This patch adds preferences field to the p9_trans_module.
Through this, now transport layer can express its preference about the
payload. i.e if payload neds to be part of the PDU or it prefers it
to be sent sepearetly so that the transport layer can handle it in
a better way.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Modify p9_virtio_request() and req_done() functions to support
additional payload sent down to the transport layer through
tc->pubuf and tc->pkbuf.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This will be used by the transport layer to determine the out going
request type. Transport layer uses this information to correctly
place the mapped pages in the PDU. Patches following this will make
use of this to achieve zero copy.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
This patch prepares p9_fcall structure for zero copy. Added
fields send the payload buffer information to the transport layer.
In addition it adds a 'private' field for the transport layer to
store mapped/pinned page information so that it can be freed/unpinned
during req_done.
This patch also creates trans_common.[ch] to house helper functions.
It adds the following helper functions.
p9_release_req_pages - Release pages after the transaction.
p9_nr_pages - Return number of pages needed to accomodate the payload.
payload_gup - Translates user buffer into kernel pages.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Current code sets access=user as default for all protocol versions.
This patch chagnes it to "client" only for dotl.
User can always specify particular access mode with -o access= option.
No change there.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The mount option access=client is overloaded as it assumes acl too.
Adding posixacl option to enable POSIX ACLs makes it explicit and clear.
Also it is convenient in the future to add other types of acls like richacls.
Ideally, the access mode 'client' should be just like V9FS_ACCESS_USER
except it underscores the location of access check.
Traditional 9P protocol lets the server perform access checks but with
this mode, all the access checks will be performed on the client itself.
Server just follows the client's directive.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
If the kernel is not compiled with CONFIG_9P_FS_POSIX_ACL and the
mount option is specified to enable ACLs current code fails the mount.
This patch brings the behavior inline with other filesystems like ext3
by proceeding with the mount and log a warning to syslog.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
With create/mkdir/mknod in non cached mode we initialize the inode using
v9fs_get_inode. v9fs_get_inode doesn't initialize the cache inode value
to NULL. This is causing to trip on BUG_ON in v9fs_get_cached_acl.
Fix is to initialize acls to NULL and not to leave them in ACL_NOT_CACHED
state.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
In v9fs_get_acl() if __v9fs_get_acl() gets only one of the
dacl/pacl we are not releasing it.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
This patch includes the implementation of the clock gating
for System MMU. Initially, all System MMUs are not asserted
the system clock. Asserting the system clock to a System MMU
is enabled only when s5p_sysmmu_enable() is called. Likewise,
it is disabled only when s5p_sysmmu_disable() is called.
Therefore, clock gating on System MMUs are still invisible to
the outside of the System MMU driver.
Signed-off-by: KyongHo Cho <pullip.cho@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch includes the following enhancements for System MMU:
- Enhanced readability
- Removal of unused data structures or their members
- Simplified function definitions
- Corrections of some logical errors
- Full compliance with Linux coding style
- Simpler way of registering callback functions of System MMU faults
Signed-off-by: KyongHo Cho <pullip.cho@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Structures ip6t_replace, compat_ip6t_replace, and xt_get_revision are
copied from userspace. Fields of these structs that are
zero-terminated strings are not checked. When they are used as argument
to a format string containing "%s" in request_module(), some sensitive
information is leaked to userspace via argument of spawned modprobe
process.
The first bug was introduced before the git epoch; the second was
introduced in 3bc3fe5e (v2.6.25-rc1); the third is introduced by
6b7d31fc (v2.6.15-rc1). To trigger the bug one should have
CAP_NET_ADMIN.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Structures ipt_replace, compat_ipt_replace, and xt_get_revision are
copied from userspace. Fields of these structs that are
zero-terminated strings are not checked. When they are used as argument
to a format string containing "%s" in request_module(), some sensitive
information is leaked to userspace via argument of spawned modprobe
process.
The first and the third bugs were introduced before the git epoch; the
second was introduced in 2722971c (v2.6.17-rc1). To trigger the bug
one should have CAP_NET_ADMIN.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Structures ipt_replace, compat_ipt_replace, and xt_get_revision are
copied from userspace. Fields of these structs that are
zero-terminated strings are not checked. When they are used as argument
to a format string containing "%s" in request_module(), some sensitive
information is leaked to userspace via argument of spawned modprobe
process.
The first bug was introduced before the git epoch; the second is
introduced by 6b7d31fc (v2.6.15-rc1); the third is introduced by
6b7d31fc (v2.6.15-rc1). To trigger the bug one should have
CAP_NET_ADMIN.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
A potential race condition when generating connlimit_rnd is also fixed.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
We use the reply tuples when limiting the connections by the destination
addresses, however, in SNAT scenario, the final reply tuples won't be
ready until SNAT is done in POSTROUING or INPUT chain, and the following
nf_conntrack_find_get() in count_tem() will get nothing, so connlimit
can't work as expected.
In this patch, the original tuples are always used, and an additional
member addr is appended to save the address in either end.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds support for gpio interrupts on Samsung EXYNOS4 platform.
Common s5p-gpioint.c code is used for handling gpio interrupts. Each gpio
line that needs gpio interrupt support must be later registered with
s5p_register_gpio_interrupt() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes all global data from common s5p gpio interrupt
handler code. This enables to reuse this code on EXYNOS4 platform.
Instead of global data (IRQ_GPIOINT interrupt number,
S5P_GPIOINT_GROUP_MAXNR groups count), a s5p_register_gpioint_bank()
function is introduced. It is aimed to be called from gpiolib init.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch performs a global cleanup in s5p gpio interrupt support code.
The code is prepared for upcoming support for gpio interrupts on EXYNOS4
platform, which has 2 gpio banks (regions) instead of one (like on
S5PC110 and S5PC100).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds missing GPYx gpio banks on Samsung EXYNOS4 platform.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The cpufreq init function is referenced from the driver structure and
we don't appear to have annotations which allow us to mark that it'll
never be called after system init, causing the linker consistency
infrastructure to complain. Just remove the __init annotation to avoid
noise from the build.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to support keypad device to the SMDKV310 board.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The keypad IF on EXYNOS4 uses 100MHz from PERIR functional
block for clocks, this patch updates the same.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates the keypad IF base address in the memory map
for EXYNOS4.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the samsung_keypad_cfg_gpio() for EXYNOS4.
Now, this helpers are only for keypad operating in PORT-0.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The EDGE Port module of some ColdFire parts using the intc-simr interrupt
controller provides support for 7 external interrupts. These interrupts
go off-chip (that is they are not for internal peripherals). They need
some special handling and have some extra setup registers. Add code to
support them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The EDGE Port module of some ColdFire parts using the intc-2 interrupt
controller provides support for 7 external interrupts. These interrupts
go off-chip (that is they are not for internal peripherals). They need
some special handling and have some extra setup registers. Add code to
support them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The reality is that you do not need the abiltity to configure the
clock divider for ColdFire CPUs. It is a fixed ratio on any given
ColdFire family member. It is not the same for all ColdFire parts,
but it is always the same in a model range. So hard define the divider
for each supported ColdFire CPU type and remove the Kconfig option.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5407/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5407/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5407/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/532x/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/532x/gpio.c:54:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5307/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5307/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5307/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/527x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:38:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:39:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:54:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/527x/gpio.c:55:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5272/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:67:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:68:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5272/gpio.c:69:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5249/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5249/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/523x/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:38:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/523x/gpio.c:53:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
rch/m68knommu/platform/520x/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:51:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/520x/gpio.c:52:3: warning: initialisation makes pointer from integer without a cast
...
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5206e/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast CC kernel/panic.o
arch/m68knommu/platform/5206e/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5206e/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Fix these compiler warnings:
arch/m68knommu/platform/5206/gpio.c:35:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5206/gpio.c:36:3: warning: initialisation makes pointer from integer without a cast
arch/m68knommu/platform/5206/gpio.c:37:3: warning: initialisation makes pointer from integer without a cast
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The intc-simr interrupt controller on some ColdFire CPUs has a set range of
interrupts its supports (64 through 128 or 192 depending on model). We
shouldn't be setting this handler for every possible interrupt from 0 to
255. Set more appropriate limits, and this means we can drop the interrupt
number check in the mask and unmask routines.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Use a proper irq_startup() routine to intialize the interrupt priority
and level register in the ColdFire intc-2 controller code. We shouldn't
be checking if the priority/level has been set on every unmask operation.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The intc-2 interrupt controller on some ColdFire CPUs has a set range of
interrupts its supports (64 through 128 or 192 depending on model). We
shouldn't be setting this handler for every possible interrupt from 0 to
255. Set more appropriate limits, and this means we can drop the interrupt
number check in the mask and unmask routines.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The FireBee is a ColdFire 5475 based board. Add a configuration option
to support it, and the basic platform flash layout code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Most ColdFire CPUs have an internal peripheral set that can be mapped at
a user selectable address. Different ColdFire parts either use an MBAR
register of an IPSBAR register to map the peripheral region. Most boards
use the Freescale default mappings - but not all.
Make the setting of the MBAR or IPSBAR register configurable. And only make
the selection available on the appropriate ColdFire CPU types.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Different ColdFire CPUs have different ways of defining where their
internal peripheral registers sit in their address space. Some use an
MBAR register, some use and IPSBAR register, some have a fixed mapping.
Now that most of the peripheral address definitions have been cleaned up
we can clean up the setting of the MBAR and IPSBAR defines to limit them
to just where they are needed (and where they actually exist).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
In some of the RAM size autodetection code on ColdFire CPU startup
we reference DRAM registers relative to the MBAR register. Not all of
the supported ColdFire CPUs have an MBAR, and currently this works
because we fake an MBAR address on those registers. In an effort to
clean this up, and eventually remove the fake MBAR setting make the
DRAM register address definitions actually contain the MBAR (or IPSBAR
as appropriate) value as required.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Not all ColdFire CPUs that use the old style timer hardware module use
an MBAR set peripheral region. Move the TIMER base address defines to the
per-CPU header files where we can set it correctly based on how the
peripherals are mapped - instead of using a fake MBAR for some platforms.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
