TX_ENDIAN/RX_ENDIAN bits define whether to reverse the endian
order of the data DMA from/to memory. The endian order should
keep the same with cpu endian.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TI QSPI has four 32 bit data regsiters which can be used to transfer 16
bytes of data at once. The register group QSPI_SPI_DATA_REG_3,
QSPI_SPI_DATA_REG_2, QSPI_SPI_DATA_REG_1 and QSPI_SPI_DATA_REG is
treated as a single 128-bit word for shifting data in and out. The bit
at QSPI_SPI_DATA_REG_3[31] position is the first bit to be shifted out
in case of 128 bit transfer mode. Therefore the first byte to be written
to flash should be at QSPI_SPI_DATA_REG_3[31-25] position.
Instead of writing 1 byte at a time when interacting with spi-nor flash,
make use of all the four registers so that 16 bytes can be transferred
in one go. This reduces number of register writes and Word Complete
interrupts for a given transfer message size, thereby increasing the
write performance.
Without this patch the raw flash write speed is ~100KB/s, with this
patch the write speed increases to ~400 kB/s on DRA74 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_parse_phandle() returns a device_node pointer with the refcount
incremented. We should dispose of this reference when we're finished.
Drop the reference acquired by of_parse_phandle().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The pcibios_msi_controller() hook was only implemented by ARM, and it sets
pci_bus->msi now, so it doesn't need this hook anymore.
Remove the unused pcibios_msi_controller() hook.
[bhelgaas: changelog, split into separate patch]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ARM now uses pci_bus->msi to store the msi_controller pointer, so we don't
need to save it in struct pci_sys_data, and we don't need to implement
pcibios_msi_controller() to get it out of pci_sys_data.
Remove msi_controller from struct pci_sys_data and
pcibios_msi_controller().
[bhelgaas: changelog, split into separate patch]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
ARM previously stored the msi_controller pointer in its sysdata, struct
pci_sys_data, and implemented pcibios_msi_controller() to retrieve it.
That made PCI host controller drivers specific to ARM because they had to
put the msi_controller pointer in the ARM-specific pci_sys_data.
There is now a generic mechanism, pci_scan_root_bus_msi(), for giving the
msi_controller pointer to the PCI core. Use this for all ARM systems and
for the DesignWare and Xilinx PCI host controller drivers.
This removes an ARM dependency from the DesignWare, DRA7xx, EXYNOS, i.MX6,
Keystone, Layerscape, SPEAr13xx, and Xilinx drivers.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Simon Horman <horms@verge.net.au>
CC: Russell King <linux@arm.linux.org.uk>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
Add a pci_scan_root_bus_msi() interface so an arch can specify the MSI
controller up front. This removes the need for a pcibios callback to set
the MSI controller later.
This is not exported because I'd like to replace the variety of "scan root
bus" interfaces with a single, more extensible interface that can handle
the MSI controller, domain, pci_ops, resources, etc. I hope this interface
is temporary.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
In the ARM PCI bios32 layer, failures to dynamically allocate pci_sys_data
for a PCI bus, or a PCI bus scan failure have to be considered serious
warnings but they should not trigger a system panic so that at least the
system is given a chance to be debugged.
This patch replaces the panic statements with WARN() messages to improve
error reporting in the ARM PCI bios32 layer.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Marc Zyngier <marc.zyngier@arm.com>
Make pci-host-generic driver (kernel option PCI_HOST_GENERIC) available on
arm64.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ARM64 requires setup-irq.o to provide pci_fixup_irqs() implementation. We
are adding this now to support the pci-host-generic host controller, but we
enable it for ARM64 PCI so that other host controllers can use this as
well.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The generic OF-based host controller driver uses pci_common_init_dev(),
which is ARM-specific and requires the ARM struct hw_pci. The part of
pci_common_init_dev() that is needed is limited and can be done here
without using hw_pci.
Note that the ARM pcibios functions expect the PCI sysdata to be a pointer
to a struct pci_sys_data. Add a struct pci_sys_data as the first element
in struct gen_pci so that when we use a gen_pci pointer as sysdata, it is
also a pointer to a struct pci_sys_data.
Create and scan the root bus directly without using the ARM
pci_common_init_dev() interface.
[bhelgaas: changelog, move pcie_bus_configure_settings() before
pci_bus_add_devices(), combine !PCI_PROBE_ONLY blocks]
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Current sed script makes assumptions about the structure of rules that
group .text sections in the vmlinux linker script. These assumptions
get broken occasionally, e.g.: 779c88c94c "ARM: 8321/1: asm-generic:
introduce.text.fixup input section", or 9bebe9e5b0 "kbuild: Fix
.text.unlikely placement".
Rewrite sed rules so that they don't depend on number/arrangement of text
sections in *(...) blocks.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Commit 6dd747825b ("ARM: imx: move timer resources into a structure")
moved initialization parameters into a data structure, but neglected to set
the irq field in that data structure for non-DT boots. This causes the system
to hang if a non-DT boot is attempted.
Fixes: 6dd747825b ("ARM: imx: move timer resources into a structure")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1440066441-13930-1-git-send-email-linux@roeck-us.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since commit feb44f1f7a (x86/xen:
Provide a "Xen PV" APIC driver to support >255 VCPUs) Xen guests need
a full APIC driver and thus should depend on X86_LOCAL_APIC.
This fixes an i386 build failure with !SMP && !CONFIG_X86_UP_APIC by
disabling Xen support in this configuration.
Users needing Xen support in a non-SMP i386 kernel will need to enable
CONFIG_X86_UP_APIC.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: <stable@vger.kernel.org>
User visible:
- Fix buildid processing done at the end of a 'perf record' session, a
problem that happened in workloads involving lots of small short-lived
processes. That code was not asking the perf_session layer to order
the events.
Make the code more robust to handle some of the problems with such
out-of-order events and fix 'perf record' to ask for ordered events
on systems where we have perf_event_attr.sample_id_all. (Adrian Hunter)
- Show backtrace when handling a SIGSEGV in 'perf top --stdio' (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5Zmg
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Fix buildid processing done at the end of a 'perf record' session, a
problem that happened in workloads involving lots of small short-lived
processes. That code was not asking the perf_session layer to order
the events.
Make the code more robust to handle some of the problems with such
out-of-order events and fix 'perf record' to ask for ordered events
on systems where we have perf_event_attr.sample_id_all. (Adrian Hunter)
- Show backtrace when handling a SIGSEGV in 'perf top --stdio' (Arnaldo Carvalho de Melo)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Simplify a trivial if-return sequence by combining it with a preceding
function call.
The semantic patch that makes this change is available in
scripts/coccinelle/misc/simple_return.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lucas Stach <l.stach@pengutronix.de>
Use BUG_ON() instead of an if condition followed by BUG().
The semantic patch that makes this change is available in
scripts/coccinelle/misc/bugon.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
There is no need to use the IS_ERR_VALUE() macro for checking the return
value from pm_runtime_* functions.
Test for a negative pm_runtime_get_sync() return value instead of using
IS_ERR_VALUE().
The semantic patch that makes this change is available in
scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
Add a function to find the start of the SADs in the ELD. This
complements the helper to retrieve the SAD count.
[airlied: this fixes a build problem with the alsa eld helper
which required this].
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The TI crossbar irqchip doesn't provides any facility to configure the
wakeup sources, but the conversion to hierarchical irqdomains set the
irq_set_wake callback to irq_chip_set_wake_parent. The parent chip
(OMAP wakeupgen) has no irq_set_wake function either so the call will
fail with -ENOSYS. As a result the irq_set_wake() call in the resume
path will trigger an 'Unbalanced wake disable' warning.
Before the conversion the GIC irqchip was the top level irqchip and
correctly flagged with IRQCHIP_SKIP_SET_WAKE.
Restore the correct behaviour by removing the irq_set_type callback
from the crossbar irqchip and set the IRQCHIP_SKIP_SET_WAKE flag which
lets the irq_set_irq_wake() call from the driver succeed.
[ tglx: Massaged changelog ]
Fixes: 783d31863f ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-7-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ARM GIC requires that all interrupts which are not used as a
wakeup source have to be masked during suspend.
The conversion of the crossbar irqchip to hierarchical irq domains
failed to mark the crossbar irqchip with the IRQCHIP_MASK_ON_SUSPEND
flag and therefor broke the suspend requirement of the GIC.
Before the conversion the flags were visible because the GIC was the
top level irqchip. After the conversion the crossbar irqchip is the
top level irq chip whose flags are evaluated in suspend_device_irq().
As the flag is not set the masking of the non-wakeup irqs is not
invoked which breaks suspend.
Add the IRQCHIP_MASK_ON_SUSPEND flag to the crossbar irqchip, so the
GIC interrupts get masked properly.
[ tglx: Massaged changelog ]
Fixes: 783d31863f ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-6-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The conversion of the wakeupgen irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.
The wakeupgen irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.
Restore the correct behaviour by setting the wakeupgen irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.
[ tglx: Massaged changelog ]
Fixes: 7136d457f3 ('ARM: omap: convert wakeupgen to stacked domains')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-5-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The conversion of the crossbar irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.
The crossbar irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.
Restore the correct behaviour by setting the crossbar irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.
[ tglx: Massaged changelog ]
Fixes: 783d31863f ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-4-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This helper is required for irq chips which do not implement a
irq_set_type callback and need to call down the irq domain hierarchy
for the actual trigger type change.
This helper is required to fix further wreckage caused by the
conversion of TI OMAP to hierarchical irq domains and therefor tagged
for stable.
[ tglx: Massaged changelog ]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-3-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_chip_retrigger_hierarchy() returns -ENOSYS if it was not able to
find at least one .irq_retrigger() callback implemented in the IRQ
domain hierarchy.
That's wrong, because check_irq_resend() expects a 0 return value from
the callback in case that the hardware assisted resend was not
possible. If the return value is non zero the core code assumes
hardware resend success and the software resend is not invoked.
This results in lost interrupts on platforms where none of the parent
irq chips in the hierarchy implements the retrigger callback.
This is observable on TI OMAP, where the hierarchy is:
ARM GIC <- OMAP wakeupgen <- TI Crossbar
Return 0 instead so the software resend mechanism gets invoked.
[ tglx: Massaged changelog ]
Fixes: 85f08c17de ('genirq: Introduce helper functions...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-2-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We should not assume any particular hardware topology. Commit d0751b98df
("PCI: Add dev->has_secondary_link to track downstream PCIe links") relied
on the assumption that every PCIe hierarchy is rooted at a Root Port. But
we can't rely on any assumption about what hardware we will find; we just
have to deal with the world as it is.
On some platforms, PCIe devices (endpoints, switch upstream ports, etc.)
appear directly on the root bus, and there is no Root Port in the PCI bus
hierarchy. For example, Meelis observed these top-level devices on a
Sparc V245:
0000:02:00.0 PCI bridge to [bus 03-0d] Switch Upstream Port
0001:02:00.0 PCI bridge to [bus 03] PCIe to PCI/PCI-X Bridge
These devices *look* like they have links going upstream, but there really
are no upstream devices.
In set_pcie_port_type(), we used the parent device to figure out which side
of a switch port has a link, so if the parent device did not exist, we
dereferenced a NULL parent pointer.
Check whether the parent device exists before dereferencing it.
Meelis observed this oops on Sparc V245 and T2000. Ben Herrenschmidt says
this is also possible on IBM PowerVM guests on PowerPC.
[bhelgaas: changelog, comment]
Link: http://lkml.kernel.org/r/alpine.LRH.2.20.1508122118210.18637@math.ut.ee
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
It was just freezing instead of informing about the SEGV, fix it and
also print a backtrace, just like in the TUI mode and in 'perf trace'.
Tested by provoking a NULL deref when pressing 'z':
0.31% libc-2.20.so [.] malloc_consolidate
0.31% ld-2.20.so [.] _dl_relocate_object
0.28% cc1 [.] ht_lookup
0.28% cc1 [.] ira_init_register_move_cost
perf: Segmentation fault
Obtained 7 stack frames.
perf(dump_stack+0x32) [0x4d69f2]
perf(sighandler_dump_stack+0x29) [0x4d6a89]
/lib64/libc.so.6(+0x34960) [0x7f5064333960]
perf() [0x438790]
/lib64/libpthread.so.0(+0x752a) [0x7f50663dd52a]
/lib64/libc.so.6(clone+0x6d) [0x7f50643ff22d]
#
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-pewrpzqd29rgmhu2wkk7fhww@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
clock in prepare_hardware/unprepare_hardware is redundant
with pm_runtime, so remove them.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After recording, 'perf record' post-processes the data to determine
which buildids are needed.
That processing must process the data in time order, if possible,
because otherwise dependent events, like forks and mmaps, will not make
sense.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1439994561-27436-4-git-send-email-adrian.hunter@intel.com
[ Moved the sample_id_add to after trying to open the events, use pr_warning ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When processing a fork event, the tools lookup the parent thread by its
tid. In a couple of cases, it is possible for that thread to have the
wrong pid.
That can happen if the data is being processed out of order, or if the
(fork) event that would have removed the erroneous thread was lost.
Assume the latter case, print a dump message, remove the erroneous
thread, create a new one with the correct pid, and keep going.
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1439994561-27436-3-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Attempting to clone map groups onto themselves will deadlock.
It only happens because of other bugs, but the code should protect
itself anyway.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1439994561-27436-2-git-send-email-adrian.hunter@intel.com
[ Use pr_debug() instead of dump_fprintf() ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The topology code merged in the v4.2 merge window introduced a new ABI
which was believed to be suitable for use but subsequently additional
work by the developers of this feature have revealed some problems that
need to be addressed. In order to allow this to be done without having
to support the initial ABI add Kconfig to disable the build and also add
some #error statements to the UAPI header so users can't use them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV1K6xAAoJECTWi3JdVIfQl60H/Aiq3smUvb+npgLI402pdzZ8
eaGVSw1oGO7NFylBDu8FeiJLBvl4ZQmSfMbaLBJ50JPKqY1nFjOXFk0nWatQ8TPY
0aB1NKCIGNNCWXTO3ABZ8zeT5AH218n3t8tTUxWzOS1RhpZMwePVuS83+cdwfxAZ
He29rX2xfKFaGo92NMB707vU6aobYC0jc4pIaVoYLN7E49leTSzgGKKNVW2JyEog
d44Zd7jEXPY1lj166sEEF4axAzGc2ZkwsbmOmymbszEBkYtDVs1Q1omFf+CNi31Y
16bLwOVzTXVM7PeheRF2Tp6qtcyDpQhLicfBjakkJ1X5MtW3OzoutGli/isIh2g=
=Gj9l
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2-disable-topology' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Disable topology support for v4.2
The topology code merged in the v4.2 merge window introduced a new ABI
which was believed to be suitable for use but subsequently additional
work by the developers of this feature have revealed some problems that
need to be addressed. In order to allow this to be done without having
to support the initial ABI add Kconfig to disable the build and also add
some #error statements to the UAPI header so users can't use them.
Just setting fixed_uV is not enough, the regulator core will also check
n_voltages setting. The fixed_uV only works when n_voltages is 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of the LTC chips supported by this driver have to be polled
to ensure that they are ready to accept commands.
Signed-off-by: Michael Jones <mike@proclivis.com>
[Guenter Roeck: simplifications and formatting changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PMBus controllers optionally support PEC. Configure the driver
to use it if available to improve operational security.
Suggested-by: Michael Jones <mike@proclivis.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CMAC is an approved cipher in FIPS 140-2. The patch allows the use
of CMAC with TDES and AES in FIPS mode.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch moves the data allocated using dma_alloc_coherent to the
corresponding managed interface. To be compatible with the change,
various gotos are replaced with direct returns and unneeded labels
are dropped.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The fix for deadlock in PM in commit [1ee23fe07e: ALSA: usb-audio:
Fix deadlocks at resuming] introduced a new check of in_pm flag.
However, the brainless patch author evaluated it in a wrong way
(logical AND instead of logical OR), thus usb_autopm_get_interface()
is wrongly called at probing, leading to unbalance of runtime PM
refcount.
This patch fixes it by correcting the logic.
Reported-by: Hans Yang <hansy@nvidia.com>
Fixes: 1ee23fe07e ('ALSA: usb-audio: Fix deadlocks at resuming')
Cc: <stable@vger.kernel.org> [v3.15+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current code assigns 0 to variable 'err', which makes mantis_dma_init()
to return success even if mantis_alloc_buffers() fails.
Fix it by checking the return value from mantis_alloc_buffers() and
propagating it in the case of error.
Reported-by: RUC_Soft_Sec <zy900702@163.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 9869da5bac.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 1d971d927e.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit a0466f15b4.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit cf257e288a.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 0d830b2d12.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 2e4ebde269.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
