For pcie nic, after setting link speed and there is no link driver does not need
to do phy reset until link up.
For some pcie nics, to do this will also reset phy speed down counter and prevent
phy from auto speed down.
This patch fix the issue reported in following link.
1547151
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware now tells us that the reset is done by passing a magic value
via register. Use it to shorten the wait in case this is supported.
With old firmware, we still wait until the timeout is reached.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently sctp_sendmsg() triggers some calls that will allocate memory
with GFP_ATOMIC even when not necessary. In the case of
sctp_packet_transmit it will allocate a linear skb that will be used to
construct the packet and this may cause sends to fail due to ENOMEM more
often than anticipated specially with big MTUs.
This patch thus allows it to inherit gfp flags from upper calls so that
it can use GFP_KERNEL if it was triggered by a sctp_sendmsg call or
similar. All others, like retransmits or flushes started from BH, are
still allocated using GFP_ATOMIC.
In netperf tests this didn't result in any performance drawbacks when
memory is not too fragmented and made it trigger ENOMEM way less often.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we want to change a flow using netlink, we have to identify it to
be able to perform a lookup. Both the flow key and unique flow ID
(ufid) are valid identifiers, but we always have to specify the flow
key in the netlink message. When both attributes are there, the ufid
is used. The flow key is used to validate the actions provided by
the userland.
This commit allows to use the ufid without having to provide the flow
key, as it is already done in the netlink 'flow get' and 'flow del'
path. The flow key remains mandatory when an action is provided.
Signed-off-by: Samuel Gauthier <samuel.gauthier@6wind.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On AT91 SoCs, the User Register (USRIO) exposes a switch to configure the
"Reduced" or "Traditional" version of the Media Independent Interface
(RMII vs. MII or RGMII vs. GMII).
As on the older EMAC version, on GMAC, this switch is set by default to the
non-reduced type of interface, so use the existing capability and extend it to
GMII as well. We then keep the current logic in the macb_init() function.
The capabilities of sama5d2, sama5d4 and sama5d3 GEM interface are updated in
the macb_config structure to be able to properly enable them with a traditional
interface (GMII or MII).
Reported-by: Romain HENRIET <romain.henriet@l-acoustics.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e5a03bfd87 ("phy: Add an mdio_device structure") removed addr,
bus and dev member of the phy_device structure.
This patch remove the documentation about those members.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant says:
====================
xen-netback: fix multiple extra info handling
If a frontend passes multiple extra info fragments to netback on the guest
transmit side, because xen-netback does not account for this properly, only
a single ack response will be sent. This will eventually cause processing
of the shared ring to wedge.
This series re-imports the canonical netif.h from Xen, where the ring
protocol documentation has been updated, fixes this issue in xen-netback
and also adds a patch to reduce log spam.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the "prepare for reconnect" pr_info in xenbus.c. It's largely
uninteresting and the states of the frontend and backend can easily be
observed by watching the (o)xenstored log.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code does not currently support a frontend passing multiple extra info
fragments to the backend in a tx request. The xenvif_get_extras() function
handles multiple extra_info fragments but make_tx_response() assumes there
is only ever a single extra info fragment.
This patch modifies xenvif_get_extras() to pass back a count of extra
info fragments, which is then passed to make_tx_response() (after
possibly being stashed in pending_tx_info for deferred responses).
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The canonical netif header (in the Xen source repo) and the Linux variant
have diverged significantly. Recently much documentation has been added to
the canonical header which is highly useful for developers making
modifications to either xen-netfront or xen-netback. This patch therefore
re-imports the canonical header in its entirity.
To maintain compatibility and some style consistency with the old Linux
variant, the header was stripped of its emacs boilerplate, and
post-processed and copied into place with the following commands:
ed -s netif.h << EOF
H
,s/NETTXF_/XEN_NETTXF_/g
,s/NETRXF_/XEN_NETRXF_/g
,s/NETIF_/XEN_NETIF_/g
,s/XEN_XEN_/XEN_/g
,s/netif/xen_netif/g
,s/xen_xen_/xen_/g
,s/^typedef.*$//g
,s/^ /${TAB}/g
w
$
w
EOF
indent --line-length 80 --linux-style netif.h \
-o include/xen/interface/io/netif.h
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds macro NETCONFA_ALL to represent all type of netconf
attributes for IPv4 and IPv6.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Raspberry Pi Foundation's firmware updates are shipping device
trees using the old string, so we'll keep recognizing that as this rev
of V3D. Still, we should use a more specific name in the upstream DT
to clarify which board is being supported, in case we do other revs of
V3D in the future.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
prior to this patch, at the beginning if we have two paths in one assoc,
they may have the same params other than the last_time_heard, it will try
the paths like this:
1st cycle
try trans1 fail.
then trans2 is selected.(cause it's last_time_heard is after trans1).
2nd cycle:
try trans2 fail
then trans2 is selected.(cause it's last_time_heard is after trans1).
3rd cycle:
try trans2 fail
then trans2 is selected.(cause it's last_time_heard is after trans1).
....
trans1 will never have change to be selected, which is not what we expect.
we should keeping round robin all the paths if they are just added at the
beginning.
So at first every tranport's last_time_heard should be initialized 0, so
that we ensure they have the same value at the beginning, only by this,
all the transports could get equal chance to be selected.
Then for sctp_trans_elect_best, it should return the trans_next one when
*trans == *trans_next, so that we can try next if it fails, but now it
always return trans. so we can fix it by exchanging these two params when
we calls sctp_trans_elect_tie().
Fixes: 4c47af4d5e ('net: sctp: rework multihoming retransmission path selection to rfc4960')
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull turbostat updates for 4.6 from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: bugfix: TDP MSRs print bits fixing
tools/power turbostat: correct output for MSR_NHM_SNB_PKG_CST_CFG_CTL dump
tools/power turbostat: call __cpuid() instead of __get_cpuid()
tools/power turbostat: indicate SMX and SGX support
tools/power turbostat: detect and work around syscall jitter
tools/power turbostat: show GFX%rc6
tools/power turbostat: show GFXMHz
tools/power turbostat: show IRQs per CPU
tools/power turbostat: make fewer systems calls
tools/power turbostat: fix compiler warnings
tools/power turbostat: add --out option for saving output in a file
tools/power turbostat: re-name "%Busy" field to "Busy%"
tools/power turbostat: Intel Xeon x200: fix turbo-ratio decoding
tools/power turbostat: Intel Xeon x200: fix erroneous bclk value
tools/power turbostat: allow sub-sec intervals
tools/power turbostat: Decode MSR_MISC_PWR_MGMT
tools/power turbostat: decode HWP registers
x86 msr-index: Simplify syntax for HWP fields
tools/power turbostat: CPUID(0x16) leaf shows base, max, and bus frequency
tools/power turbostat: decode more CPUID fields
- GM20x secure boot support (hence, acceleration, finally \o/)
- GM200 support
- GM20B clock driver
- Support for power sensors on some GPUs
- Various other fixes all over the place
* 'linux-4.6' of git://github.com/skeggsb/linux: (95 commits)
drm/nouveau/clk/gm20b: add basic driver
drm/nouveau/clk/gk20a: share reusable structures/functions
drm/nouveau/clk/gk20a: set lowest frequency during init()
drm/nouveau/clk/gk20a: split gk20a_clk_new()
drm/nouveau/clk/gk20a: abstract pl_to_div
drm/nouveau/clk/gk20a: put mnp values into their own struct
drm/nouveau/clk/gk20a: emit parent rate as debug message
drm/nouveau/clk/gk20a: only restore divider to 1:1 if needed
drm/nouveau/clk/gk20a: only compute n_lo if needed
drm/nouveau/clk/gk20a: fix VCO bit mask
drm/nouveau/clk/gk20a: rename enable/disable functions
drm/nouveau/clk/gk20a: reorganize variables in gk20a_pllg_calc_mnp()
drm/nouveau/clk/gk20a: convert parameters to Khz
drm/nouveau/volt: add GM20B driver
drm/nouveau/volt/gk20a: split constructor
drm/nouveau/volt/gk20a: share reusable members & functions
drm/nouveau/ce/gm107: expose MaxwellDmaCopyA
drm/nouveau/fifo/gm107: KeplerChannelGpfifoB, and 2048 channels
drm/nouveau/fifo/gk110: expose KeplerChannelGpfifoB
drm/nouveau/fifo/gk104: submit NOP after all PBDMA_INTR_0, not just DEVICE
...
Add a basic clock driver that reuses the GK20A logic.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Make functions/structures that the GM20B driver will reuse public.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Err on the safe side by setting the lowest frequency (and thus voltage)
during device init.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This allows to instanciate drivers that use the same logic as gk20a with
different parameters.
Add a constructor function to allow other chips that inherit from this
clock to easily initialize its members
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
pl_to_div may be done differently depending on the chip. Abstract this
operation so the same logic can be reused for them as well.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This allows us to read them using one single function and will be handy
to the GM20B driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Most users are probably not interested in this information.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Only restore the 1:1 divider if it is not set already. Also use the
proper masks for this operation and add a second write as done in the
Android code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
n_lo is used if we are going to slide. Compute it only if that condition
succeeds to avoid confusion about future usage of this computation.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fix the mask specified to switch to VCO mode was given as an (incorrect)
immediate value. Although the side-effect happens to be the same, this
is clearly incorrect.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
gk20a_pllg_disable() is only used in the context of gk20a_clk_fini().
Move its body there and rename _gk20a_pllg_enable() and
_gk20a_pllg_disable() to non-underscored versions.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Move some variables declarations to the scope where they are actually
used to make the code easier to follow.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Perform computations in Khz instead of Mhz for better precision.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add basic GM20B volt driver that reuses the GK20A logic.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Split the constructor function so we can reuse the same logic in other
chips.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The CVB calculation and voltage setting functions can be reused for the
future chips. So move the declaration to gk20a.h.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This class supports a WFI method (0x0078) that's not present on the
KeplerChannelGpfifoA class.
The binary driver exposes both classes on these GPUs for some reason,
though there doesn't appear to be any difference in the setup that's
done for each (ie. even if you allocate GpfifoA, the WFI method will
still work).
We shall just expose GpfifoB, as I don't see a good reason to report
the presence of both.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
