Both ext3 and ext4 put the half-created symlink inode into the orphan list
for a while (see the comment in ext[34]_symlink() for gory details). Then,
if everything went fine, they pull it out of the orphan list and bump the
link count back to 1. The thing is, inc_nlink() is going to complain about
seeing somebody changing i_nlink from 0 to 1. With a good reason, since
normally something like that is a bug. Explicit set_nlink(inode, 1) does
the same thing as inc_nlink() here, but it does *not* complain - exactly
because it should be usable in strange situations like this one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
We have already set ->s_root, so ->put_super() is going to be called.
Freeing ->s_fs_info is a bloody bad idea when it's going to be
dereferenced very shortly...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
devpts_kill_sb() is called even if devpts_fill_super() fails;
we should not do that kfree() in the latter, especially not
with ->s_fs_info left pointing to freed object. Double kfree()
is a Bad Thing(tm)...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add SCIF2 and SCIF4 pin configuration code to
the r8a7779 Marzen board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add GPIO-only r8a7779 PFC support V2.
Only regular GPIOs are supported at this time. GPIO_FN are not
supported because they require variable bit width support in be
the shared pfc code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* if you do dput() of root dentry, do *not* follow that with iput() of root
inode.
* while we are at it, don't do that dput() at all - you are leaving the pointer
in ->s_root and your ->kill_sb() will be very unhappy with that. It will do
proper dput(), though, so the easiest way is to leave that to it entirely.
* freeing ->s_fs_info is also best left to ->kill_sb() (which will do it
anyway), especially since we leave the pointer in place.
* that xchg() in ->kill_sb() is not a bug per se, but it's a plain and simple
masturbation with fewer excuses than Onan had...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Initial support for the r8a7779 SoC and the Marzen board (V2).
Only SCIF ports and the TMU are supported at this point.
To keep things simple only entity-mapped virt-to-phys mappings
are supported. This forces drivers and other SoC glue code to
make use of ioremap(). We cannot support early serial console
due to virtual address space collisions with the ARM kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add PFC support for a 32-bit unlock register. Needed to
drive the r8a7779 PFC that comes with a funky PMMR register.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for variable config reg hardware by adding
the macro PINMUX_CFG_REG_VAR(). The width of each bitfield
needs to be passed to the macro, and the correct space must
be consumed by each bitfield in the enum table following the
macro. Data registers still need to have fixed bitfields.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a helper function for shared config reg access
calculations. This allows us to reduce the amount
of duplicated code, and at the same time prepare
for a common place for future variable bitwidth
config reg support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the way the PFC code is passing bitfield
selection between configure register functions.
Convert the code from using index only to bitfield
number and selected value. First step towards future
variable bitfield width support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Introduce gpio_read_bit() for data register read access
and modify sh_gpio_get_value() to make use of the new
function instead of gpio_read_reg(). The purpose of
this change is to update the code to only use the
gpio_read_reg() function for config register access.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The AHCI controller found in the STA2X11 chip uses BAR number 0
instead of 5. Also, the chip's fixup code sets a special DMA mask
for all of its PCI functions, and the mask must be preserved here.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The author of this driver clearly wasn't familiar with the BMIDE specification
(also known as SFF-8038i) when he implemented the bmdma_status() method: first,
the interrupt bit of the BMIDE status register corresponds to nothing else but
INTRQ signal (ATAPI_DEV_INT here); second, the error bit is only set if the
controller encounters issue doing the bus master transfers, not on the IDE DMA
burst termination interrupts like here (moreover, setting the error bit doesn't
cause an interrupt). We now need to disable all those unused interrupts...
(The only thing I couldn't figure out is how to flush the FIFO to memory once
the interrupt happens as required by the mentioned spec.)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ata port is brought back to full power state during system resume.
So its runtime PM status will have to be updated to reflect
the actual post-system sleep status.
This also fixes below warning during system suspend/resume.
WARNING: at /work/linux/drivers/ata/libata-eh.c:4034
ata_scsi_port_error_handler+0x89/0x557()
4034 WARN_ON(!(ap->pflags & ATA_PFLAG_SUSPENDED));
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[Patch description from Alan Stern]
If a child device was runtime-suspended when a system suspend began,
then there will be nothing to prevent its parent from
runtime-suspending as soon as it is woken up during the system resume.
Then when the time comes to resume the child, the resume will fail
because the parent is already back at low power.
On the other hand, there are some devices which should remain at low
power across an entire suspend-resume cycle. The details depend on the
device and the platform.
This suggests that the PM core is not the right place to solve the
problem. One possible solution is for the subsystem or device driver
to call pm_runtime_get_sync(dev->parent) at the start of the
system-resume procedure and pm_runtime_put_sync(dev->parent) at the
end.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add platform hooks for custom suspend() and resume() functions. The
generic suspend/resume code in drivers/ata/ahci_platform.c is adapted
from the PCI version in drivers/ata/ahci.c.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit b3a706014e (libata: Add a
drivers/ide style DMA disable) neglected to remove the line in
ata_do_set_mode() it has obviously made useless/duplicated. Do this
now, and make a line added back then wrapped properly...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
CONFIG_OF_IRQ is not available on some platforms and using of_irq_*
breaks the build. Since resources are already populated in the platform
device, get the irq from there instead.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch converts the drivers in drivers/ata/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sylvain Munaut <tnt@246tNt.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Mark Miesfeld <mmiesfeld@amcc.com>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Fix cable detection to also account for the slave device cable bit.
* Disable UDMA when programming MWDMA in cs5536_set_dmamode().
* Don't change UDMA settings in cs5536_set_piomode().
* Add cs5536_program_dtc() helper.
* Cleanup and uninline cs5536_[read,write]() methods.
Cc: Martin K. Petersen <mkp@mkp.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
atapi_pio_bytes() uses bare numbers for the ATAPI interrupt reason bits despite
these are #define'd in <linux/ata.h>.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ata port runtime suspend/resume/idle callbacks.
Set ->eh_noresume to skip the runtime PM calls on scsi host
in the error handler to avoid dead lock.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change ata_host_request_pm to ata_port_request_pm which performs
port suspend/resume.
Add ata port type driver which implements port PM callbacks.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sd_shutdown is called during reboot/poweroff.
It may fail if parent device, for example, ata port, was runtime suspended.
Fix it by checking runtime PM status of sd.
Exit immediately if sd was runtime suspended already.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The only high-level SCSI driver that currently implements runtime PM is
sd, and sd treats runtime suspend exactly the same as the SUSPEND and
HIBERNATE stages of system sleep, but not the same as the FREEZE stage.
Therefore, when entering the SUSPEND or HIBERNATE stages of system
sleep, we can skip the callback to the driver if the device is already
in runtime suspend. When entering the FREEZE stage, however, we should
first issue a runtime resume. The overhead of doing this is
negligible, because a suspended drive would be spun up during the THAW
stage of hibernation anyway.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With previous change, now the ata port runtime suspend will happen as:
disk suspend --> scsi target suspend --> scsi host suspend --> ata port
suspend
ata port(parent device) suspend need to schedule scsi EH which will resume
scsi host(child device). Then the child device resume will in turn make
parent device resume first. This is kind of recursive.
This patch adds a new flag Scsi_Host::eh_noresume.
ata port will set this flag to skip the runtime PM calls on scsi host.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, the device tree of ata port and scsi host looks as below,
/sys/devices/pci0000:00/0000:00:1f.2 (ahci controller)
|-- ata1 (ata port)
|-- host0 (scsi host)
|-- target0:0:0 (scsi target)
|-- 0:0:0:0 (disk)
This patch makes ata port as parent device of scsi host, then it becomes
/sys/devices/pci0000:00/0000:00:1f.2 (ahci controller)
|-- ata1 (ata port)
|-- host0 (scsi host)
|-- target0:0:0 (scsi target)
|-- 0:0:0:0 (disk)
With this change, the ata port runtime PM is easier.
For example, the ata port runtime suspend will happen as,
disk suspend --> scsi target suspend --> scsi host suspend --> ata port
suspend.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is another attempt at fixing the same problem that 270dac35c2
(libata: ahci_start_engine compliant to AHCI spec) tried to solve.
Unfortunately, 270dac35c2 created regressions for a lot more common
controllers and got reverted.
This specific AHCI IP block becomes a brick if the DMA engine is
started while DRQ is set. It is not possible to avoid the condition
completely but the most common occurrence is caused by spurious use of
ahci_start_engine() from ahci_start_port() during init sequence.
DMA engine is started after both soft and hard resets and
ahci_start_port() is always followed by resets, so there is no reason
to start DMA engine from ahci_start_port().
This patch removes ahci_start_engine() invocation from
ahci_start_port(). This change makes failure path of
ahci_port_suspend() leave engine stopped without following resets.
This is resolved by replacing ahci_start_port() call with
ata_port_freeze() which forces resets afterwards, which is the better
behavior anyway.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Jian Peng <jipeng2005@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The I2C suspend and resume functions have been deprecated since the driver
was introduced.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is possible that we will see another interrupt triggering at the same
time as the touchscreen interrupts so it's still worth checking other
possible sources. Almost all of the win from the fast path comes from only
needing to read the primary register and saving the I/O costs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Error handling code following a kzalloc should free the allocated data. At
this point, chip has been allocated and some fields have been initialized,
but it has not been stored anywhere, so it should be freed before leaving
the function.
A simplified version of the semantic match that finds the problem is as
follows: (http://coccinelle.lip6.fr)
// <smpl>
@r exists@
local idexpression x;
statement S;
identifier f1;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
x->f1
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch add Samsung S5M Kconfig and Makefile entry.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch support irq for s5m series.
Basically, S5M8767 and S5M8763 irq can be handled by this patch.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
S5M series are pmic including mutiple functional devices.
It can support PMIC, RTC, Battery charger, codec.
This patch implement core driver for s5m series.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It improves mc13xxx dt binding document on how the regulator name
is being used for binding a mc13892 regulator device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes:
WARNING: drivers/built-in.o(.text+0xf368f): Section mismatch in reference from
the function stmpe_probe() to the function .devinit.text:stmpe_chip_init()
The function stmpe_probe() references the function __devinit stmpe_chip_init().
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes:
drivers/mfd/stmpe.c:114:1: warning: data definition has no type or storage
class [enabled by default]
drivers/mfd/stmpe.c:114:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Wimplicit-int]
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
STMPE i2c is a bool and should depend on I2c=y.
That fixes:
drivers/built-in.o: In function `i2c_block_write':
stmpe-i2c.c:(.text+0xf4553): undefined reference to
+`i2c_smbus_write_i2c_block_data'
drivers/built-in.o: In function `i2c_block_read':
stmpe-i2c.c:(.text+0xf457f): undefined reference to
+`i2c_smbus_read_i2c_block_data'
drivers/built-in.o: In function `i2c_reg_write':
stmpe-i2c.c:(.text+0xf45ab): undefined reference to
`i2c_smbus_write_byte_data'
drivers/built-in.o: In function `i2c_reg_read':
stmpe-i2c.c:(.text+0xf45d4): undefined reference to `i2c_smbus_read_byte_data'
drivers/built-in.o: In function `stmpe_init':
stmpe-i2c.c:(.init.text+0xaf22): undefined reference to `i2c_register_driver'
drivers/built-in.o: In function `stmpe_exit':
stmpe-i2c.c:(.exit.text+0x5e5): undefined reference to `i2c_del_driver'
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
