The platform bus type is often used to handle Systems-on-a-Chip (SoC)
where all devices are represented by objects of type struct
platform_device. In those cases the same "platform" device driver
may be used with multiple different system configurations, but the
actions needed to put the devices it handles into a low-power state
and back into the full-power state may depend on the design of the
given SoC. The driver, however, cannot possibly include all the
information necessary for the power management of its device on all
the systems it is used with. Moreover, the device hierarchy in its
current form also is not suitable for representing this kind of
information.
The patch below attempts to address this problem by introducing
objects of type struct dev_power_domain that can be used for
representing power domains within a SoC. Every struct
dev_power_domain object provides a sets of device power
management callbacks that can be used to perform what's needed for
device power management in addition to the operations carried out by
the device's driver and subsystem.
Namely, if a struct dev_power_domain object is pointed to by the
pwr_domain field in a struct device, the callbacks provided by its
ops member will be executed in addition to the corresponding
callbacks provided by the device's subsystem and driver during all
power transitions.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-and-acked-by: Kevin Hilman <khilman@ti.com>
The variable pm_flags is used to prevent APM from being enabled
along with ACPI, which would lead to problems. However, acpi_init()
is always called before apm_init() and after acpi_init() has
returned, it is known whether or not ACPI will be used. Namely, if
acpi_disabled is not set after acpi_init() has returned, this means
that ACPI is enabled. Thus, it is sufficient to check acpi_disabled
in apm_init() to prevent APM from being enabled in parallel with
ACPI.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
After redefining CONFIG_PM to depend on (CONFIG_PM_SLEEP ||
CONFIG_PM_RUNTIME) the CONFIG_PM_OPS option is redundant and can be
replaced with CONFIG_PM.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If direct references to pm_flags are removed from drivers/acpi/bus.c,
CONFIG_ACPI will not need to depend on CONFIG_PM any more. Make that
happen.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
Currently, wakeup sysfs attributes are created for all devices,
regardless of whether or not they are wakeup-capable. This is
excessive and complicates wakeup device identification from user
space (i.e. to identify wakeup-capable devices user space has to read
/sys/devices/.../power/wakeup for all devices and see if they are not
empty).
Fix this issue by avoiding to create wakeup sysfs files for devices
that cannot wake up the system from sleep states (i.e. whose
power.can_wakeup flags are unset during registration) and modify
device_set_wakeup_capable() so that it adds (or removes) the relevant
sysfs attributes if a device's wakeup capability status is changed.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
For name_to_handle_at(2) we'll want both ...at()-style syscall that
would be usable for non-directory descriptors (with empty relative
pathname). Introduce new flag (AT_EMPTY_PATH) to deal with that and
corresponding LOOKUP_EMPTY; teach user_path_at() and path_init() to
deal with the latter.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit 45a52a0207 (NFS move nfs_client
initialization into nfs_get_client) introduces a new warning in
fs/nfs/idmap.c:
‘struct rpc_timeout’ declared inside parameter list
Fix it by adding a forward declaration for the struct rpc_timeout
in include/linux/nfs_xdr.h
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: NFSROOT should default to "proto=udp"
nfs4: remove duplicated #include
NFSv4: nfs4_state_mark_reclaim_nograce() should be static
NFSv4: Fix the setlk error handler
NFSv4.1: Fix the handling of the SEQUENCE status bits
NFSv4/4.1: Fix nfs4_schedule_state_recovery abuses
NFSv4.1 reclaim complete must wait for completion
NFSv4: remove duplicate clientid in struct nfs_client
NFSv4.1: Retry CREATE_SESSION on NFS4ERR_DELAY
sunrpc: Propagate errors from xs_bind() through xs_create_sock()
(try3-resend) Fix nfs_compat_user_ino64 so it doesn't cause problems if bit 31 or 63 are set in fileid
nfs: fix compilation warning
nfs: add kmalloc return value check in decode_and_add_ds
SUNRPC: Remove resource leak in svc_rdma_send_error()
nfs: close NFSv4 COMMIT vs. CLOSE race
SUNRPC: Close a race in __rpc_wait_for_completion_task()
The exportfs encode handle function should return the minimum required
handle size. This helps user to find out the handle size by passing 0
handle size in the first step and then redoing to the call again with
the returned handle size value.
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
New helpers: user_statfs() and fd_statfs(), taking userland pathname and
descriptor resp. and filling struct kstatfs. Syscalls of statfs family
(native, compat and foreign - osf and hpux on alpha and parisc resp.)
switched to those. Removes some boilerplate code, simplifies cleanup
on errors...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
new function: file_open_root(dentry, mnt, name, flags) opens the file
vfs_path_lookup would arrive to.
Note that name can be empty; in that case the usual requirement that
dentry should be a directory is lifted.
open-coded equivalents switched to it, may_open() got down exactly
one caller and became static.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
New lookup flag: LOOKUP_ROOT. nd->root is set (and held) by caller,
path_init() starts walking from that place and all pathname resolution
machinery never drops nd->root if that flag is set. That turns
vfs_path_lookup() into a special case of do_path_lookup() *and*
gets us down to 3 callers of link_path_walk(), making it finally
feasible to rip the handling of trailing symlink out of link_path_walk().
That will not only simply the living hell out of it, but make life
much simpler for unionfs merge. Trailing symlink handling will
become iterative, which is a good thing for stack footprint in
a lot of situations as well.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Don't stash the struct file * used as starting point of walk in nameidata;
pass file ** to path_init() instead.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
take calculation of open_flags by open(2) arguments into new helper
in fs/open.c, move filp_open() over there, have it and do_sys_open()
use that helper, switch exec.c callers of do_filp_open() to explicit
(and constant) struct open_flags.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
instead of ad-hackery around need_reval_dot(), do the following:
set a flag (LOOKUP_JUMPED) in the beginning of path, on absolute
symlink traversal, on ".." and on procfs-style symlinks. Clear on
normal components, leave unchanged on ".". Non-nested callers of
link_path_walk() call handle_reval_path(), which checks that flag
is set and that fs does want the final revalidate thing, then does
->d_revalidate(). In link_path_walk() all the return_reval stuff
is gone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
all remaining callers pass LOOKUP_PARENT to it, so
flags argument can die; renamed to kern_path_parent()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
As per SAT-3 the WWN ID should be included in the VPD page 0x83
(device identification) emulation.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some DMA controllers (eg: drivers/dma/dw_dmac*) allow platform specific
configuration for dma transfers. User drivers need to set chan->private field
of channel with pointer to configuration data. This patch takes dma_priv data
from platform data and passes it to chan->private_data, in order to pass
platform specific configuration to DMAC controller.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The Arasan CompactFlash Device Controller has three basic modes of
operation: PC card ATA using I/O mode, PC card ATA using memory mode, PC card
ATA using true IDE modes.
Currently driver supports only True IDE mode.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds ata_sff_queue_work() & ata_sff_queue_delayed_work() routine in
libata-sff.c file. This routine can be used by ata drivers to use ata_sff_wq.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds the struct xfrm_replay_state_esn which will be
used to support IPsec extended sequence numbers and anti replay windows
bigger than 32 packets. Also we add a function that returns the actual
size of the xfrm_replay_state_esn, a xfrm netlink atribute and a xfrm state
flag for the use of extended sequence numbers.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the Mult and bMaxBurst values from the endpoint companion
descriptor to calculate the max length of an isoc transfer.
Add USB_SS_MULT macro to access Mult field of bmAttributes, at
Sarah's suggestion.
This patch should be queued for the 2.6.36 and 2.6.37 stable trees, since
those were the first kernels to have isochronous support for SuperSpeed
devices.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
USB_PORT_STAT_SUPER_SPEED is a made up symbol that the USB core used to
track whether USB ports had a SuperSpeed device attached. This is a
linux-internal symbol that was used when SuperSpeed and non-SuperSpeed
devices would show up under the same xHCI roothub. This particular
port status is never returned by external USB 3.0 hubs. (Instead they
have a USB_PORT_STAT_SPEED_5GBPS that uses a completely different speed
mask.)
Now that the xHCI driver registers two roothubs, USB 3.0 devices will only
show up under USB 3.0 hubs. Rip out USB_PORT_STAT_SUPER_SPEED and replace
it with calls to hub_is_superspeed().
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Introduce the notion of a PCI device that may be associated with more than
one USB host controller driver (struct usb_hcd). This patch is the start
of the work to separate the xHCI host controller into two roothubs: a USB
3.0 roothub with SuperSpeed-only ports, and a USB 2.0 roothub with
HS/FS/LS ports.
One usb_hcd structure is designated to be the "primary HCD", and a pointer
is added to the usb_hcd structure to keep track of that. A new function
call, usb_hcd_is_primary_hcd() is added to check whether the USB hcd is
marked as the primary HCD (or if it is not part of a roothub pair). To
allow the USB core and xHCI driver to access either roothub in a pair, a
"shared_hcd" pointer is added to the usb_hcd structure.
Add a new function, usb_create_shared_hcd(), that does roothub allocation
for paired roothubs. It will act just like usb_create_hcd() did if the
primary_hcd pointer argument is NULL. If it is passed a non-NULL
primary_hcd pointer, it sets usb_hcd->shared_hcd and usb_hcd->primary_hcd
fields. It will also skip the bandwidth_mutex allocation, and set the
secondary hcd's bandwidth_mutex pointer to the primary HCD's mutex.
IRQs are only allocated once for the primary roothub.
Introduce a new usb_hcd driver flag that indicates the host controller
driver wants to create two roothubs. If the HCD_SHARED flag is set, then
the USB core PCI probe methods will allocate a second roothub, and make
sure that second roothub gets freed during rmmod and in initialization
error paths.
When usb_hc_died() is called with the primary HCD, make sure that any
roothubs that share that host controller are also marked as being dead.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The xHCI driver essentially has both a USB 2.0 and a USB 3.0 roothub. So
setting the HCD_USB3 bits in the hcd->driver->flags is a bit misleading.
Add a new field to usb_hcd, bcdUSB. Store the result of
hcd->driver->flags & HCD_MASK in it. Later, when we have the xHCI driver
register the two roothubs, we'll set the usb_hcd->bcdUSB field to HCD_USB2
for the USB 2.0 roothub, and HCD_USB3 for the USB 3.0 roothub.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Change the bandwith_mutex in struct usb_hcd to a pointer. This will allow
the pointer to be shared across usb_hcds for the upcoming work to split
the xHCI driver roothub into a USB 2.0/1.1 and a USB 3.0 bus.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Update the USB core to deal with USB 3.0 hubs. These hubs have a slightly
different hub descriptor than USB 2.0 hubs, with a fixed (rather than
variable length) size. Change the USB core's hub descriptor to have a
union for the last fields that differ. Change the host controller drivers
that access those last fields (DeviceRemovable and PortPowerCtrlMask) to
use the union.
Translate the new version of the hub port status field into the old
version that khubd understands. (Note: we need to fix it to translate the
roothub's port status once we stop converting it to USB 2.0 hub status
internally.)
Add new code to handle link state change status. Send out new control
messages that are needed for USB 3.0 hubs, like Set Hub Depth.
This patch is a modified version of the original patch submitted by John
Youn. It's updated to reflect the removal of the "bitmap" #define, and
change the hub descriptor accesses of a couple new host controller
drivers.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Using a #define to redefine a common variable name is a bad thing,
especially when the #define is in a header. include/linux/usb/hcd.h
redefined bitmap to DeviceRemovable to avoid typing a long field in the
hub descriptor. This has unintended side effects for files like
drivers/usb/core/devio.c that include that file, since another header
included after hcd.h has different variables named bitmap.
Remove the bitmap #define and replace instances of it in the host
controller code. Cleanup the spaces around function calls and square
brackets while we're at it.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Cc: Max Vozeler <mvz@vozeler.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Cc: Olav Kongas <ok@artecdesign.ee>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Renames items that are improperly labelled as "network scope" items
(which are represented by simple integer values) rather than "network
domain" items (which are represented by <Z.C.N>-type network addresses).
This change is purely cosmetic, and does not affect the operation of TIPC.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Gets rid of the need for users to specify the maximum number of
cluster nodes supported by TIPC. TIPC now automatically provides
support for all 4K nodes allowed by its addressing scheme.
Note: This change sets TIPC's memory usage to the amount used by
a maximum size node table with 4K entries. An upcoming patch that
converts the node table from a linear array to a hash table will
compact the node table to a more efficient design, but for clarity
it is nice to have all the Kconfig infrastruture go away separately.
Signed-off-by: Allan Stephens <Allan.Stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
On suspend we disable all interrupts in the core code, but this does
not mask the interrupt line in the default implementation as we use a
lazy disable approach. That means we mark the interrupt disabled, but
leave the hardware unmasked. That's an optimization because we avoid
the hardware access for the common case where no interrupt happens
after we marked it disabled. If an interrupt happens, then the
interrupt flow handler masks the line at the hardware level and marks
it pending.
Suspend makes use of this delayed disable as it "disables" all
interrupts when preparing the suspend transition. Right before the
system goes into hardware suspend state it checks whether one of the
interrupts which is marked as a wakeup interrupt came in after
disabling it.
Most interrupt chips have a separate register which selects the
interrupts which can wake up the system from suspend, so we don't have
to mask any on the non wakeup interrupts.
But now we have to deal with brilliant designed hardware which lacks
such a wakeup configuration facility. For such hardware it's necessary
to mask all non wakeup interrupts before going into suspend in order
to avoid the wakeup from random interrupts.
Rather than working around this in the affected interrupt chip
implementations we can solve this elegant in the core code itself.
Add a flag IRQCHIP_MASK_ON_SUSPEND which can be set by the irq chip
implementation to indicate, that the interrupts which are not selected
as wakeup sources must be masked in the suspend path. Mask them in the
loop which checks the wakeup interrupts pending flag.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
LKML-Reference: <alpine.LFD.2.00.1103112112310.2787@localhost6.localdomain6>
mpc23s17 is very similar to the mcp23s08, except that registers are 16bit
wide, so extend the interface to work with both variants.
The s17 variant also has an additional address pin, so adjust platform
data structure to support up to 8 devices per SPI chipselect.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.
The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new behaviour is enabled using the new module parameter
'nfs4_disable_idmapping'.
Note that if the server rejects an unmapped uid or gid, then
the client will automatically switch back to using the idmapper.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This will make it possible to clear the lseg pointer in the same
function as it is put, instead of in the caller nfs_pageio_doio().
Signed-off-by: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Allows the pnfs filelayout driver to write to the data servers.
Note that COMMIT to data servers will be implemented in a future
patch. To avoid improper behavior, for the moment any WRITE to a data
server that would also require a COMMIT to the data server is sent
NFS_FILE_SYNC.
Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: Dean Hildebrand <dhildeb@us.ibm.com>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Mingyang Guo <guomingyang@nrchpc.ac.cn>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Ricardo Labiaga <Ricardo.Labiaga@netapp.com>
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We grab the lseg sent in from the doio function and attach it to
each struct nfs_write_data created. This is how the lseg will be
sent to the layout driver.
Signed-off-by: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add callback that pnfs layout driver can use to do its own handling
of data server WRITE response.
Signed-off-by: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
No need for generic cache with only one user.
Keep a simple hash of deviceids in the filelayout driver.
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Acked-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Use our own async error handler.
Mark the layout as failed and retry i/o through the MDS on specified errors.
Update the mds_offset in nfs_readpage_retry so that a failed short-read retry
to a DS gets correctly resent through the MDS.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Attempt a pNFS file layout read by setting up the nfs_read_data struct and
calling nfs_initiate_read with the data server rpc client and the
filelayout rpc call ops.
Error handling is implemented in a subsequent patch.
Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: Dean Hildebrand <dhildeb@us.ibm.com>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Mingyang Guo <guomingyang@nrchpc.ac.cn>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Ricardo Labiaga <Ricardo.Labiaga@netapp.com>
Tested-by: Guo Mingyang <guomingyang@nrchpc.ac.cn>
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Introduce a data server set_client and init session following the
nfs4_set_client and nfs4_init_session convention.
Once a new nfs_client is on the nfs_client_list, the nfs_client cl_cons_state
serializes access to creating an nfs_client struct with matching properties.
Use the new nfs_get_client() that initializes new clients.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
