This build failure:
arch/powerpc/sysdev/mpic.c:810: error: conflicting types for 'mpic_set_affinity'
arch/powerpc/sysdev/mpic.h:39: error: previous declaration of 'mpic_set_affinity' was here
make[2]: *** [arch/powerpc/sysdev/mpic.o] Error 1
make[2]: *** Waiting for unfinished jobs....
Triggers because the function prototype was not updated when the
function call signature got changed by:
d5dedd4: irq: change ->set_affinity() to return status
[ Impact: build fix on powerpc ]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On mount, "sec=ntlmssp" can now be specified to allow
"rawntlmssp" security to be enabled during
CIFS session establishment/authentication (ntlmssp used to
require specifying krb5 which was counterintuitive).
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patch adds code that can benchmark the ring buffer as well as
test it. This code can be compiled into the kernel (not recommended)
or as a module.
A separate ring buffer is used to not interfer with other users, like
ftrace. It creates a producer and a consumer (option to disable creation
of the consumer) and will run for 10 seconds, then sleep for 10 seconds
and then repeat.
While running, the producer will write 10 byte loads into the ring
buffer with just putting in the current CPU number. The reader will
continually try to read the buffer. The reader will alternate from reading
the buffer via event by event, or by full pages.
The output is a pr_info, thus it will fill up the syslogs.
Starting ring buffer hammer
End ring buffer hammer
Time: 9000349 (usecs)
Overruns: 12578640
Read: 5358440 (by events)
Entries: 0
Total: 17937080
Missed: 0
Hit: 17937080
Entries per millisec: 1993
501 ns per entry
Sleeping for 10 secs
Starting ring buffer hammer
End ring buffer hammer
Time: 9936350 (usecs)
Overruns: 0
Read: 28146644 (by pages)
Entries: 74
Total: 28146718
Missed: 0
Hit: 28146718
Entries per millisec: 2832
353 ns per entry
Sleeping for 10 secs
Time: is the time the test ran
Overruns: the number of events that were overwritten and not read
Read: the number of events read (either by pages or events)
Entries: the number of entries left in the buffer
(the by pages will only read full pages)
Total: Entries + Read + Overruns
Missed: the number of entries that failed to write
Hit: the number of entries that were written
The above example shows that it takes ~353 nanosecs per entry when
there is a reader, reading by pages (and no overruns)
The event by event reader slowed the producer down to 501 nanosecs.
[ Impact: see how changes to the ring buffer affect stability and performance ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Fix a trivial typo in Documentation/x86/x86_64/mm.txt.
[ Impact: documentation only ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Rik van Riel <riel@redhat.com>
Extend the maximum addressable memory on x86-64 from 2^44 to
2^46 bytes. This requires some shuffling around of the vmalloc
and virtual memmap memory areas, to keep them away from the
direct mapping of up to 64TB of physical memory.
This patch also introduces a guard hole between the vmalloc
area and the virtual memory map space. There's really no
good reason why we wouldn't have a guard hole there.
[ Impact: future hardware enablement ]
Signed-off-by: Rik van Riel <riel@redhat.com>
LKML-Reference: <20090505172856.6820db22@cuia.bos.redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
In the hot path of the ring buffer "__rb_reserve_next" there's a big
if statement that does not even return back to the work flow.
code;
if (cross to next page) {
[ lots of code ]
return;
}
more code;
The condition is even the unlikely path, although we do not denote it
with an unlikely because gcc is fine with it. The condition is true when
the write crosses a page boundary, and we need to start at a new page.
Having this if statement makes it hard to read, but calling another
function to do the work is also not appropriate, because we are using a lot
of variables that were set before the if statement, and we do not want to
send them as parameters.
This patch changes it to a goto:
code;
if (cross to next page)
goto next_page;
more code;
return;
next_page:
[ lots of code]
This makes the code easier to understand, and a bit more obvious.
The output from gcc is practically identical. For some reason, gcc decided
to use different registers when I switched it to a goto. But other than that,
the logic is the same.
[ Impact: easier to read code ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
We were not setting the SMB uid in NTLMSSP authenticate
request which could lead to INVALID_PARAMETER error
on 2nd session setup.
Signed-off-by: Steve French <sfrench@us.ibm.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/r128: fix r128 ioremaps to use ioremap_wc.
drm: cleanup properly in drm_get_dev() failure paths
drm: clean the map list before destroying the hash table
drm: remove unreachable code in drm_sysfs.c
drm: add control node checks missing from kms merge
drm/kms: don't try to shortcut drm mode set function
drm/radeon: bump minor version for occlusion queries support
When adding the EXPORT_SYMBOL to some of the tracing API, I accidently
used EXPORT_SYMBOL instead of EXPORT_SYMBOL_GPL. This patch fixes
that mistake.
[ Impact: export the tracing code only for GPL modules ]
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The only references in the kernel to the .text.sched section are in
recordmcount.pl. Since the code it has is intended to be example code
it should refer to real kernel sections. So change it to .sched.text
instead.
[ Impact: consistency in comments ]
Signed-off-by: Tim Abbott <tabbott@mit.edu>
LKML-Reference: <1241136371-10768-1-git-send-email-tabbott@mit.edu>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
madvise(MADV_WILLNEED) forces page cache readahead on a range of memory
backed by a file. The assumption is made that the page required is
order-0 and "normal" page cache.
On hugetlbfs, this assumption is not true and order-0 pages are
allocated and inserted into the hugetlbfs page cache. This leaks
hugetlbfs page reservations and can cause BUGs to trigger related to
corrupted page tables.
This patch causes MADV_WILLNEED to be ignored for hugetlbfs-backed
regions.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As a precaution, it is best to disable writing to the ring buffers
when reseting them.
[ Impact: prevent weird things if write happens during reset ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In the swap page ring buffer code that is used by the ftrace splice code,
we scan the page to increment the counter of entries read.
With the number of entries already in the page we simply need to add it.
[ Impact: speed up reading page from ring buffer ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When an upstream port reports an AER error to root port, kernel
starts error recovery procedures. The default return value of
function pcie_portdrv_slot_reset is PCI_ERS_RESULT_NONE. If all
port service drivers of the downstream port under the upstream
port have no slot_reset method in pci_error_handlers, AER recovery
would stop without resume. Below patch against 2.6.30-rc3 fixes it.
Signed-off-by: Zhang Yanmin <yanmin.zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
disable_irq() should wait for all running handlers to complete
before returning. As such, if it's used to disable an interrupt
from that interrupt's handler it will deadlock. This replaces
the dangerous instances with the _nosync() variant which doesn't
have this problem.
Note the 2 handlers in question are only used #ifdef DEBUG so
I imagine these code paths don't get hit often.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'irq/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Revert "genirq: assert that irq handlers are indeed running in hardirq context"
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: x86, mmiotrace: fix range test
tracing: fix ref count in splice pages
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: show number of core_siblings instead of thread_siblings in /proc/cpuinfo
amd-iommu: fix iommu flag masks
x86: initialize io_bitmap_base on 32bit
x86: gettimeofday() vDSO: fix segfault when tv == NULL
- drivers/xen/events.c did not compile
- xen_setup_hook caused a modpost section warning
- the use of u64 (instead of unsigned long long) together with a %llu
in drivers/xen/balloon.c caused a compiler warning
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently, when the ring buffer writer overflows the buffer and must
write over non consumed data, we increment the overrun counter by
reading the entries on the page we are about to overwrite. This reads
the entries one by one.
This is not very effecient. This patch adds another entry counter
into each buffer page descriptor that keeps track of the number of
entries on the page. Now on overwrite, the overrun counter simply
needs to add the number of entries that is on the page it is about
to overwrite.
[ Impact: speed up of ring buffer in overwrite mode ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As a kernel thread, rcu_sched_grace_period() runs with all signals ignored.
It can never receive a signal even if it sleeps in TASK_INTERRUPTIBLE, it
needs the explicit allow_signal() to be visible for signals.
[ Impact: reduce kernel size, remove dead code ]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <20090503211118.GA22973@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The entries counter in cpu buffer is not atomic. It can be updated by
other interrupts or from another CPU (readers).
But making entries into "atomic_t" causes an atomic operation that can
hurt performance. Instead we convert it to a local_t that will increment
a counter with a local CPU atomic operation (if the arch supports it).
Instead of fighting with readers and overwrites that decrement the counter,
I added a "read" counter. Every time a reader reads an entry it is
incremented.
We already have a overrun counter and with that, the entries counter and
the read counter, we can calculate the total number of entries in the
buffer with:
(entries - overrun) - read
As long as the total number of entries in the ring buffer is less than
the word size, this will work. But since the entries counter was previously
a long, this is no different than what we had before.
Thanks to Andrew Morton for pointing out in the first version that
atomic_t does not replace unsigned long. I switched to atomic_long_t
even though it is signed. A negative count is most likely a bug.
[ Impact: keep accurate count of cpu buffer entries ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Thomas noted that we should disallow sysctl_sched_rt_runtime == 0 for
(!RT_GROUP) since the root group always has some RT tasks in it.
Further, update the documentation to inspire clue.
[ Impact: exclude corner-case sysctl_sched_rt_runtime value ]
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20090505155436.863098054@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds stats to the ftrace ring buffers:
# cat /debugfs/tracing/per_cpu/cpu0/stats
entries: 42360
overrun: 30509326
commit overrun: 0
nmi dropped: 0
Where entries are the total number of data entries in the buffer.
overrun is the number of entries not consumed and were overwritten by
the writer.
commit overrun is the number of entries dropped due to nested writers
wrapping the buffer before the initial writer finished the commit.
nmi dropped is the number of entries dropped due to the ring buffer
lock being held when an nmi was going to write to the ring buffer.
Note, this field will be meaningless and will go away when the ring
buffer becomes lockless.
[ Impact: let userspace know what is happening in the ring buffers ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The WARN_ON in the ring buffer when a commit is preempted and the
buffer is filled by preceding writes can happen in normal operations.
The WARN_ON makes it look like a bug, not to mention, because
it does not stop tracing and calls printk which can also recurse, this
is prone to deadlock (the WARN_ON is not in a position to recurse).
This patch removes the WARN_ON and replaces it with a counter that
can be retrieved by a tracer. This counter is called commit_overrun.
While at it, I added a nmi_dropped counter to count any time an NMI entry
is dropped because the NMI could not take the spinlock.
[ Impact: prevent deadlock by printing normal case warning ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
I'm adding a module to do a series of tests on the ring buffer as well
as benchmarks. This module needs to have more of the ring buffer API
exported. There's nothing wrong with reading the ring buffer from a
module.
[ Impact: allow modules to read pages from the ring buffer ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
This patch fixes the wrong message type that are triggered by
user updates, the following commands:
(term1)# conntrack -I -p tcp -s 1.1.1.1 -d 2.2.2.2 -t 10 --sport 10 --dport 20 --state LISTEN
(term1)# conntrack -U -p tcp -s 1.1.1.1 -d 2.2.2.2 -t 10 --sport 10 --dport 20 --state SYN_SENT
(term1)# conntrack -U -p tcp -s 1.1.1.1 -d 2.2.2.2 -t 10 --sport 10 --dport 20 --state SYN_RECV
only trigger event message of type NEW, when only the first is NEW
while others should be UPDATE.
(term2)# conntrack -E
[NEW] tcp 6 10 LISTEN src=1.1.1.1 dst=2.2.2.2 sport=10 dport=20 [UNREPLIED] src=2.2.2.2 dst=1.1.1.1 sport=20 dport=10 mark=0
[NEW] tcp 6 10 SYN_SENT src=1.1.1.1 dst=2.2.2.2 sport=10 dport=20 [UNREPLIED] src=2.2.2.2 dst=1.1.1.1 sport=20 dport=10 mark=0
[NEW] tcp 6 10 SYN_RECV src=1.1.1.1 dst=2.2.2.2 sport=10 dport=20 [UNREPLIED] src=2.2.2.2 dst=1.1.1.1 sport=20 dport=10 mark=0
This patch also removes IPCT_REFRESH from the bitmask since it is
not of any use.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch fixes a problem when you use 32 nodes in the cluster
match:
% iptables -I PREROUTING -t mangle -i eth0 -m cluster \
--cluster-total-nodes 32 --cluster-local-node 32 \
--cluster-hash-seed 0xdeadbeef -j MARK --set-mark 0xffff
iptables: Invalid argument. Run `dmesg' for more information.
% dmesg | tail -1
xt_cluster: this node mask cannot be higher than the total number of nodes
The problem is related to this checking:
if (info->node_mask >= (1 << info->total_nodes)) {
printk(KERN_ERR "xt_cluster: this node mask cannot be "
"higher than the total number of nodes\n");
return false;
}
(1 << 32) is 1. Thus, the checking fails.
BTW, I said this before but I insist: I have only tested the cluster
match with 2 nodes getting ~45% extra performance in an active-active setup.
The maximum limit of 32 nodes is still completely arbitrary. I'd really
appreciate if people that have more nodes in their setups let me know.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-algo-pca: Let PCA9564 recover from unacked data byte (state 0x30)
i2c-algo-bit: Fix timeout test
i2c: Timeouts off by 1
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
e1000: fix virtualization bug
bonding: fix alb mode locking regression
Bluetooth: Fix issue with sysfs handling for connections
usbnet: CDC EEM support (v5)
tcp: Fix tcp_prequeue() to get correct rto_min value
ehea: fix invalid pointer access
ne2k-pci: Do not register device until initialized.
Subject: [PATCH] br2684: restore net_dev initialization
net: Only store high 16 bits of kernel generated filter priorities
virtio_net: Fix function name typo
virtio_net: Cleanup command queue scatterlist usage
bonding: correct the cleanup in bond_create()
virtio: add missing include to virtio_net.h
smsc95xx: add support for LAN9512 and LAN9514
smsc95xx: configure LED outputs
netconsole: take care of NETDEV_UNREGISTER event
xt_socket: checks for the state of nf_conntrack
bonding: bond_slave_info_query() fix
cxgb3: fixing gcc 4.4 compiler warning: suggest parentheses around operand of ‘!’
netfilter: use likely() in xt_info_rdlock_bh()
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix setting of oprofile cpu type
powerpc: Update MPC5xxx and Xilinx Virtex maintainer entries
powerpc adjust oprofile_cpu_type version 3
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
net/9p: handle correctly interrupted 9P requests
net/9p: return error when p9_client_stat fails
net/9p: set correct stat size when sending Twstat messages
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mvsdio: fix CONFIG_PM=y build
mmci: fix crash with debug enabled
sdhci: catch ADMA errors
mmc: increase power up delay
sdhci-pci: bad error handling in probe function
mmc_block: be prepared for oversized requests
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Remove BROKEN from mpc5200 kconfig
ASoC: TWL4030: Fix gain control for earpiece amplifier
ALSA: pcm core - Avoid jiffies check for devices with BATCH flag
ALSA: Add missing SNDRV_PCM_INFO_BATCH flag to some drivers
ALSA: indigo-express: add missing 64KHz flags
ASoC: Set the MPC5200 i2s driver to BROKEN status.
ASoC: Fix logic in WM8350 master clocking check
With 5 bits and 1.5 dB per step, the DXS volume range is only 48 dB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove most of the serial port parameters from the card longname string
because it was way too long and overflowed into the mixername string.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As packets ending with NEXTHDR_NONE don't have a last extension header,
the check for the length needs to be after the check for NEXTHDR_NONE.
Signed-off-by: Christoph Paasch <christoph.paasch@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Pointed out by Dave Miller:
CHECK include/linux/netfilter (57 files)
/home/davem/src/GIT/net-2.6/usr/include/linux/netfilter/xt_LED.h:6: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The mis-typing exist in dapm controller definitions and dapm route definitions,
so happen mis-matched error when snd_soc_dapm_add_routes().
Cc: stable@kernel.org
Signed-off-by: Jinyoung Park <parkjy@mtekvision.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com
