When hardware has large FIFO, it is necessary to lower jiffies margin
by count of queued samples.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some hardware might have bigger FIFOs and DMA pointer value will be updated
in large chunks. Do not update hw_ptr_jiffies and position timestamp when
hw_ptr value was not changed.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For debugging purposes, it is better to separate actions.
Bit-values:
1: show bad PCM ring buffer pointer
2: show also stack (to debug kernel latency issues)
4: check pointer against system jiffies
Example:
5: show bad PCM ring buffer pointer and do jiffies check
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the fifo_size assignment to hw->ioctl callback to allow lowlevel
drivers overwrite the default behaviour.
fifo_size is in frames not bytes as specified in asound.h and alsa-lib's
documentation, but most hardware have fixed byte based FIFOs. Introduce
internal SNDRV_PCM_INFO_FIFO_IN_FRAMES.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Erase errors such as:
"Newly-erased block contained word 0xa4ef223e at offset 0x0296a014"
and failure to write the clean marker,
moves the offending erase block to erasing list before calling
jffs2_erase_failed(). This is bad as jffs2_erase_failed() will
also move the block to the bad_list, but is now moving the
wrong block, causing FS corruption.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The following patch fixes:
- re-initialization of host->col_addr which is used as byte index
between the successive READID flash commands.
- compile error when CONFIG_PM is enabled
- pass on the error code from clk_get()
- return -ENOMEM in case of failed ioremap()
- pass on the return value of platform_driver_probe() directly
- remove excessive printk
- let command line partition table parsing with mxc_nand name.
The cmd_line parsing is done via <mtd-id> name that differs
from mxc_nand by default and looks like "NAND 256MiB 1,8V 8-bit"
Signed-off-by: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Peter Zijlstra pointed out that under some circumstances, we can take
the mutex in a context or a counter and then swap that context or
counter to another task, potentially leading to lock order inversions
or the mutexes not protecting what they are supposed to protect.
This fixes the problem by making sure that we never take a mutex in a
context or counter which could get swapped to another task. Most of
the cases where we take a mutex is on a top-level counter or context,
i.e. a counter which has an fd associated with it or a context that
contains such a counter. This adds WARN_ON_ONCE statements to verify
that.
The two cases where we need to take the mutex on a context that is a
clone of another are in perf_counter_exit_task and
perf_counter_init_task. The perf_counter_exit_task case is solved by
uncloning the context before starting to remove the counters from it.
The perf_counter_init_task is a little trickier; we temporarily
disable context swapping for the parent (forking) task by setting its
ctx->parent_gen to the all-1s value after locking the context, if it
is a cloned context, and restore the ctx->parent_gen value at the end
if the context didn't get uncloned in the meantime.
This also moves the increment of the context generation count to be
within the same critical section, protected by the context mutex, that
adds the new counter to the context. That way, taking the mutex is
sufficient to ensure that both the counter list and the generation
count are stable.
[ Impact: fix hangs, races with inherited and PID counters ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18975.31580.520676.619896@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the build for CONFIG_NET_POLL_CONTROLLER that I broke with
217cbfa856 ("mac8390: fix regression
caused during net_device_ops conversion").
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not call t3_link_fault() under spinlock, as it calls msleep().
Besides, only the access to pi->link_fault needs to be serialized.
Also initialize local variables before checking the link status,
link state fields might otherwise end up containing garbage.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5e68b772e6
cxgb3: map entire Rx page, feed map+offset to Rx ring.
introduced a regression on platforms defining DECLARE_PCI_UNMAP_ADDR()
and related macros as no-ops.
Rx descriptors are fed with the a page buffer bus address + page chunk offset.
The page buffer bus address is set and retrieved through
pci_unamp_addr_set(), pci_unmap_addr().
These functions being meaningless on x86 (if CONFIG_DMA_API_DEBUG is not set).
The HW ends up with a bogus bus address.
This patch saves the page buffer bus address for all plaftorms.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH net-next] bonding: allow bond in mode balance-alb to work properly in bridge -try4.3
(updated)
changes v4.2 -> v4.3
- memcpy the address always, not just in case it differs from master->dev_addr
- compare_ether_addr_64bits() is not used so there is no direct need to make new
header file (I think it would be good to have bond stuff in separate file
anyway).
changes v4.1 -> v4.2
- use skb->pkt_type == PACKET_HOST compare rather then comparing skb dest addr
against skb->dev->dev_addr
The problem is described in following bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=487763
Basically here's what's going on. In every mode, bonding interface uses the same
mac address for all enslaved devices (except fail_over_mac). Only balance-alb
will simultaneously use multiple MAC addresses across different slaves. When you
put this kind of bond device into a bridge it will only add one of mac adresses
into a hash list of mac addresses, say X. This mac address is marked as local.
But this bonding interface also has mac address Y. Now then packet arrives with
destination address Y, this address is not marked as local and the packed looks
like it needs to be forwarded. This packet is then lost which is wrong.
Notice that interfaces can be added and removed from bond while it is in bridge.
***
When the multiple addresses for bridge port approach failed to solve this issue
due to STP I started to think other way to solve this. I returned to previous
solution but tweaked one.
This patch solves the situation in the bonding without touching bridge code.
For every incoming frame to bonding the destination address is compared to
current address of the slave device from which tha packet came. If these two
match destination address is replaced by mac address of the master. This address
is known by bridge so it is delivered properly. Note that the comparsion is not
made directly, it's used skb->pkt_type == PACKET_HOST instead. This is "set"
previously in eth_type_trans().
I experimentally tried that this works as good as searching through the slave
list (v4 of this patch).
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the korina driver poll the media
for link change. This is actually required on
Mikrotik RB532 (not RB532A) for korina to
operate properly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces dma_sync_single() with dma_sync_single_for_cpu() because
dma_sync_single() is an obsolete API; include/linux/dma-mapping.h says:
/* Backwards compat, remove in 2.7.x */
#define dma_sync_single dma_sync_single_for_cpu
#define dma_sync_sg dma_sync_sg_for_cpu
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipgre_tunnel_xmit() might need skb->dst, so tell dev_hard_start_xmit()
to no release it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clip_start_xmit() needs skb->dst so tell dev_hard_start_xmit()
to no release it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipip_tunnel_xmit() might need skb->dst, so tell dev_hard_start_xmit()
to no release it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduce the extra pass to allow the print-out to possibly
rely on already read counters.
[ Impact: cleanup ]
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Kacur <jkacur@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Always use NMI for performance-monitoring interrupt as there could be
racy situations if we switch between irq and nmi mode frequently.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
LKML-Reference: <20090529052835.GA13657@ywang-moblin2.bj.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This comment suggested storing two pieces of state in the
LLC skb control block, and in fact we do. Someone did
the implementation but never killed this todo comment :-)
Signed-off-by: David S. Miller <davem@davemloft.net>
The period_elapsed() call should be called when position moves.
The idea was taken from ALSA bug#4455.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Appearently, the used mask in the .pointer callback is invalid. It should
be in period_bytes range. The period_bytes is pow(2), so simple bitwise
operation is used.
Idea was taken from ALSA bug#4455.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the 'state_get' API call was added, we need to increase the minor
protocol version number so applications that depend on the can check
it's presence.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When the i2400m is connected to a network, the host interface (USB)
cannot be suspended. For that to happen, the device has to have
negotiated with the basestation to put the link on IDLE state.
If the host tries to put the device in standby while it is connected
but not idle, the device resets, as the driver should not do that.
To avoid triggering that, when the USB susbsytem requires the driver
to autosuspend the device, the driver checks if the device is not yet
idle. If it is not, the request is requested (will be retried again
later on after the autosuspend timeout). At some point the device will
enter idle and the request will succeed (unless of course, there is
network traffic, but at that point, there is no idle neither in the
link or the host interface).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
wimax connection manager / daemon has to know what is current
state of the device. Previously it was only possible to get
notification whet state has changed.
Note:
By mistake, the new generic netlink's number for
WIMAX_GNL_OP_STATE_GET was declared inserting into the existing list
of API calls, not appending; thus, it'd break existing API.
Fixed by Inaky Perez-Gonzalez <inaky@linux.intel.com> by moving to
the tail, where we add to the interface, not modify the interface.
Thanks to Stephen Hemminger <shemminger@vyatta.com> for catching this.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
From a fix by Cindy H Kao:
Block size has to be set before sending IOE enable because the
firmware reads the block size register before it reads IOE register.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Funcion documentation for wimax_msg_alloc() and wimax_msg_send() needs
to clarify that they can be used in the very early stages of a
wimax_dev lifecycle.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Functions i2400m_report_tlv*() are only called from
i2400m_report_hook(), called in a workqueue by
i2400m_report_hook_work(). The scheduler checks for device readiness
before scheduling.
Added an extra check for readiness in i2400m_report_hook_work(), which
makes all the checks down the line redundant.
Obviously the device state could change in the middle, but error
handling would take care of that.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
By running 'echo 1 > /sys/kernel/debug/wimax:wmxX/i2400m/trace_msg_from_user',
the driver will echo to user space all the commands being sent to the
device from user space, along with the responses.
However, this only helps with the commands being sent from user space;
with this patch, the trace hook is moved to i2400m_msg_to_dev(), which
is the single access point for running commands to the device (both by
user space and the kernel driver). This allows better debugging by
having a complete stream of commands/acks and reports.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When commands are sent from user space, trace both the command sent
and the answer received over the "echo" pipe instead of over the
"trace" pipe when command tracing is enabled. As well, when the device
sends a reports/indications, send it over the "echo" pipe.
The "trace" pipe is used by the device to send firmware traces;
gets confusing. Another named pipe makes it easier to split debug
information.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The WiMAX i2400m driver needs to generate a fake source MAC address to
fake an ethernet header (for destination, the card's MAC is
used). This is the source of the packet, which is the basestation it
came from. The basestation's mac address is not usable for this, as it
uses its own namespace and it is not always available.
Currently the fake source MAC address was being set to all zeros,
which was causing trouble with bridging.
Use random_ether_addr() to generate a proper one that creates no
trouble.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Testing the i7300_idle driver on i5000-series hardware required
an edit to i7300_idle.h to "#define SUPPORT_I5000 1" and a re-build
of both i7300_idle and ioat_dma.
Replace that build-time scheme with a load-time module parameter:
"7300_idle.forceload=1" to make it easier to test the driver
on hardware that while not officially validated, works fine
and is much more commonly available.
By default (no modparam) the driver will continue to load
only on the i7300.
Note that ioat_dma runs a copy of i7300_idle's probe routine
to know to reserve an IOAT channel for i7300_idle.
This change makes ioat_dma do that always on the i5000,
just like it does on the i7300.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Andrew Henroid <andrew.d.henroid@intel.com>
