Debugging a report of a problem with an ancient solid state disk showed
up some problems in the IORDY handling
1. We check the wrong bit to see if the device has IORDY
2. Even then some ancient creaking piles of crap don't support
SETXFER at all.
The cases it fixes are obscure and the risk of side effects is slight
but possible. This also moves us slightly closer to supporting original
MFM/RLL disks with libata.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update hotplug to handle PMP links. When PMP is attached, the PMP
number corresponds to C of SCSI H:C:I:L. While at it, change argument
to ata_find_dev() to @devno from @id to avoid confusion with SCSI
device ID.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update ata_eh_autopsy(), ata_eh_report(),
ata_eh_revalidate_and_attach() and ata_eh_recover() to deal with PMP
links. ata_eh_autopsy() and ata_eh_report() updates are
straightforward. They just repeat the same operation over all
configured links. The only change to ata_eh_revalidate_and_attach()
is avoiding calling ->cable_select() on non-host ports.
ata_eh_recover() update is more complex as it first processes all
resets and then performs the rest. This is necessary as thawing with
some links in unknown state can be dangerous. ehi->action is cleared
on successful recovery of a link to avoid repeating recovery due to
failures in other links.
ata_eh_recover() iterates over only PMP links if PMP is attached, and,
on failure, the failing link is returned in @failed_link instead of
disabling devices directly. These are to integrate ata_eh_recover()
into PMP EH later.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update ata_scsi_error() to handle PMP links. As error conditions can
occur on both host and PMP links, __ata_port_for_each_link() is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add link->pmp, ap->nr_pmp_links, ap->pmp_link[], and implement/update
link helpers.
printk helpers are updated such that port and link are identifed as
'ataP:' if no PMP is attached, while device is identified as
'ataP.DD:'. If PMP is attached, they become 'ataP:', 'ataP.LL:' and
'ataP.LL' - ie. link and device are identified their PMP number.
If PPM is attached (ap->nr_pmp_links != 0), ata_for_each_link()
iterates over PMP links, while __ata_for_each_link() iterates over the
host link + PMP links. If PMP is not attached (ap->nr_pmp_links ==
0), both iterate over only the host link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out link initialization into ata_link_init() and
ata_link_init_sata_spd().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes. Move them to
ata_link->flags. This will allow host and PMP links to have different
attributes. ata_port_info->link_flags is added and used by LLDs to
specify these flags during initialization.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following functions deal with ata_link instead of ata_port.
* ata_set_mode()
* ata_eh_autopsy() and related functions
* ata_eh_report() and related functions
* suspend/resume related functions
* ata_eh_recover() and related functions
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_eh_about_to_do() and ata_eh_done() deal with ata_link instead
of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following PHY-related functions to deal with ata_link instead
of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Multiple links and different number of devices per link should be
considered to iterate over links and devices. This patch implements
and uses link and device iterators - ata_port_for_each_link() and
ata_link_for_each_dev() - and ata_link_max_devices().
This change makes a lot of functions iterate over only possible
devices instead of from dev 0 to dev ATA_MAX_DEVICES. All such
changes have been examined and nothing should be broken.
While at it, add a separating comment before device helpers to
distinguish them better from link helpers and others.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Remove in-source changelog. It's archived permanently in git and
various kernel archives, and changelogs should exist purely in git.
* Remove 2.4.x kernel support. It is an active obstacle to
modernizing this driver, at this point. This includes killing
gdth_kcompat.h which is 100% redundant in modern kernels.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Split out per-device pci probing and put it under proper CONFIG_PCI.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Split eisa probing into it's own helper, and do proper error unwinding.
Protect EISA probind by the proper CONFIG_EISA symbol.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
(note: this is ontop of Jeff's pci cleanup patch)
Split out isa probing into a helper of it's own. Error handling is
cleaned up, but errors are not propagated yet. Also enclose the isa
probe under the proper CONFIG_ISA symbol instead of the !IA64 hack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rather than having internal commands abuse scsi_done to call
gdth_scsi_done, have all the places that use to call scsi_done directly
call gdth_scsi_done, which now checks whether the command was internal,
and calls scsi_done if not.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Use new scsi_eh_prep/restor_cmnd() for synchronous
REQUEST_SENSE invocation.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Use new scsi_eh_prep/restor_cmnd() for synchronous
REQUEST_SENSE invocation.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Drivers/transports that want to send a synchronous REQUEST_SENSE command
as part of their .queuecommand sequence, have 2 new API's that facilitate
in doing so and abstract them from scsi-ml internals.
void scsi_eh_prep_cmnd(struct scsi_cmnd *scmd,
struct scsi_eh_save *sesci, unsigned char *cmnd,
int cmnd_size, int sense_bytes)
Will hijack a command and prepare it for request sense if needed.
And will save any later needed info into a scsi_eh_save structure.
void scsi_eh_restore_cmnd(struct scsi_cmnd* scmd,
struct scsi_eh_save *sesci);
Will undo any changes done to a command by above function. Making
it ready for completion.
- Re-factor scsi_send_eh_cmnd() to use above APIs
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- regrouped variables for easier reviewing of next patch
- Support of cmnd==NULL in call to scsi_send_eh_cmnd()
- In the @sense_bytes case set transfer size to the minimum
size of sense_buffer and passed @sense_bytes. cmnd[4] is
set accordingly.
- REQUEST_SENSE is set into cmnd[0] so if @sense_bytes is
not Zero passed @cmnd should be NULL.
- Also save/restore resid of failed command.
- Adjust caller
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I get this warnings on current git when CONFIG_PCI is not set :
drivers/scsi/fdomain.c:390: warning: 'PCI_dev' defined but not used
drivers/scsi/fdomain.c:1768: warning: 'fdomain_pci_tbl' defined but not used
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix section mismatch in the Adaptec DPT SCSI Raid driver.
WARNING: vmlinux.o(.init.text+0x1fcd2): Section mismatch:
reference to .exit.text:adpt_exit (between 'adpt_init' and 'ahc_linux_init')
This warning is due to adaptec device detection calling the exit routine on
failure to properly register the adaptec device.
The exit routine + call was added on July 30 by
Commit: 55d9fcf57b
Author: Matthew Wilcox
Subject: [SCSI] dpt_i2o: convert to SCSI hotplug model.
Mathew: isn't a module exit routine a little too strong to be calling on the
failure of a single device? Module exit implies that other, non-failing
adaptec raid devices will also get shut down.
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Modify ocfs2_dir_foreach_blk() to optionally return any error from the
filldir callback. This way ocfs2_dirforeach() can terminate early, as
opposed to always passing through the entire directory. This fixes a bug
introduced during a previous code refactor where ocfs2_empty_dir() would
loop infinitely.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Create all new directories with OCFS2_INLINE_DATA_FL and the inline data
bytes formatted as an empty directory. Inode size field reflects the actual
amount of inline data available, which makes searching for dirent space
very similar to the regular directory search.
Inline-data directories are automatically pushed out to extents on any
insert request which is too large for the available space.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
This splits out extent based directory read support and implements
inline-data versions of those functions. All knowledge of inline-data versus
extent based directories is internalized. For lookups the code uses
ocfs2_find_entry_id(), full dir iterations make use of
ocfs2_dir_foreach_blk_id().
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
This fixes up write, truncate, mmap, and RESVSP/UNRESVP to understand inline
inode data.
For the most part, the changes to the core write code can be relied on to do
the heavy lifting. Any code calling ocfs2_write_begin (including shared
writeable mmap) can count on it doing the right thing with respect to
growing inline data to an extent tree.
Size reducing truncates, including UNRESVP can simply zero that portion of
the inode block being removed. Size increasing truncatesm, including RESVP
have to be a little bit smarter and grow the inode to an extent tree if
necessary.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
This hooks up ocfs2_readpage() to populate a page with data from an inode
block. Direct IO reads from inline data are modified to fall back to
buffered I/O. Appropriate checks are also placed in the extent map code to
avoid reading an extent list when inline data might be stored.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
Add the disk, network and memory structures needed to support data in inode.
Struct ocfs2_inline_data is defined and embedded in ocfs2_dinode for storing
inline data.
A new inode field, i_dyn_features, is added to facilitate tracking of
dynamic inode state. Since it will be used often, we want to mirror it on
ocfs2_inode_info, and transfer it via the meta data lvb.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
The check to see if a new dirent would fit in an old one is pretty ugly, and
it's done at least twice. Clean things up by putting this in it's own
easier-to-read function.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
scsi/scsi_transport_iscsi.h uses struct mutex and struct list_head,
so while linux/mutex.h and linux/list.h seem to be pulled in indirectly
by one of the headers it includes, the right thing
is to include linux/mutex.h and linus/list.h directly.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ocfs2_rename() does direct manipulation of the dirent it's gotten back from
a directory search. Wrap this manipulation inside of a function so that we
can transparently change directory update behavior in the future. As an
added bonus, this gets rid of an ugly macro.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
A couple paths which needed to just match a parent dir + name pair to an
inode number were a bit messy because they had to deal with
ocfs2_find_files_on_disk() which returns a larger number of values. Provide
a convenience function, ocfs2_lookup_ino_from_name() which internalizes all
the extra accounting.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
We can preserve the behavior of ocfs2_empty_dir(), while getting rid of the
open coded directory walk by just providing a smart filldir callback. This
also automatically gets to use the dir readahead code, though in this case
any advantage is minor at best.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
ocfs2_queue_orphans() has an open coded readdir loop which can easily just
use a directory accessor function.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
filldir_t can take this, so don't turn de->inode into a 32 bit value. Right
now this doesn't make a difference since no ocfs2 inodes overflow that, but
it could be a nasty surprise later on if some kernel code is calling
ocfs2_dir_foreach_blk() and expecting real inode numbers back...
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
Put this in it's own function so that the functionality can be overridden.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
The code for adding, removing, deleting directory entries was splattered all
over namei.c. I'd rather have this all centralized, so that it's easier to
make changes for inline dir data, and eventually indexed directories.
None of the code in any of the functions was changed. I only removed the
static keyword from some prototypes so that they could be exported.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
We'll want to reuse most of this when pushing inline data back out to an
extent. Keeping this part as a seperate patch helps to keep the upcoming
changes for write support uncluttered.
The core portion of ocfs2_zero_cluster_pages() responsible for making sure a
page is mapped and properly dirtied is abstracted out into it's own
function, ocfs2_map_and_dirty_page(). Actual functionality doesn't change,
though zeroing becomes optional.
We also turn part of ocfs2_free_write_ctxt() into a common function for
unlocking and freeing a page array. This operation is very common (and
uniform) for Ocfs2 cluster sizes greater than page size, so it makes sense
to keep the code in one place.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
By doing this, we can remove any higher level logic which has to have
knowledge of btree functionality - any callers of ocfs2_write_begin() can
now expect it to do anything necessary to prepare the inode for new data.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Reviewed-by: Joel Becker <joel.becker@oracle.com>
The Coverity checker spotted that we have already oops'ed if "cmd"
was NULL.
Since "cmd" being NULL doesn't seem to be possible at this point this
patch removes the NULL check.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Implement sops->show_options() so as to allow /proc/mounts to show the mount
options.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
This is technically harmless (recovery will clean it out later), but leaves
a bogus entry in the slot_map which really shouldn't be there.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
