I got the following oops during interface ifup. Unfortunately its not
easily reproducable so I cant say for sure that my fix fixes this
problem, but I am confident and I think its correct anyway:
<2>kernel BUG at /space/kvm/drivers/virtio/virtio_ring.c:234!
<4>illegal operation: 0001 [#1] PREEMPT SMP
<4>Modules linked in:
<4>CPU: 0 Not tainted 2.6.24zlive-guest-07293-gf1ca151-dirty #91
<4>Process swapper (pid: 0, task: 0000000000800938, ksp: 000000000084ddb8)
<4>Krnl PSW : 0404300180000000 0000000000466374 (vring_disable_cb+0x30/0x34)
<4> R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:3 PM:0 EA:3
<4>Krnl GPRS: 0000000000000001 0000000000000001 0000000010003800 0000000000466344
<4> 000000000e980900 00000000008848b0 000000000084e748 0000000000000000
<4> 000000000087b300 0000000000001237 0000000000001237 000000000f85bdd8
<4> 000000000e980920 00000000001137c0 0000000000464754 000000000f85bdd8
<4>Krnl Code: 0000000000466368: e3b0b0700004 lg %r11,112(%r11)
<4> 000000000046636e: 07fe bcr 15,%r14
<4> 0000000000466370: a7f40001 brc 15,466372
<4> >0000000000466374: a7f4fff6 brc 15,466360
<4> 0000000000466378: eb7ff0500024 stmg %r7,%r15,80(%r15)
<4> 000000000046637e: a7f13e00 tmll %r15,15872
<4> 0000000000466382: b90400ef lgr %r14,%r15
<4> 0000000000466386: a7840001 brc 8,466388
<4>Call Trace:
<4>([<000201500f85c000>] 0x201500f85c000)
<4> [<0000000000466556>] vring_interrupt+0x72/0x88
<4> [<00000000004801a0>] kvm_extint_handler+0x34/0x44
<4> [<000000000010d22c>] do_extint+0xbc/0xf8
<4> [<0000000000113f98>] ext_no_vtime+0x16/0x1a
<4> [<000000000010a182>] cpu_idle+0x216/0x238
<4>([<000000000010a162>] cpu_idle+0x1f6/0x238)
<4> [<0000000000568656>] rest_init+0xaa/0xb8
<4> [<000000000084ee2c>] start_kernel+0x3fc/0x490
<4> [<0000000000100020>] _stext+0x20/0x80
<4>
<4> <0>Kernel panic - not syncing: Fatal exception in interrupt
<4>
After looking at the code and the dump I think the following scenario
happened: Ifup was running on cpu2 and the interrupt arrived on cpu0.
Now virtnet_open on cpu 2 managed to execute napi_enable and disable_cb
but did not execute rx_schedule. Meanwhile on cpu 0 skb_recv_done was
called by vring_interrupt, executed netif_rx_schedule_prep, which
succeeded and therefore called disable_cb. This triggered the BUG_ON,
as interrupts were already disabled by cpu 2.
I think the proper solution is to make the call to disable_cb depend on
the atomic update of NAPI_STATE_SCHED by using netif_rx_schedule_prep
in the same way as skb_recv_done.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PHY Lib now uses mutexes instead of spin_locks. ucc_geth
and gianfar both grab the locks in their mdio_reset functions,
so they need to use mutex_(un)lock instead. This was not caught
until someone tested it on an SMP system.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Various registers need to be preserved before resetting the device.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver needs to ack only the phy status bits that it is currently
handling and preserve the other bits for the other handlers. For
example, when reading/writing from the phy, it should not clear the link
change interrupt bit. This will cause a missing link change interrupt.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the issue where the transmitter and receiver must be
restarted when applying new changes to certain registers.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No available servers is more an error message than something informational. It
should also be rate-limited, else we're going to flood our logs on a busy
director, if all real servers are out of order with a weight of zero.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
... thus decreasing checkpatch.pl errors to 0.
Bart:
- remove needless function prototypes while at it
- remove needless parentheses while at it
- add missing KERN_ level to ide_tape_probe()
- other minor fixups
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This function was being used only at one place so fold it in there.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Shorten some member names not too aggressively since this driver might be gone
anyway soon.
Bart:
- minor fixes
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
- last_frame_position: only being written to once
- firmware_revision, product_id, vendor_id: used once, remove from struct
idetape_tape_t and deal with them locally
- firmware_revision_num: only written to once
- tape_still_time_begin: completely unused
- tape_still_time: never written to; remove corresponding code chunk
- uncontrolled_last_pipeline_head: only once written to
- blocks_in_buffer: only written to
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... by adding a new typedef function pointer idetape_io_buf in order to call
the proper buffer i/o handler depending on the data direction.
Bart:
- move idetape_io_buf before idetape_pc_intr() comment
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
tape->speed_control is set to 1 in idetape_setup(), but, in calculate_speeds()
its value is tested for being 0, 1, or 2. Remove the if-branches where
tape->speed_control != 1 since they are never executed. Also, rename
calculate_speeds() by adding driver's prefix as is with the other function
names.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes resulting from this patch.
Bart:
- remove needless "!!"
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Teach the debug logging macro to differentiate between log levels based on the
type of debug level enabled specifically instead of a threshold-based one.
Thus, convert tape->debug_level to a bitmask that is written to over /proc.
Also,
- cleanup and simplify the debug macro thus removing a lot of code lines,
- get rid of unused debug levels,
- adjust the loglevel at several places where it was simply missing (e.g.
idetape_chrdev_open())
- move the tape ptr initialization up in idetape_chrdev_open() so that we can
use it in the debug_log macro earlier in the function.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide-cris.c:
* Add cris_setup_ports() helper and use it instead of ide_setup_ports()
(fixes random value being set in ->io_ports[IDE_IRQ_OFFSET]).
buddha.c:
* Add buddha_setup_ports() helper and use it instead of ide_setup_ports().
falconide.c:
* Add falconide_setup_ports() helper and use it instead of ide_setup_ports(),
also fix return value of falconide_init() while at it.
gayle.c:
* Add gayle_setup_ports() helper and use it instead of ide_setup_ports().
macide.c:
* Add macide_setup_ports() helper and use it instead of ide_setup_ports()
(fixes incorrect value being set in ->io_ports[IDE_IRQ_OFFSET]).
q40ide.c:
* Fix q40_ide_setup_ports() comments.
ide.c:
* Remove no longer needed ide_setup_ports().
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Replace incorrect CONFIG_BLK_DEV_IDE #ifdef in
check_media_bay() by CONFIG_MAC_FLOPPY one.
* Replace incorrect CONFIG_BLK_DEV_IDE #ifdef-s by
CONFIG_BLK_DEV_IDE_PMAC ones.
* check_media_bay() is used only by drivers/block/swim3.c
so make this function available only if CONFIG_MAC_FLOPPY
is defined.
* check_media_bay_by_base() and media_bay_set_ide_infos()
are used only by drivers/ide/ppc/pmac.c so so make these
functions available only if CONFIG_MAC_FLOPPY is defined.
v2:
* Remove ifdefs from function prototypes. (Andrew Morton)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
with module_param macro, the __setup code can be killed now:
const __setup("all-generic-ide", ide_generic_all_on);
and the module name "generic.ko" is not descriptive to its functionality,
can be changed in Makefile, the "ide-pci-generic.ko" is better.
the ide-pci-generic.all-generic-ide parameter also documented
in Documentation/kernel-parameters.txt
Signed-off-by: Denis Cheng <crquan@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drivers/ide/legacy/hd.c: In function 'hd_request':
drivers/ide/legacy/hd.c:424: warning: 'stat' may be used uninitialized in this function
gcc is being stupid.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drivers/ide/ide-acpi.c: In function 'ide_acpi_init':
drivers/ide/ide-acpi.c:175: warning: 'dev_handle' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is Palmchip BK3710 IDE controller support.
The IDE controller logic supports PIO, MultiWord-DMA and Ultra-DMA modes.
Supports interface to Compact Flash (CF) configured in True-IDE mode.
Bart:
- remove dead code
- fix ide_hwif_setup_dma() build problem
Signed-off-by: Anton Salnikov <asalnikov@ru.mvista.com>
Reviewed-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Tuesday 05 February 2008, Linus Torvalds wrote:
>
> On Sat, 2 Feb 2008, Bartlomiej Zolnierkiewicz wrote:
> >
> > * next part of IDE probing code re-organization saga
> > (that would be me)
>
> This seems to cause very irritating and bogus messages for me:
>
> Probing IDE interface ide0...
> Probing IDE interface ide1...
> ide2: I/O resource 0x0-0x7 not free.
> ide2: ports already in use, skipping probe
> ide3: I/O resource 0x0-0x7 not free.
> ide3: ports already in use, skipping probe
> ide4: I/O resource 0x0-0x7 not free.
> ide4: ports already in use, skipping probe
> ide5: I/O resource 0x0-0x7 not free.
> ide5: ports already in use, skipping probe
> ide6: I/O resource 0x0-0x7 not free.
> ide6: ports already in use, skipping probe
> ide7: I/O resource 0x0-0x7 not free.
> ide7: ports already in use, skipping probe
> ide8: I/O resource 0x0-0x7 not free.
> ide8: ports already in use, skipping probe
> ide9: I/O resource 0x0-0x7 not free.
> ide9: ports already in use, skipping probe
>
> and that's just totally bogus. It shouldn't even request that region,
> since it's not been allocated!
The commit 139ddfcab5 ("ide: move handling of
I/O resources out of ide_probe_port()") changed the ordering of hwif->noprobe
check vs ide_hwif_request_regions() call (so that we now reserve I/O regions
before checking for hwif->noprobe). However ide-generic host driver depended
on hwif->noprobe to be set for skipping probing of empty ide_hwifs[] slots.
Fix it by passing only indexes of non-empty slots to ide_device_add_all()
from ide_generic_init().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
When CONFIG_PROC_FS is not set and CONFIG_PPPOL2TP is set,
we have the following warning in build:
drivers/net/pppol2tp.c: In function 'pppol2tp_init':
drivers/net/pppol2tp.c:2472: warning: label
'out_unregister_pppox_proto' defined but not used
This patches fixes this warning by adding appropriate #ifdef.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Required by next patch to use it from the flow classifier.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we're using fls(), we need to check whether the value is
non-zero first.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/em_meta.c: In function 'meta_int_vlan_tag':
net/sched/em_meta.c:179: warning: 'tag' may be used uninitialized in this function
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
smbfs is a bit buggy and has no maintainer. Change it to shout at the user on
the first five mount attempts - tell them to switch to CIFS.
Come December we'll mark it BROKEN and see what happens.
[olecom@flower.upol.cz: documentation update]
Cc: Urban Widmark <urban@teststation.com>
Acked-by: Steven French <sfrench@us.ibm.com>
Signed-off-by: Oleg Verych <olecom@flower.upol.cz>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When change_page_attr splits a large page on x86_32 (without PAE), it is
currently corrupting every process's page directory: fix that by removing
the thinko which passes down a physical instead of a virtual address.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This checks if the DMA address is bigger than what the controller can manage.
It will reallocate the buffers in the GFP_DMA zone in that case.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
