Add a node for the ir receiver found on the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Added a node label]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add an ir_clk sub-node to the prcm node.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Only SPI0 is enabled, as the schematic denotes it as the only SPI bus,
while other pins are reserved for different peripherals.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These are based on the available SPI configurations of Cubieboard,
Olimex LIME, and PcDuino. There is no pin group for SPI3, as all the
boards seem to use those pins for EMAC.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Hummingbird A31 board, the RTL8211E ethernet phy has its reset
line connect to a gpio pin, instead of floating like on other boards.
Add the stmmac properties for describing the reset gpio.
The reset delays were taken from the RTL8211E datasheet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add pinmux settings for the ir receive pin of the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. This can be avoided by letting the display frontend engine
do the dma from memory, and then letting it feed the data directly into
the backend unmodified, as the frontend does have deep enough fifo-s.
Note since u-boot-v2015.01 has been released using the de_be0-lcd0-hdmi
pipeline on sun4i, we need to keep that one around too (unfortunately).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It was accidentally left (& copied & pasted all around) from our
experiments with gpio-keys-polled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Luxul XWC-1000 is a controller device based on BCM4708 SoC. The only
unusual thing in its DTS file is "ubi" partition on NAND flash.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These add device tree entry for qspi device on dra72-evm.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Seems to be a left-over from an automatic merge.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On Vybrid, all peripherals are numbered starting with zero,
including the GPIO and PORT module. However, the labels of the
corresponding device tree nodes start with one, which is confusing.
Fix that by renaming the labels of the gpio nodes in the device
tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently PWM functionality is broken on mx25 due to the wrong assignment of the
PWM "per" clock.
According to Documentation/devicetree/bindings/clock/imx25-clock.txt:
pwm_ipg_per 52
,so update the pwm "per" to use 'pwm_ipg_per' instead of 'per10' clock.
With this change PWM can work fine on mx25.
Cc: <stable@vger.kernel.org>
Reported-by: Carlos Soto <csotoalonso@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* Tidy up #sound-dai-cells settings
* Drop "renesas,rcar_sound" compatible value
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VWG8
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-cleanups2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Cleanups for v3.20" from Simon
Horman:
Second Round of Renesas ARM Based SoC DT Cleanups for v3.20
* Tidy up #sound-dai-cells settings
* Drop "renesas,rcar_sound" compatible value
* tag 'renesas-dt-cleanups2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7790: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7791 dtsi: Drop "renesas,rcar_sound" compatible value
ARM: shmobile: r8a7790 dtsi: Drop "renesas,rcar_sound" compatible value
Signed-off-by: Olof Johansson <olof@lixom.net>
The file is roughly sorted alphabetically (with some exceptions where
old options have been split in two), so alphascale should go at the
top instead of at the bottom.
Also linewrap like other entries have been lately.
Signed-off-by: Olof Johansson <olof@lixom.net>
for now it is wary basic SoC description with most important IPs needed
to make this device work
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
The legacy interrupts on omap4 got broken when gic got changed to
use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We
still have the hardcoded legacy IRQ numbers in use in several places,
most notably the in the legacy DMA. It took a while to figure out
what the problem was and how it should be fixed for the -rc series.
Also include is a regression fix for the dra7 dwc3 suspend.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lpO3
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Urgent omap4 legacy interrupt regression fix for v3.19-rc series" from
Tony Lindgren:
A rather urgent pull request to fix omap4 legacy interrupts.
The legacy interrupts on omap4 got broken when gic got changed to
use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We
still have the hardcoded legacy IRQ numbers in use in several places,
most notably the in the legacy DMA. It took a while to figure out
what the problem was and how it should be fixed for the -rc series.
Also include is a regression fix for the dra7 dwc3 suspend.
* tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Work around hardcoded interrupts
arm: boot: dts: dra7: enable dwc3 suspend PHY quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
The commit (3d125f9c91) cause i.MX6SX sdb enet cannot work. The cause is
the commit add mdio node with un-correct phy address.
The patch just correct i.MX6sx sdb board enet phy address.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows booting the device with basic functionality.
Note that at least on my revision c board the DDR3 does
not seem to work properly and only some of the memory
can be reliably used.
Also, the mainline u-boot does not seem to properly
initialize the ethernet, so I've been using the old TI
u-boot at:
http://arago-project.org/git/projects/?p=u-boot-omap3.git;a=summary
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clocks on dm816x are a bit different from the other omap
variants. The clocks are sourced from a FAPLL (Flying Adder PLL)
unlike on other omaps. Other than that, it's a similar setup
to am33xx with extra muxes and dividers that can be defined
as existing component clocks.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to other omap variants, let's add dm816x support.
Note that this is based on generated data from the
TI81XX-LINUX-PSP-04.04.00.02 patches published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
I've verified the basic functionality, but have not been
able to test all the devices on dm8168-evm.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- little typo and a LED declared
- addition of the Special Function Registers (SFR) + its binding
- RTC & SRAM nodes
- the at91sam9xe has its own .dtsi now. Not combined with at91sam9260 anymore
- addition of the Image Sensor Interface (ISI) DT part and supported sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUt+9WAAoJEAf03oE53VmQrlQH/2gLux3w9NMBm6GKDAJe3ZbY
JSiT9JIpcDmvVPXheeXQc0gZFGbfg8kcbx6mopPR/n6gAeP0npRApmQxS04M9M6b
HyAyj26s1h79WZOki7hhsIw6bhMCNDb7ODoDOw4F6U1/WWLh+uZY3fg+HO2CFBS8
wyDWKQQWAe0LvbaB44iw5cGsZ2+8/1rb5R7w7AqITjLTOGLvJZn50TYlY6hRrb+7
qfD0gqaRzX6axdtsGVNzkuYUuLQ3rE9IhgauhHlge9QT1Lkl4wfONnGiOFeIc+n0
tcHLb3BYBqOKDbOop+3ED3bqxcmobUIQIlEutvg5lnFkWeVYnXgkIFxHPpEK4K0=
=RH2X
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "at91: dt for 3.20 #1" from Nicolas Ferre:
First batch of DT changes for 3.20:
- little typo and a LED declared
- addition of the Special Function Registers (SFR) + its binding
- RTC & SRAM nodes
- the at91sam9xe has its own .dtsi now. Not combined with at91sam9260 anymore
- addition of the Image Sensor Interface (ISI) DT part and supported sensors
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: dts: sama5d3: add ov2640 camera sensor support
ARM: at91: dts: sama5d3: change name of pinctrl of ISI_MCK
ARM: at91: dts: sama5d3: change name of pinctrl_isi_{power,reset}
ARM: at91: dts: sama5d3: move the isi mck pin to mb
ARM: at91: dts: sama5d3: add missing pins of isi
ARM: at91: dts: sama5d3: split isi pinctrl
ARM: at91: dts: sama5d3: add isi clock
ARM: at91/dt: ethernut5: use at91sam9xe.dtsi
ARM: at91/dt: Add a dtsi for at91sam9xe
ARM: at91/dt: add SRAM nodes
ARM: at91/dt: at91rm9200ek: enable RTC
ARM: at91/dt: rm9200: add RTC node
ARM: at91/dt: at91sam9n12: Add RTC node
ARM: at91: sama5d4: Add SFR
ARM: at91: sama5d3: Add SFR
ARM: at91: Add Special Function Registers binding documentation
ARM: at91/dt: sam9263: Fix typo: ac91_clk -> ac97_clk
ARM: at91/dt: sama5d3: enable D2 as the heartbeat LED
Signed-off-by: Olof Johansson <olof@lixom.net>
CSR Marco SoC has never shipped to customers that could be interested
in mainline support. and new Atlas7 is a replacement SoC that is in
development.
so we drop Marco dts stuff, and add dts stuff for Atlas7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wbyB
-----END PGP SIGNATURE-----
Merge tag 'atlas7-init-dts-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux into next/dt
Merge "CSR atlas7 init dts for 3.20" from Barry Song:
Drop Marco and add init dts stuff for Atlas7
CSR Marco SoC has never shipped to customers that could be interested
in mainline support. and new Atlas7 is a replacement SoC that is in
development.
So we drop Marco dts stuff, and add dts stuff for Atlas7.
* tag 'atlas7-init-dts-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux:
ARM: dts: add init dts file for CSR atlas7 SoC
ARM: dts: drop MARCO platform DT stuff
Signed-off-by: Olof Johansson <olof@lixom.net>
The interrupt is 16, not 32 (which it would be if we include PPIs
in the count of interrupts).
Cc: Andy Gross <agross@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Tested-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This changes muxes in gpio26 pin to function as gpio and adds support
for sd card detect for apq8064 based IFC6410 board.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
We've been sitting on our fixes branch for a while, so this batch is
unfortunately on the large side.
A lot of these are tweaks and fixes to device trees, fixing various bugs
around clocks, reg ranges, etc. There's also a few defconfig updates
(which are on the late side, no more of those).
All in all the diffstat is bigger than ideal at this time, but the nothing
in here seems particularly risky.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lJPi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on our fixes branch for a while, so this batch is
unfortunately on the large side.
A lot of these are tweaks and fixes to device trees, fixing various
bugs around clocks, reg ranges, etc. There's also a few defconfig
updates (which are on the late side, no more of those).
All in all the diffstat is bigger than ideal at this time, but nothing
in here seems particularly risky"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
reset: sunxi: fix spinlock initialization
ARM: dts: disable CCI on exynos5420 based arndale-octa
drivers: bus: check cci device tree node status
ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288
ARM: nomadik: fix up leftover device tree pins
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
ARM: exynos_defconfig: Enable LM90 driver
ARM: exynos_defconfig: Enable options for display panel support
arm: dts: Use pmu_system_controller phandle for dp phy
ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
...
The arndale-octa board was giving "imprecise external aborts" during
boot-up with MCPM enabled. CCI enablement of the boot cluster was found
to be the cause of these aborts (possibly because the secure f/w was not
allowing it). Hence, disable CCI for the arndale-octa board.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "at91: fixes for 3.19 #1 (ter)" from Nicolas Ferre:
First fixes batch for AT91 on 3.19:
- fix some DT entries
- correct clock entry for the at91sam9263 LCD
- add a phy_fixup for Eth1 on sama5d4
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: berlin: Fixes for v3.19 (round 1)" from Sebastian Hesselbarth:
Marvell Berlin fixes for v3.19 round 1:
- SDHCI DT fixes for BG2Q and BG2Q reference board
- BG2Q SM GPIO DT node relocation
* tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
Signed-off-by: Olof Johansson <olof@lixom.net>
We altered the device tree bindings for the Nomadik family of
pin controllers to be standard, this file was merged out-of-order
so we missed fixing this. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "omap fixes against v3.19-rc1" from Tony Lindgren:
Fixes for omaps mostly to deal with dra7 timer issues
and hypervisor mode. The other fixes are minor fixes for
various boards. The summary of the fixes is:
- Fix real-time counter rate typos for some frequencies
- Fix counter frequency drift for am572x
- Fix booting of secondary CPU in HYP mode
- Fix n900 board name for legacy user space
- Fix cpufreq in omap2plus_defconfig after Kconfig change
- Fix dra7 qspi partitions
And also, let's re-enable smc91x on some n900 boards that
we have sitting in a few test boot systems after the boot
loader dependencies got fixed.
* tag 'omap-for-v3.19/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
ARM: OMAP2+: Fix n900 board name for legacy user space
ARM: omap5/dra7xx: Enable booting secondary CPU in HYP mode
ARM: dra7xx: Fix counter frequency drift for AM572x errata i856
ARM: omap5/dra7xx: Fix frequency typos
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: fixes for 3.19" from Shawn Guo:
The i.MX fixes for 3.19:
- One fix for incorrect i.MX25 SPI1 clock assignment in device tree,
which causes system hang when accessing SPI1.
- Correct i.MX6SX QSPI parent clock configuration to fix a kernel Oops.
- Fix ULPI PHY reset modelling on imx51-babbage board to remove the
dependency on bootloader for USB3317 ULPI PHY reset.
- Correct video divider setting on i.MX6Q rev T0 1.0 to fix the issue
that HDMI is not working at high resolution on T0 1.0.
- One incremental fix for CODA960 VPU enabling in device tree to
correct interrupt order.
- LS1021A SCFG block works in BE mode, add device tree property
big-endian to make it right.
* tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: imx6sx: Set PLL2 as parent of QSPI clocks
ARM: dts: imx25: Fix the SPI1 clocks
ARM: clk-imx6q: fix video divider for rev T0 1.0
ARM: dts: imx6qdl: Fix CODA960 interrupt order
ARM: ls1021a: dtsi: add 'big-endian' property for scfg node
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: rockchip: dts fix for 3.19" from Heiko Stübner:
Increase drive-strength to sdmmc pins on rk3288-evb to fix
an issue with the fixed highspeed card detection.
* tag 'v3.19-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: bump sd card pin drive strength up on rk3288-evb
Signed-off-by: Olof Johansson <olof@lixom.net>
There is an external resistor divider on PB16, acting like a pull-down,
the pull-up increase power consumption and prevent the vbus detect pin
to reach Vss voltage, ~1.5V mesured on my board, it might not even work
if the pull-up is stronger than usual.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds device tree nodes for L2 cache controller present on
Exynos4 SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MiPHY28lp is a Generic PHY which can serve various SATA, PCIe or
USB3 devices. The two first ports can be use for either; both SATA, both
PCIe or one of each in any configuration.
The Third port is only for USB3.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
B2199 HDK is the reference board for STiH418 SoC.
It has the following characteristics:
- 3GB DDR3
- 8GB eMMC / SD-Card slot
- 32MB NOR Flash
- 1 x Gbit Ethernet
- 1 x USB3.0 port
- 2 x USB2.0 ports
- 1 x Sata or Mini-PCIe port
- 1 x WiFi 802.11ac (Quantenna)
- 1 x HDMI out
- 1 x HDMI in
- 1 x SPDIF
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The STiH418 is advanced UHD 60fps AVC processor with 3D graphic acceleration and
quad-core ARM Cortex A9 CPU.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the DRM/KMS dt nodes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the DRM/KMS dt nodes.
This node can't be in stih407-family.dtsi file because in the future we
will integrate a new stih418-b2199 board. It's a stih407 family board
with different drm/kms dt nodes.
That is why i created the stih407.dtsi file.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Whenever Suspend PHY bit is set on DRA7x devices,
USB will not work due to Set EP Configuration command
always failing.
This was only found after a recent commit 2164a47 (usb:
dwc3: set SUSPHY bit for all cores, which will be merged
for v3.19) added a missing *required* step to dwc3
initialization. Synopsys Databook requires that we enable
Suspend PHY bit after initialization but that, unfortunately,
breaks DRA7x.
Note that the same regression was already patched for AM437x.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to v4l2 dt document, we add:
a camera host: ISI port.
a i2c camera sensor: ov2640 port.
to sama5d3xmb.dtsi.
The ov2640 node defines the pinctrls, clocks and refer to isi port.
The ISI node also has a reference to the ov2640 port.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For sama5d3xmb board, the pins: pinctrl_isi_pck_as_mck is pck1, and
used to provide MCK for camera sensor.
We change its name to: pinctrl_pck1_as_isi_mck.
As we want camera sensor instead of ISI to configure the pck1 (ISI_MCK) pin.
So we remove this pinctrl from ISI DT node. It will be added in sensor's
DT node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For sama5d3xmb board, the pins: pinctrl_isi_{power,reset} is used to
power-down or reset camera sensor.
So we should let camera sensor instead of ISI to configure the pins.
This patch will change pinctrl name from pinctrl_isi_{power,reset} to
pinctrl_sensor_{power,reset}. And remove these two pinctrl from ISI's
DT node. We will add these two pinctrl to sensor's DT node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
