Lameter :
"Right. That results in cacheline cooldown. You'd want to recycle
the object as they are cache hot on a per cpu basis. That is screwed
up by the delayed regular rcu processing. We have seen multiple
regressions due to cacheline cooldown.
The only choice in cacheline hot sensitive areas is to deal with the
complexity that comes with SLAB_DESTROY_BY_RCU or give up on RCU."
- Because udp sockets are allocated from dedicated kmem_cache,
use of SLAB_DESTROY_BY_RCU can help here.
Theory of operation :
---------------------
As the lookup is lockfree (using rcu_read_lock()/rcu_read_unlock()),
special attention must be taken by readers and writers.
Use of SLAB_DESTROY_BY_RCU is tricky too, because a socket can be freed,
reused, inserted in a different chain or in worst case in the same chain
while readers could do lookups in the same time.
In order to avoid loops, a reader must check each socket found in a chain
really belongs to the chain the reader was traversing. If it finds a
mismatch, lookup must start again at the begining. This *restart* loop
is the reason we had to use rdlock for the multicast case, because
we dont want to send same message several times to the same socket.
We use RCU only for fast path.
Thus, /proc/net/udp still takes spinlocks.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP sockets are hashed in a 128 slots hash table.
This hash table is protected by *one* rwlock.
This rwlock is readlocked each time an incoming UDP message is handled.
This rwlock is writelocked each time a socket must be inserted in
hash table (bind time), or deleted from this table (close time)
This is not scalable on SMP machines :
1) Even in read mode, lock() and unlock() are atomic operations and
must dirty a contended cache line, shared by all cpus.
2) A writer might be starved if many readers are 'in flight'. This can
happen on a machine with some NIC receiving many UDP messages. User
process can be delayed a long time at socket creation/dismantle time.
This patch prepares RCU migration, by introducing 'struct udp_table
and struct udp_hslot', and using one spinlock per chain, to reduce
contention on central rwlock.
Introducing one spinlock per chain reduces latencies, for port
randomization on heavily loaded UDP servers. This also speedup
bindings to specific ports.
udp_lib_unhash() was uninlined, becoming to big.
Some cleanups were done to ease review of following patch
(RCUification of UDP Unicast lookups)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Open code NIP6_FMT in the one call inside sscanf and one user
of NIP6() that could use %p6 in the netfilter code.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct hid_device_id contains hidden padding which is bad for cross
compiling. Make the padding explicit and consistent across
architectures.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add new_mapping() implementation to the netlink xfrm_mgr to notify
address/port changes detected in UDP encapsulated ESP packets.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
ftrace: fix current_tracer error return
tracing: fix a build error on alpha
ftrace: use a real variable for ftrace_nop in x86
tracing/ftrace: make boot tracer select the sched_switch tracer
tracepoint: check if the probe has been registered
asm-generic: define DIE_OOPS in asm-generic
trace: fix printk warning for u64
ftrace: warning in kernel/trace/ftrace.c
ftrace: fix build failure
ftrace, powerpc, sparc64, x86: remove notrace from arch ftrace file
ftrace: remove ftrace hash
ftrace: remove mcount set
ftrace: remove daemon
ftrace: disable dynamic ftrace for all archs that use daemon
ftrace: add ftrace warn on to disable ftrace
ftrace: only have ftrace_kill atomic
ftrace: use probe_kernel
ftrace: comment arch ftrace code
ftrace: return error on failed modified text.
ftrace: dynamic ftrace process only text section
...
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix documentation reference for sched_min_granularity_ns
sched: virtual time buddy preemption
sched: re-instate vruntime based wakeup preemption
sched: weaken sync hint
sched: more accurate min_vruntime accounting
sched: fix a find_busiest_group buglet
sched: add CONFIG_SMP consistency
Every call of kvm_set_irq() should offer an irq_source_id, which is
allocated by kvm_request_irq_source_id(). Based on irq_source_id, we
identify the irq source and implement logical OR for shared level
interrupts.
The allocated irq_source_id can be freed by kvm_free_irq_source_id().
Currently, we support at most sizeof(unsigned long) different irq sources.
[Amit: - rebase to kvm.git HEAD
- move definition of KVM_USERSPACE_IRQ_SOURCE_ID to common file
- move kvm_request_irq_source_id to the update_irq ioctl]
[Xiantao: - Add kvm/ia64 stuff and make it work for kvm/ia64 guests]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
