Avoid to mismatch between NR_BUILTIN_GPIO and gpio interrupt number.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Avoid to mismatch between NR_BUILTIN_GPIO and GPIO interrupt number
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The irq_set_wake() function of the gpio irq_chip calls
enable/disable_irq_wake() on the demultiplex interrupt. That leads to
a lockdep warning "INFO: possible recursive locking detected" because
irq_set_type() is called under irq_desc->lock and the *_irq_wake()
calls take irq_desc->lock of the demux interrupt.
Tell lockdep that the gpio irqs are in a different lock class.
Documentation/SubmitChecklist:
15: All codepaths have been exercised with all lockdep features enabled.
That's a non-optional requirement, AFAICT.
Reported-and-tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LAKML-Reference: alpine.LFD.2.00.1104041416290.19945@localhost6.localdomain6
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Directives such as .long and .word do not magically cause the
assembler location counter to become aligned in gas. As a
result, using these directives in code sections can result in
misaligned data words when building a Thumb-2 kernel
(CONFIG_THUMB2_KERNEL).
This is a Bad Thing, since the ABI permits the compiler to
assume that fundamental types of word size or above are word-
aligned when accessing them from C. If the data is not really
word-aligned, this can cause impaired performance and stray
alignment faults in some circumstances.
In general, the following rules should be applied when using
data word declaration directives inside code sections:
* .quad and .double:
.align 3
* .long, .word, .single, .float:
.align (or .align 2)
* .short:
No explicit alignment required, since Thumb-2
instructions are always 2 or 4 bytes in size.
immediately after an instruction.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
LAKML-Reference: 1289913217-8672-1-git-send-email-dave.martin@linaro.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For the lcdif clock get_rate looks as follows:
read div from HW_CLKCTRL_DIS_LCDIF.DIV
return clk_get_rate(clk->parent) / div
with clk->parent being ref_pix_clk on my system.
ref_pix_clk's rate depends on HW_CLKCTRL_FRAC1.PIXFRAC.
The set_rate function for lcdif does:
parent_rate = clk_get_rate(clk->parent);
based on that calculate frac and div such that
parent_rate * 18 / frac / div is near the requested rate.
HW_CLKCTRL_FRAC1.PIXFRAC is updated with frac
HW_CLKCTRL_DIS_LCDIF.DIV is updated with div
For this calculation to be correct parent_rate needs to be
initialized not with the clock rate of lcdif's parent (i.e. ref_pix) but
that of its grandparent (i.e. ref_pix' parent == pll0_clk).
The obvious downside of this patch is that now set_rate(lcdif) changes
its parent's rate, too. Still this is better than a wrong rate.
Acked-by: Shawn Guo <shawn.guo@freescale.com>
LAKML-Reference: 20110225084950.GA13684@S2101-09.ap.freescale.net
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This was broken by
4bd597b (ARM i.MX ehci: do ehci init in board specific functions)
and fixes:
CC arch/arm/mach-mx3/mach-vpr200.o
arch/arm/mach-mx3/mach-vpr200.c:263: error: unknown field 'flags' specified in initializer
arch/arm/mach-mx3/mach-vpr200.c:264: warning: initialization makes pointer from integer without a cast
by just applying the change to mach-vpr200.c that the other machine files
got by 4bd597b.
LAKML-Reference: 1302257029-17397-1-git-send-email-u.kleine-koenig@pengutronix.de
Acked-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The patch below removes an unused config variable found by using a kernel
cleanup script.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VFP registers d16-d31 are callee saved registers and must be preserved
during function calls, including fork(). The VFP configuration should
also be preserved. The patch copies the full VFP state to the child
process.
Reported-by: Paul Wright <paul.wright@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds THREAD_NOTIFY_COPY for calling registered handlers
during the copy_thread() function call. It also changes the VFP handler
to use a switch statement rather than if..else and ignore this event.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The HIGHPTE config option depends on !OUTER_CACHE. However, there is no
set_pte_ext() function that does outer cache maintenance by physical
address, hence no need for such restriction.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit a737823d ("ARM: perf: ensure overflows aren't missed due to IRQ
latency") changed the way that event deltas are calculated on overflow
so that we don't miss events when the new count value overtakes the
previous one.
Unfortunately, we forget to count the event that passes through zero so
we end up being off by 1. This patch adds on the correction.
Reported-by: Chris Moore <moore@free.fr>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DBGVCR, used for configuring vector catch debug events, is UNKNOWN
out of reset on ARMv7. When enabling monitor mode, this must be zeroed
to avoid UNPREDICTABLE behaviour.
This patch adds the zeroing code to the debug reset path.
Cc: stable <stable@kernel.org>
Reported-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: arch-shmobile: only run FSI init on respective boards
ARM: arch-shmobile: only run HDMI init on respective boards
ARM: mach-shmobile: Correctly check for CONFIG_MACH_MACKEREL
If several boards are enabled in the kernel configuration,
fsi_init_pm_clock() functions from board-ap4evb.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If several boards are enabled in the kernel configuration,
hdmi_init_pm_clock() functions from board-ap4evb.c and board-mackerel.c
will run on any of them. Prevent this by calling these functions from the
.init_machine() callback instead of using device_initcall().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I made a bit of a thinko when adding Mackerel to the boards
that support zboot using MMCIF.
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Offering CONFIG_PM_SLEEP for CPUs which do not support suspend leads to
build errors, so only set CONFIG_ARCH_SUSPEND_POSSIBLE if we have a CPU
selected which supports suspend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CONFIG_PM is now set whenever we support either runtime PM in addition
to suspend and hibernate. This causes build errors when runtime PM is
enabled on a platform, but the CPU does not have the appropriate support
for suspend.
So, switch this code to use CONFIG_PM_SLEEP rather than CONFIG_PM to
allow runtime PM to be enabled without causing build errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Checking 'rate < 0' doesn't work because 'rate' is unsigned.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Colin Cross <ccross@android.com>
Change af90f10d38 "ARM: 6759/1: smp: Select local timers vs broadcast
timer support runtime" missed a return statement, causing a compile
warning:
arch/arm/mach-msm/timer.c:272: warning: 'return' with no value, in
function returning non-void
Trivially return 0 for success when running on cpu 0 (to match the
comment and previous behavior).
Signed-off-by: David Brown <davidb@codeaurora.org>
The qsd8x50 board file contains a few references to machine_is_...
macros that are otherwise unused, and contain no machine definition.
The recent purge of unused machine definitions breaks the compilation
of this target.
Since the machine cannot ever be used, just remove the bogus checks.
Signed-off-by: David Brown <davidb@codeaurora.org>
Change b0f18edaf6
(arm: tegra: Remove unused bogus irq enable/disable magic)
introduces warnings:
arch/arm/mach-tegra/gpio.c: In function 'tegra_gpio_resume':
arch/arm/mach-tegra/gpio.c:260: warning: unused variable 'i'
arch/arm/mach-tegra/gpio.c: In function 'tegra_gpio_suspend':
arch/arm/mach-tegra/gpio.c:283: warning: unused variable 'i'
Fix them, and fix a coding style issue on the same lines.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Erik Gilling <konkers@konkers.net>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
avr32: Fix missing irq namespace conversion
powerpc: qe_ic: Rename get_irq_desc_data and get_irq_desc_chip
genirq: Remove the now obsolete config options and select statements
arm: versatile : Fix typo introduced in irq namespace cleanup
sound: Fixup the last user of the old irq functions
genirq: Remove obsolete comment
genirq: Remove now obsolete set_irq_wake()
sh: Fix irq cleanup fallout
x86: apb_timer: Fixup genirq fallout
genirq: Fix misnamed label in handle_edge_eoi_irq
Fix up crazy conflict in arch/powerpc/include/asm/qe_ic.h:
- commit eead4d5c63 ("powerpc: qe_ic: Rename get_irq_desc_data and
get_irq_desc_chip") made the helper functions use
irq_desc_get_handler_data() instead of the legacy (and no longer
existing) get_irq_desc_data.
- commit d4db35e8dc ("powerpc/qe_ic: Fix another breakage from the
irq_data conversion") used irq_desc_get_chip_data() instead.
According to Thomas, the former is the correct direct conversion, but it
does look like both should work (arch/powerpc/sysdev/qe_lib/qe_ic.c
seems to initialize both to the same thing), and the chip data in some
ways is the more logical. Somebody should really decide on one of the
other.
This merge picks irq_desc_get_handler_data() as the straightforward pure
conversion to new names, as per Thomas.
Commit 6845664(arm: Cleanup the irq namespace) introduces a typo
causing a build failure for the versatile platform.
[ tglx: Sorry, my bad. Have no idea how I fatfingered that ]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
LKML-Reference: <20110330060229.27397.7628.stgit@ponder>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
Reorder
irq_set_chip()
irq_set_chip_data()
irq_set_handler()
to
irq_set_chip()
irq_set_handler()
irq_set_chip_data()
so the next patch can combine irq_set_chip() and irq_set_handler() to
irq_set_chip_and_handler().
Automated conversion with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Avoid the whole lazy disable dance in the demux handler by providing a
irq_disable() callback.
Use the proper accessor functions and tidy up gpio_irq_handler()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make use of the new functionality which ensures that irq_set_type is
called with the chip masked. Unmask is only done when the interrupt is
not disabled.
Retrieve the trigger type from irq_data in unmask
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use the proper accessor function instead of fiddling in the status
bits directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Remove the open coded access to irq_desc which will fail on sparse irq
and use the proper wrappers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
