Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This extends OD (OverDrive) support to the non-Powerplay code paths.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This extends dpm clock level selection to the non-powerplay code paths.
This interface can be used to select individual clock levels.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Based on Alex's patches this enables GFX PG on CZ.
Tested with xonotic-glx/glxgears/supertuxkart and idle desktop.
Also read-back registers via umr for verificiation that the bits
are truly enabled.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This implements sclk overdrive(OD) overclocking support for Polaris10,
and the maximum overdrive percentage is 20.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This implements sclk overdrive(OD) overclocking support for Tonga,
and the maximum overdrive percentage is 20.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This implements sclk overdrive(OD) overclocking support for Fiji,
and the maximum overdrive percentage is 20.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a new sysfs entry pp_sclk_od to support sclk overdrive(OD) overclocking,
the entry is read/write, the value of input/output is an integer which is the
over percentage of the highest sclk.
v2: drop extra semicolon
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The power tables on some variants require different firmware.
This may fix stability issues on some newer CI parts.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=91880
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The power tables on some variants require different firmware.
This may fix stability issues on some newer SI parts.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The power tables on some variants require different firmware.
This fixes stability issues on some newer CI parts.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=91880
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This help fix reloading driver hang issue of SDMA
ring.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some Kabylake SKUs are going to use Kabypoint PCH.
It is mainly for Halo and DT ones.
>From our specs it doesn't seem that KBP brings
any change on the display south engine. So let's consider
this as a continuation of SunrisePoint, i.e., SPT+.
Since it is easy to get confused by a letter change:
KBL = Kabylake - CPU/GPU codename.
KBP = Kabypoint - PCH codename.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96826
Link: http://patchwork.freedesktop.org/patch/msgid/1467418032-15167-1-git-send-email-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This patch applies WaMediaPoolStateCmdInWABB which fixes
a problem with the restoration of thread counts on resuming
from RC6.
References: HSD#2137167
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467709290-5941-1-git-send-email-tim.gore@intel.com
Move the encoder cloning check to happen earlier in the modeset. The
main benefit will be that the debug output from a failed modeset will
be less confusing as output_types can not indicate an invalid
configuration during the later computation stages.
For instance, what happened to me was kms_setmode was attempting one
of its invalid cloning checks during which it asked for DP+VGA cloning
on HSW. In this case the DP .compute_config() was executed after
the FDI .compute_config() leaving the DP link clock (1.62 in this case)
in port_clock, and then later the FDI BW computation tried to use that
as the FDI link clock (which should always be 2.7). 1.62 x 2 wasn't
enough for the mode it was trying to use, and so it ended up rejecting
the modeset, not because of an invalid cloning configuration, but
because of supposedly running out of FDI bandwidth. Took me a while
to figure out what had actually happened.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-12-git-send-email-ville.syrjala@linux.intel.com
With the output_types bitmask there's no need to loop through
the encoders anymore when checking for HDMI+non-HDMI cloning.
v2: Use output_types bitmask
v3: Fix the logic to really check that there are no non-HDMI encoders
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v2)
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-11-git-send-email-ville.syrjala@linux.intel.com
has_dsi_encoder was introduced to indicate that the pipe is driving
a DSI encoder. Now that we have the output_types bitmask that can
tell us the same thing, let's just kill has_dsi_encoder.
v2: Rebase, handle BXT DSI transcoder, rewrote commit message
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-10-git-send-email-ville.syrjala@linux.intel.com
INTEL_OUTPUT_DISPLAYPORT hsa been bugging me for a long time. It always
looks out of place besides INTEL_OUTPUT_EDP and INTEL_OUTPUT_DP_MST.
Let's just rename it to INTEL_OUTPUT_DP.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-9-git-send-email-ville.syrjala@linux.intel.com
A bunch of places still look for DP encoders manually. Just call
intel_crtc_has_dp_encoder(). Note that many of these places don't
look for EDP or DP_MST, but it's still fine to replace them because
* for audio we don't enable audio on eDP anyway
* the code that lack DP MST check is only for plaforms that
don't support MST anyway
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-8-git-send-email-ville.syrjala@linux.intel.com
With the introduction of the output_types mask, intel_pipe_has_type()
and intel_pipe_will_have_type() are basically the same thing. Replace
them with a new intel_crtc_has_type() (identical to
intel_pipe_will_have_type() actually).
v2: Rebase
v3: Make intel_crtc_has_type() static inline (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v2)
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-5-git-send-email-ville.syrjala@linux.intel.com
Rather than looping through encoders to see which encoder types
are being driven by the pipe, add an output_types bitmask into
the crtc state and populate it prior to compute_config and during
state readout.
v2: Determine output_types before .compute_config() hooks are called
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-4-git-send-email-ville.syrjala@linux.intel.com
If we've determined that the encoder is eDP, we shouldn't try to use MST
on it. Or at least the code doesn't seem to expect that since there are
some type==DP checks in the MST code.
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-2-git-send-email-ville.syrjala@linux.intel.com
Rather than using wait_for_atomic() when chacking for a response from
the GuC, we can get the effect of a hybrid spin/sleep wait by breaking
it into two stages. First, spin-wait for up to 10us to minimise latency
for "quick" commands; then, if that times out, sleep-wait for up 10ms
(the maximum allowed for a "slow" command).
Being able to do this depends on the recent patch
18f4b84 drm/i915: Use atomic waits for short non-atomic ones
and is similar to the hybrid approach in
1758b90 drm/i915: Use a hybrid scheme for fast register waits
(although we can't use that as-is, because that interface doesn't quite
match what we need here).
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467815411-21756-1-git-send-email-david.s.gordon@intel.com
As we inspect both the tasklet (to check for an active bottom-half) and
set the irq-posted flag at the same time (both in the interrupt handler
and then in the bottom-halt), group those two together into the same
cacheline. (Not having total control over placement of the struct means
we can't guarantee the cacheline boundary, we need to align the kmalloc
and then each struct, but the grouping should help.)
v2: Try a couple of different names for the state touched by the user
interrupt handler.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467805142-22219-3-git-send-email-chris@chris-wilson.co.uk
Following on from the scenario Tvrtko envisioned to explain a hard-to-hit
race with multiple first waiters, we could also then race in the
__i915_request_irq_complete() and the bottom-half may miss the vital
irq-seqno barrier and so go to sleep not noticing their seqno is
complete.
v2: unlock, not double lock the rcu_read_lock.
Fixes: 3d5564e910 ("drm/i915: Only apply one barrier after...")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467805142-22219-2-git-send-email-chris@chris-wilson.co.uk
After assigning ourselves as the new bottom-half, we must perform a
cursory check to prevent a missed interrupt. Either we miss the interrupt
whilst programming the hardware, or if there was a previous waiter (for
a later seqno) they may be woken instead of us (due to the inherent race
in the unlocked read of b->tasklet in the irq handler) and so we miss the
wake up.
Spotted-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96806
Fixes: 688e6c7258 ("drm/i915: Slaughter the thundering... herd")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467805142-22219-1-git-send-email-chris@chris-wilson.co.uk
The GPU init path now reports any errors which might occur more accurately
than what is possible with the generic "something failed" message.
Remove the generic reporting, so we don't log an error into dmesg anymore
if any of the GPU cores are ignored.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Print error messages that mention the exact cause of the failure on
all paths which may fail the GPU init.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Enable GPU module level hardware clock gating, using the conditions
found in the galcore v5 driver.
v2 lst: Split out clock gating enable into separate function, as
there might be more conditions needed for new hardware.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
The document about rockchip platform make a mistaken in available
compatible name of "rk3288-edp", we should correct it to "rk3288-dp"
which correspond to the compatible name in driver.
This mistaken was introduced in commit be91c36247 ("dt-bindings:
add document for rockchip variant of analogix_dp").
Reported-by: Tomasz Figa <tfiga@chromium.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
For RK3399's GRF module, if we want to operate the graphic related grf
registers, we need to enable the pclk_vio_grf which supply power for VIO
GRF IOs, so it's better to introduce an optional grf clock in driver.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
The enum value of DP_IRQ_TYPE_HP_CABLE_IN is zero, but driver only
send drm hp event when the irq_type and the enum value is true.
if (irq_type & DP_IRQ_TYPE_HP_CABLE_IN || ...)
drm_helper_hpd_irq_event(dp->drm_dev);
So there would no drm hpd event when cable plug in, to fix that
just need to assign all hotplug enum with no-zero values.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
The hardware IC designed that VOP must output the RGB10 video format to
eDP contoller, and if eDP panel only support RGB8, then eDP contoller
should cut down the video data, not via VOP contoller, that's why we need
to hardcode the VOP output mode to RGA10 here.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Rockchip VOP couldn't output YUV video format for eDP controller, so
when driver detect connector support YUV video format, we need to hack
it down to RGB888.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
It's better to pass the connector to platform driver in .get_modes()
callback, just like what the .get_modes() helper function designed.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Some boards don't need to declare a panel device node, like the
display interface is DP monitors, so it's necessary to make the
panel detect to an optional action.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
RK3399 and RK3288 shared the same eDP IP controller, only some light
difference with VOP configure and GRF configure.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Since drm_i915_private is now a subclass of drm_device we do not need to
chase the drm_i915_private->dev backpointer and can instead simply
access drm_i915_private->drm directly.
text data bss dec hex filename
1068757 4565 416 1073738 10624a drivers/gpu/drm/i915/i915.ko
1066949 4565 416 1071930 105b3a drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
struct drm_i915_private *d;
identifier i;
@@
(
- d->dev->i
+ d->drm.i
|
- d->dev
+ &d->drm
)
and for good measure the dev_priv->dev backpointer was removed entirely.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467711623-2905-4-git-send-email-chris@chris-wilson.co.uk
As we can just directly use drm_dev->drm.dev, we do not need the
drm_dev->dev backpointer anymore and can also loose the warning about
order of __i915_printk() and our initialisation (which is now always
safe).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467711623-2905-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
