In OMAP4, as per new PM programming model, the legacy registers
which were there in OMAP3 are all shifted by 0x100 while new one's
are added from offset 0 to 0x10.
For OMAP4, the register offset appending of 0x100 done in devices.c
currently, is moved to driver file.This change fits in for current
implementation as well as once the driver undergoes hwmod adaptation.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap4 es2 hsmmc has a updated soft reset logic.After the
reset is issued monitor a 0->1 transition first. The reset of
CMD or DATA lines is complete only after a 0->1->0 transition
of SRC or SRD bits.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The existing definitions for cpu revision used
upper nibble in the bits[15:08]. With OMAP3630,
definitions use lower nibble.
This patch unifies the definitions to start
at lower nibble.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: McBSP: tx_irq_completion used in rx_irq_handler
omap: Fix compile dependency to LEDS_CLASS
This patch adds driver support for OMAP2/3/4 high speed UART.
The driver is made separate from 8250 driver as we cannot
over load 8250 driver with omap platform specific configuration for
features like DMA, it makes easier to implement features like DMA and
hardware flow control and software flow control configuration with
this driver as required for the omap-platform.
This patch involves only the core driver and its dependent.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove set_uart_globals function as this will not be needed as
physical address for uarts will be taken from hwmod data file.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds omap_hwmod data for UARTs on OMAP2 and OMAP3
platforms.
UART4 support for 3630 and OMAP2 hwmod data added by Govindraj R.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch splits omap_init_wdt() into separate omap_init_wdt()
functions under mach-omap1 and mach-omap2 and set them up with
subsys_initcall.
Also it uses omap_device_build() API instead of
platform_device_register() for watchdog timer device registration
for OMAP2plus chips.
For OMAP2plus chips, the device specific data defined in centralized
hwmod database will be used.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Introduce of a generic way to setup smsc911x based Ethernet
controller connected to GPMC similar to gpmc-smc91x but without
timing setup.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding support for LogicPD's OMAP 3530 LV SOM and
OMAP 35x Torpedo board.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch has multiple fixes together. To ensure that git bisect work across
commits, all changes are clubbed together
1. Move the common control base address to control core
2. Remove the manually coeded defines and use the ones from headers.
3. Fix the the status register define in id.c for OMAP4
4. Fix all the register define in hsmmc.c
5. Use the control pad accessor API for omap4 hsmmc register accesses
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4, control module is divided into 4 separate IPs
- OMAP44XX_CTRL_MODULE_CORE
- OMAP44XX_CTRL_MODULE_PAD_CORE
- OMAP44XX_CTRL_MODULE_WKUP
- OMAP44XX_CTRL_MODULE_PAD_WKUP
This patch adds all the omap4 control module register data and
includes them in the common control.h
The register data is autogenerated from the codebase thanks
to Benoit Cousson efforts
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 control pad are not addressable from control
core base. So the common omap_ctrl_read/write APIs breaks
Hence export separate APIs to manage the omap4 pad control
registers.
This APIs will work only for OMAP4
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On omap4 control module is divided in four IP blocks.
- CTRL_MODULE_CORE 0x4a002000
- CTRL_MODULE_PAD_CORE 0x4a100000
- CTRL_MODULE_WKUP 0x4a30c000
- CTRL_MODULE_PAD_WKUP 0x4a31e000
Addressing all the modules with single base address is not possible
considering 16 bit offsets. The mux code manages the pad core and pad
wakeup related base address inside the mux framework. For other usage
only control core and control pad bases are necessary. So this patch
maps only needed pad control base address which is used by device drivers
and infrastructure code
The main control core base is still kept same in this patch to
keep git-bisect working. This will be fixed in the relevant patch
in this series.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DSS on ES2 supports only OSWR, hence remove the support
for CSWR from the powerdomain framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
update OMAP Kconfig help texts for all supported SoC models
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP SRG (Sample Rate Generator) and FSG (Frame Sync
Generator) is only needed to be enabled, when McBSP
is master.
In McBSP slave mode, the SRG, and FSG can be kept disabled,
which might save some power at the end in this configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix this and similar build warnings when building with
omap_4430sdp_defconfig.
CC arch/arm/mach-omap2/board-4430sdp.o
In file included from arch/arm/mach-omap2/board-4430sdp.c:36:
arch/arm/plat-omap/include/plat/usb.h:109: warning: return type defaults to 'int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently we map 1 MB section while setting up SRAM on OMAPs
Regardless of the actual memory. The physical OCM RAM available
on OMAP SOCs is in order of KBs. This patch maps only available
sram and cleans up some un-necessary cpu_is_xxx checks.
Mapping un-available or non-accessible(secure) memory on the newer ARM
processor is dangerous. Because ARM CPUs can now speculatively prefetch,
we should avoid mapping any no-existing or secure memory.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently there is a bug in the existing omap_device core code when
extracting the hwmod structures passed to omap_device_build_ss(). This bug
gets exposed only when passing multiple hwmod structures to
omap_device_build_ss() resulting in incorrect extraction from second hwmod
structure.
This fix uses the pointer to pointer to omap_hwmod structure (array of
pointers to omap_hwmod structure) passed to omap_device_build_ss() to
correctly extract the appropriate omap_hwmod structure.
This patch has been created and tested on lo/master and mainline.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Charulatha V <charu@ti.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
This patch is temporary fix to below crash. This is observed when
CPU is clocked more than 600 MHz.
Unhandled fault: imprecise external abort (0x1406) at 0xbf9ef65c
Internal error: : 1406 [#1] PREEMPT SMP
last sysfs file:
Modules linked in:
CPU: 0 Not tainted (2.6.36-rc3+ #18)
PC is at kernel_thread_helper+0x0/0x14
LR is at kernel_thread_helper+0x0/0x14
pc : [<c003ce14>] lr : [<c003ce14>] psr: 00000093
sp : dc83bff8 ip : 00000000 fp : 00000000
r10: 00000000 r9 : 00000000 r8 : 00000000
r7 : 00000013 r6 : c003ce28 r5 : c008935c r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : 00000000
Flags: nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7f Table: 8000404a DAC: 00000017
Process swapper (pid: 2, stack limit = 0xdc83a2f0)
Stack: (0xdc83bff8 to 0xdc83c000)
bfe0: 00000000 ffffffff
[<c003ce14>] (kernel_thread_helper+0x0/0x14) from [<fffffffe>] (0xfffffffe)
Code: c03a0ba3 c03a5fcb c045c880 c0394035 (eb017701)
---[ end trace 1b75b31a2719ed1c ]---
The timer hwmod adaptation will eventually fix it in a proper way.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch updates the id.c and cpu.h files to support
omap4 ES2.0 silicon detection. Few initial omap4 es2 samples
IDCODE is same as es1. So the patch uses ARM cpuid register to
detect the ES version for such samples
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
On OMAP4 there is no need to have SRAM_BOOTLOADER_SZ provision
Hence put this macro under CONFIG_ARCH_OMAP2PLUS check
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For OMAP24xx/34xx/44xx: omap_type() returns the correct type:
OMAP2_DEVICE_TYPE_TEST
OMAP2_DEVICE_TYPE_EMU
OMAP2_DEVICE_TYPE_SEC
OMAP2_DEVICE_TYPE_GP
OMAP2_DEVICE_TYPE_BAD
In current implementation there are two problems:
Problem 1:
For 34xx, the current if check will never return true.
Problem 2:
For 24xx the correct type check should be with omap_type() function
Verified by checking the TRM 24xx for CONTROL_STATUS register bits
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Looks like a typo from commit d6d834b010.
Signed-off-by: Scott Ellis <scott@jumpnowtek.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes these compiler warnings:
CC arch/arm/mach-omap2/mux.o
arch/arm/mach-omap2/mux.c: In function 'omap_mux_init_gpio':
arch/arm/mach-omap2/mux.c:90: warning: 'gpio_mux' may be used uninitial
ized in this function
CC arch/arm/plat-omap/gpio.o
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_resume_after_idle':
arch/arm/plat-omap/gpio.c:2152: warning: 'l' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_prepare_for_idle':
arch/arm/plat-omap/gpio.c:2085: warning: 'l2' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c:2085: warning: 'l1' may be used uninitialized
in this function
CC arch/arm/mach-omap2/board-omap4panda.o
arch/arm/mach-omap2/board-omap4panda.c: In function 'omap4_panda_init':
arch/arm/mach-omap2/board-omap4panda.c:277: warning: unused variable 's
tatus'
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If a GPIO bank has more than one GPIO with debounce enabled, the
debounce clock will not be fully disabled before going to
idle/suspend.
In the idle path, we just do a single clk_disable() of the bank's
debounce clock. If there are multiple debounce-enabled GPIOs in the
bank, that clocks usage count will be > 1, so the clk_disable() will
not actually disable the clock.
So the fix is to clk_disable() for every debounce-enabled GPIO in the
bank (and an equivalent clk_enable() of course.)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The current version contains only the interconnects and the
mpu hwmods.
The remaining hwmods will be introduced by further patches on
top of this one.
- enable as well omap_hwmod.c build for OMAP4 Soc
Please not that this file uses the new naming convention for
naming HW IPs. This convention will be backported soon for previous
OMAP2 & 3 data files.
new name trm name
------------- -------------------
counter_32k synctimer_32k
l3_main l3
timerX gptimerX / dmtimerX
mmcX mmchsX / sdmmcX
dma_system sdma
smartreflex_X sr_X / sr?
usb_host_fs usbfshost
usb_otg_hs hsusbotg
usb_tll_hs usbtllhs_config
wd_timerX wdtimerX
ipu cortexm3 / ducati
dsp c6x / tesla
iva ivahd / iva2.2
kbd kbdocp / keyboard
mailbox system_mailbox
mpu cortexa9 / chiron
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In order to help differentiate omap_devices from normal
platform_devices, make them all a parent of a new common parent
device.
Then, in order to determine if a platform_device is also an
omap_device, checking the parent is all that is needed.
Users of this feature are the runtime PM core for OMAP, where we need
to know if a device being passed in is an omap_device or not in order
to know whether to call the omap_device API with it.
In addition, all omap_devices will now show up under /sys/devices/omap
instead of /sys/devices/platform
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This reverts commit 0007122ad8.
The dereference method of checking for a valid omap_device when
wrapping a platform_device is rather unsafe and dangerous.
Instead, a better way of checking for a valid omap-device is
to use a common parent device for all omap_devices, then a check
can simply be made using the device parent. The only user of this
API was the initial version of the runtime PM core for OMAP. This
has now been switched to check device parent, so there are no more
users of this API.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 has an iva device and a dsp devcice where as OMAP2/3
has only an iva device. In this file the iva device in the
system is registered under the name dsp_dev and the API
to retrieve the iva device is omap2_get_dsp_device.
This patch renames the dsp_dev to iva_dev, renames
omap2_get_dsp_device to omap2_get_iva_device,
registers dsp_dev for OMAP4 and adds a new API
omap4_get_dsp_device to retrieve the dep_dev.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch:
- adds more documentation to the hwmod code
- fixes some documentation typos elsewhere in the file
- changes the _sysc_*() function names to appear in (verb, noun) order,
to match the rest of the function names.
This patch should not result in any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
For every optional clock present per hwmod per omap-device, this function
adds an entry in the clocks list of the form <dev-id=dev_name, con-id=role>,
if an entry is already present in the list of the form <dev-id=NULL, con-id=role>.
The function is called from within the framework inside omap_device_build_ss(),
after omap_device_register.
This allows drivers to get a pointer to its optional clocks based on its role
by calling clk_get(<dev*>, <role>).
Link to discussions related to this patch:
http://www.spinics.net/lists/linux-omap/msg34809.html
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: simplified loop iterator; removed the superfluous clk_get(),
using the clk_get() in clk_add_alias() instead]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Some modules (like GPIO, DSS...) require optionals clock to be enabled
in order to complete the sofreset properly.
Add a HWMOD_CONTROL_OPT_CLKS_IN_RESET flag to force all optional clocks
to be enabled before reset. Disabled them once the reset is done.
TODO:
For the moment it is very hard to understand from the HW spec, which
optional clock is needed and which one is not. So the current approach
will enable all the optional clocks.
Paul proposed a much finer approach that will allow to tag only the needed
clock in the optional clock table. This might be doable as soon as we have
a clear understanding of these dependencies.
Reported-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
In OMAP3 a specific SYSSTATUS register was used to get the softreset status.
Starting in OMAP4, some IPs does not have SYSSTATUS register and instead
use the SYSC softreset bit to provide the status.
Other cases might exist:
- Some IPs like McBSP does have a softreset control but no reset status.
- Some IPs that represent subsystem, like the DSS, can contains
a reset status without softreset control. The status is the aggregation
of all the sub modules reset status.
- Add a new flag (SYSC_HAS_RESET_STATUS) to identify the new programming model
and replace the previous SYSS_MISSING, that was used to flag IP with
softreset control but without the SYSSTATUS register, with a specific
SYSS_HAS_RESET_STATUS flag.
- MCSPI and MMC contains both programming models, so the legacy one
will be prevented by removing the syss offset field that become useless.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Expose an hardreset API from hwmod in order to assert / deassert all the
individual reset lines that belong to an hwmod. This API is needed by
some of the more complicated processor drivers, e.g., DSP/Bridge,
Syslink, etc.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Most processor IPs does have a hardreset signal controlled by the PRM.
This is different of the softreset used for local IP reset from the
SYSCONFIG register.
The granularity can be much finer than orginal HWMOD, for ex, the IVA
hwmod contains 3 reset lines, the IPU 3 as well, the DSP 2...
Since this granularity is needed by the driver, we have to ensure
than one hwmod exist for each hardreset line.
- Store reset lines as hwmod resources that a driver can query by name like
an irq or sdma line.
- Add two functions for asserting / deasserting reset lines in hwmods
processor that require manual reset control.
- Add one functions to get the current reset state.
- If an hwmod contains only one line, an automatic assertion / de-assertion
is done.
-> de-assert the hardreset line only during enable from disable transition
-> assert the hardreset line only during shutdown
Note: The hwmods with hardreset line and HWMOD_INIT_NO_RESET flag must be
kept in INITIALIZED state.
They can be properly enabled only if the hardreset line is de-asserted
before.
For information here is the list of IPs with HW reset control
on an OMAP4430 device:
RM_DSP_RSTCTRL
1,1,'RST2','RW','1','DSP - MMU, cache and slave interface reset control'
0,0,'RST1','RW','1','DSP - DSP reset control'
RM_IVA_RSTCTRL
2,2,'RST3','RW','1','IVA logic and SL2 reset control'
1,1,'RST2','RW','1','IVA Sequencer2 reset control'
0,0,'RST1','RW','1','IVA sequencer1 reset control'
RM_IPU_RSTCTRL
2,2,'RST3','RW','1','IPU MMU and CACHE interface reset control.'
1,1,'RST2','RW','1','IPU Cortex M3 CPU2 reset control.'
0,0,'RST1','RW','1','IPU Cortex M3 CPU1 reset control.'
PRM_RSTCTRL
1,1,'RST_GLOBAL_COLD_SW','RW','0','Global COLD software reset control.'
0,0,'RST_GLOBAL_WARM_SW','RW','0','Global WARM software reset control.'
RM_CPU0_CPU0_RSTCTRL
RM_CPU1_CPU1_RSTCTRL
0,0,'RST','RW','0','Cortex A9 CPU0&1 warm local reset control'
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: made the hardreset functions static; moved the register
twiddling into prm*.c functions in previous patches; changed the
function names to conform with hwmod practice]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Since OMAP4 is using an absolute address, the current PRM accessors
are not useable.
OMAP4 adaptation for these API are currently ongoing, so define temp
version until the proper ones are defined.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently omap_hwmod_mutex is being used to protect both the list
access/modification and concurrent access to hwmod functions. This
patch separates these two types of locking.
First, omap_hwmod_mutex is used only to protect access and
modification of omap_hwmod_list. Also cleaned up some comments
referring to this mutex that are no longer needed.
Then, for protecting concurrent access to hwmod functions, use a
per-hwmod mutex. This protects concurrent access to a single hwmod,
but would allow concurrent access to different hwmods.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: added structure documentation; changed mutex variable
name]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The dma request line attribute was named dma channel, which leads
to confusion with the real dma channel definition.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
