Add a new read function to the at24 driver allowing to retrieve the
factory-programmed mac address embedded in chips from the at24mac
family.
These chips can be instantiated similarily to the at24cs family,
except that there's no way of having access to both the serial number
and the mac address at the same time - the user must instantiate
either an at24cs or at24mac device as both special memory areas are
accessible on the same slave address.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The chips from the at24cs family have two memory areas - a regular
read-write block and a read-only area containing the serial number.
The latter is visible on a different slave address (the address of the
rw memory block + 0x08). In order to access both blocks the user needs
to instantiate a regular at24c device for the rw block address and a
corresponding at24cs device on the serial number block address.
Add a function that allows to access the serial number and assign it
to at24->read_func if the chip allows serial number read operations
and the driver was passed the relevant flag for this device.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use BIT() macro to replace the 0xXX constants in platform_data flags
definitions.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Split at24_eeprom_write() into three smaller functions - one for the
i2c operations and two for the smbus extensions (separate routines for
block and byte transfers). Assign them in at24_probe() depending on
the bus capabilities.
Also: in order to avoid duplications move code adjusting the count
argument into a separate function and use it for i2c and smbus block
writes (no need for a roll-over for byte writes as we're always
writing one byte).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Split at24_eeprom_read() into two smaller functions - one for the
i2c operations and one for the smbus extensions. Assign them in
at24_probe() depending on the bus capabilities.
Also: in order to avoid duplications move the comments related to
offset calculations above the at24_translate_offset() routine.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Before splitting the read/write routines into smaller, more
specialized functions, unduplicate some code in advance.
Use a 'for' loop instead of 'do while' when waiting for the previous
write to complete and hide it behind a macro.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The first step in simplifying the read and write functions is to call
them via function pointers stored in at24_data. When we eventually
split the routines into smaller ones (depending on whether they use
smbus or i2c operations) we'll simply assign them to said pointers
instead of checking the flags at runtime every time we read/write.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Align the arguments in broken lines with the arguments list's opening
brackets and make checkpatch.pl happy by converting 'unsigned' into
'unsigned int'.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In preparation for splitting at24_eeprom_write() & at24_eeprom_read()
into smaller, specialized routines move at24_read() below, so that it
won't be intertwined with the low-level EEPROM accessors.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As part of the preparation for introducing support for more chips,
improve the readability of the device table by separating columns
with tabs.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This chapter is outdated. I almost removed, but, as we're lacking
documentation about how to make DVB devices persistent, I opted,
instead, to keep it, and add a note about that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are some things that needed to be done to convert
it to ReST. Also, there are some obsolete info there
related to Kernels 2.4 and 2.6. Update them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This file is shown OK with ReST. Yet, as we changed the
place where the get_dvb_firmware script is, we need to
update it.
While here, move the author's name to the beginning of the
file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This file was missing a name for the index, and weren't
using any markup language. Make it looks better and
convert to ReST.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The contributors list needs some adjustments to be properly
formatted.
Also, this list has not been updated for a while. So, add a
notice about that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The old ci.txt file had a very peculiar format, with doesn't
match any markup language I know. Change it to be on ReST
format, for it to be parsed by Sphinx.
Also, as this is an old document, add a note about it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This file is using a markup-like language, but it is not quite
ReST. Convert it, and add a note pointing to the Wiki page with
the known supported hardware devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This document almost follows a markup language, but it is
not ReST. Fix it to be handled by Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This file is almost at the ReST format, but some things need
to be fixed for it to be parsed.
Also, the documentation there is old. So, add a notice about
that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of keeping the introduction together with the
index, move it to a separate file, and add it via toctree
at the index.
The information there are outdated, so update it to point
to the right links.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several documentation stuff under Documentation/dvb.
Move them to Documentation/media/dvb-drivers and rename them to
rst, as they'll soon be converted to rst files.
No changes at the documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The conversion from DocBook required some fixes:
- Now, the C files with the exported symbols also need to be
added. So, all headers need to be included twice: one to
get the structs/enums/.. and another one for the functions;
- Notes should use the ReST tag, as kernel-doc doesn't
recognizes it anymore;
- Identation needs to be fixed, as ReST uses it to identify
when a format "tag" ends.
- Fix the cross-references at the media controller description.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There were lots of issues at the media controller side,
after the conversion:
- Some documentation at the header files weren't using the
kernel-doc start block;
- Now, the C files with the exported symbols also need to be
added. So, all headers need to be included twice: one to
get the structs/enums/.. and another one for the functions;
- Notes should use the ReST tag, as kernel-doc doesn't
recognizes it anymore;
- Identation needs to be fixed, as ReST uses it to identify
when a format "tag" ends.
- Fix the cross-references at the media controller description.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The conversion from DocBook lead into some conversion issues,
basically due to the lack of proper support at kernel-doc.
So, address them:
- Now, the C files with the exported symbols also need to be
added. So, all headers need to be included twice: one to
get the structs/enums/.. and another one for the functions;
- Notes should use the ReST tag, as kernel-doc doesn't
recognizes it anymore;
- Identation needs to be fixed, as ReST uses it to identify
when a format "tag" ends.
- kernel-doc doesn't escape things like *pointer, so we
need to manually add a escape char before it.
- On some cases, kernel-doc conversion requires violating
the 80-cols, as otherwise it won't properly parse the
source code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The kernel-doc script is now broken if it doesn't find all
exported symbols documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Just like the uAPI book is split into parts, let's split the
kAPI documentation. That should make easier to maintain, and
will split the final documentation into smaller html files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the contents of the media section at
DocBooks/DocBook/device-drivers.tmpl to a new ReST book.
For now, the contents is kept as-is. Next patches will fix
the warnings and add cross-references that were removed due to
the conversion.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The label lio_xmit_failed is used 3 times through liquidio_xmit() but it
always makes a call to dma_unmap_single() using potentially
uninitialized variables from "ndata" variable. Out of the 3 gotos, 2 run
after ndata has been initialized, and had a prior dma_map_single() call.
Fix this by adding a new error label: lio_xmit_dma_failed which does
this dma_unmap_single() and then processed with the lio_xmit_failed
fallthrough.
Fixes: f21fb3ed36 ("Add support of Cavium Liquidio ethernet adapters")
Reported-by: coverity (CID 1309740)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case nb8800_receive() fails to allocate a fragment, we would leak the
SKB freshly allocated and just return, instead, free it.
Reported-by: coverity (CID 1341750)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be using a logical check here instead of a bitwise operation
to check if the device is closed already in et131x_tx_timeout().
Reported-by: coverity (CID 146498)
Fixes: 38df6492eb ("et131x: Add PCIe gigabit ethernet driver et131x to drivers/net")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should have been obvious, only called from bpf() syscall via map_update_elem()
that calls bpf_fd_array_map_update_elem() under RCU read lock and thus this
must also be in GFP_ATOMIC, of course.
Fixes: 3b1efb196e ("bpf, maps: flush own entries on perf map release")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 90017accff ("sctp: Add GSO support") didn't register SCTP GSO
offloading for IPv6 and yet didn't put any restrictions on generating
GSO packets while in IPv6, which causes all IPv6 GSO'ed packets to be
silently dropped.
The fix is to properly register the offload this time.
Fixes: 90017accff ("sctp: Add GSO support")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d46e416c11 missed to update some other places which checked for
the socket being TCP-style AND Established state, as Closing state has
some overlapping with the previous understanding of Established.
Without this fix, one of the effects is that some already queued rx
messages may not be readable anymore depending on how the association
teared down, and sending may also not be possible if peer initiated the
shutdown.
Also merge two if() blocks into one condition on sctp_sendmsg().
Cc: Xin Long <lucien.xin@gmail.com>
Fixes: d46e416c11 ("sctp: sctp should change socket state when shutdown is received")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dongpo Li says:
====================
Add Hisilicon MDIO bus driver and FEMAC driver
This patch set adds a Hisilicon MDIO bus driver and
a Fast Ethernet MAC(FEMAC) driver.
We also abstract a general interface "of_phy_get_and_connect"
for PHY connect. User will have no bother with getting
"phy-mode" and "phy-handle" any more.
Changes in v1:
- Pass private data structure instead of struct mii_bus
in MDIO read and write operation.
- Return the error which devm_clk_get() gives when MDIO probe.
- Leave the clock unprepared and disabled on error when MDIO probe.
- Abstract a general interface "of_phy_get_and_connect" for PHY connect.
- Remove the "_reset" suffixes in "reset-names" property.
- Enable tx per-packet interrupt when tx fifo full.
- Remove pointless compatible and add SoC specific compatible.
- Declare only one clock in MAC dts documentation.
- Add standard unit suffixes for "phy-reset-delays".
- Use a smaller NAPI poll weight 16 for our Fast Ethernet MAC.
- Use phy_ethtool_{get|set}_link_ksettings for ethtool ops.
- Use phydev from struct net_device in MAC driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Hisilicon Fast Ethernet MAC(FEMAC) driver.
The FEMAC supports max speed 100Mbps and has been used in many
Hisilicon SoC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abstract a general interface "of_phy_get_and_connect"
for PHY connect. User will have no bother with getting
"phy-mode" and "phy-handle" any more.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a separate driver for the MDIO interface of the
Hisilicon Fast Ethernet MAC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI_CPSW_PHY_SEL depended on TI_CPSW and was selected by the latter. So
there is no reason to have this symbol visible.
A further optimisation would be to put the code for both symbols into a
single module which would allow to not export at least cpsw_phy_sel()
and simplify the module load process.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was used err_xxx for labeled statement, it is
not easy to understand, now use free_xxx for labeled
statement.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for hardware offloading of ipmr/ip6mr we need an
interface that allows to check (and later update) the age of entries.
Relying on stats alone can show activity but not actual age of the entry,
furthermore when there're tens of thousands of entries a lot of the
hardware implementations only support "hit" bits which are cleared on
read to denote that the entry was active and shouldn't be aged out,
these can then be naturally translated into age timestamp and will be
compatible with the software forwarding age. Using a lastuse entry doesn't
affect performance because the members in that cache line are written to
along with the age.
Since all new users are encouraged to use ipmr via netlink, this is
exported via the RTA_EXPIRES attribute.
Also do a minor local variable declaration style adjustment - arrange them
longest to shortest.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Shrijeet Mukherjee <shm@cumulusnetworks.com>
CC: Satish Ashok <sashok@cumulusnetworks.com>
CC: Donald Sharp <sharpd@cumulusnetworks.com>
CC: David S. Miller <davem@davemloft.net>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
macsec can't cope with mtu frames which need vlan tag insertion, and
vlan device set the default mtu equal to the underlying dev's one.
By default vlan over macsec devices use invalid mtu, dropping
all the large packets.
This patch adds a netif helper to check if an upper vlan device
needs mtu reduction. The helper is used during vlan devices
initialization to set a valid default and during mtu updating to
forbid invalid, too bit, mtu values.
The helper currently only check if the lower dev is a macsec device,
if we get more users, we need to update only the helper (possibly
reserving an additional IFF bit).
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices of the same type all export the same, random MAC address. This
behavior has been seen on the ZTE MF910, MF823 and MF831, and there are
probably more devices out there. Fix this by generating a valid random MAC
address if we read a random MAC from device.
Also, changed the memcpy() to ether_addr_copy(), as pointed out by
checkpatch.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
