Reduces the likelihood of false pulse detects in the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM contains scale factors for the tx power, which define
the range of allowable difference between target power and training
power. If the difference is too big, PA predistortion cannot be used.
For 2.4 GHz there is only one scale factor, for 5 GHz there are
three, depending on the specific frequency range.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM PAPRD rate mask fields only contain mask values for actual
rates in the low 25 bits. The upper bits are reserved for tx power
scale values. Add the proper mask definitions and use them before
writing the values to the register.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be able to measure the thermal values correctly for PAPRD, we need
to send training frames before setting up the gain table for the measurement,
and then again afterwards for the actual training.
For further improvement, send training frames at MCS0 instead of 54 MBit/s
legacy. That way we can use the No-ACK flag for the transmission, which
speeds up PAPRD training in general, as the hardware won't have to
retransmit and wait for ACK timeout (was previously set to 4 * 6
transmission attempts).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Testing shows that adjusting the slot time based on the coverage class
produces very high latencies and very low throughput on long distance links.
Adjusting only the ACK timeout and leaving the slot time at the regular
values - while technically not optimal for CSMA - works a lot better on
long links (tested with 10 km distance)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(u32) -1 is not particularly useful as a slottime default, so even though
the ath9k_hw default should never get used, it's better to pick something
sane here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to have separate callbacks for pre-AR9003 vs AR9003
SREV version checks, so just merge those into one function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9280 based hardware with 3 antennas and slow antenna diversity has
not been seen in the wild and ath9k does not support that form of
antenna diversity, so remove the EEPROM ops for it.
These EEPROM ops are currently only used for setting the
AR_PHY_SWITCH_COM register, which is being done in the EEPROM specific
file already.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a comment about a potential array overrun that needs to
be reviewed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer chips do not need this, and maybe these register writes could have
negative side effects on newer hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless-testing commit 04caf86375
('ath9k: more tx setup cleanups') merged tx path code for HT vs
non-HT frames, however it did not pass the tid pointer to
ath_tx_send_normal, causing an inconsistency between AMPDU vs
non-AMPDU sequence number handling.
Fix this by always passing in the tid pointer for all QoS data frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be awake when accessing registers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed we do not know band width at core reset time and it is not a good
idea to reset whole just to change band. So just set unconditionally 20 MHz
band width as default during core reset.
As for defines PHY clock changed to band width in specs and it makes much more
sens to call defines by band width which is self-explainable. Updated specs do
not mention 0 value, but comparing to old ones you can notice lineral relation
between PHY clock speed and band width. So it makes sense for 0x0 value to be
10 MHz band width.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.
Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers TBTT_TIMER ,DMA_BEACON_ALERT ,NEXT_SWBA are need to be
configured only for AP and IBSS mode.
SWBA register is used for generating software interrupts so that beacon
frames will be created by the software.DMA beacon alert register is
to indicate the hardware to DMA the contents of beacon buffer to PCU buffer
and TBTT to start transmitting the packet buffer to the base band.
Clearly these things are not needed for station/monitor mode so
remove configuring them.
Cc: doug dahlby <ddahlby@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
key4 of micentry is used, if ATH_CRYPT_CAP_MIC_COMBINED is set.
But is not cleared on key cache reset.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to change interface type
without bringing down the interface.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 will notify drivers when to go idle and ath9k
assumed that it would get further notifications for idle
states after a device stop() config call but as per agreed
semantics the idle state of the radio is left up to driver
after mac80211 issues the stop() callback. The driver is
resposnbile for ensuring the device remains idle after
that even between suspend / resume calls.
This fixes suspend/resume when you issue suspend and resume
twice on ath9k when ath9k_stop() was already called. We need
to put the radio to full sleep in order for resume to work
correctly.
What might seem fishy is we are turning the radio off
after resume. The reason why we do this is because we know
we should not have anything enabled after a mac80211 tells
us to stop(), if we resume and never get a start() we won't
get another stop() by mac80211 so to be safe always bring
the 802.11 device with the radio disabled after resume,
this ensures that if we suspend we already have the radio
disabled and only a start() will ever trigger it on.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon a failure we never call ath9k_ps_restore() on ath_radio_enable(),
this will throw off the sc->ps_usecount. When the sc->ps_usecount
is > 0 we never put the chip to full sleep. This drains battery,
and will also make the chip fail upon resume with:
ath: Starting driver with initial channel: 5745 MHz
ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
This would make the chip useless upon resume.
I cannot prove this can happen but in theory it is so best to
avoid this race completely and not have users complain about
a broken device after resume.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code wants to check if there's a channel and it is not disabled,
but it used to check if channel is not NULL and accessed the channel
struct if this check failed.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ehea_error, ehea_info and ehea_debug macros.
Use pr_fmt, pr_<level>, netdev_<level> and netif_<level> as appropriate.
Fix messages to use trailing "\n", some messages had an extra one
as the old ehea_<level> macros added a trailing "\n".
Coalesced long format strings.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always go through a new ip4_dst_hoplimit() helper, just like ipv6.
This allowed several simplifications:
1) The interim dst_metric_hoplimit() can go as it's no longer
userd.
2) The sysctl_ip_default_ttl entry no longer needs to use
ipv4_doint_and_flush, since the sysctl is not cached in
routing cache metrics any longer.
3) ipv4_doint_and_flush no longer needs to be exported and
therefore can be marked static.
When ipv4_doint_and_flush_strategy was removed some time ago,
the external declaration in ip.h was mistakenly left around
so kill that off too.
We have to move the sysctl_ip_default_ttl declaration into
ipv4's route cache definition header net/route.h, because
currently net/ip.h (where the declaration lives now) has
a back dependency on net/route.h
Signed-off-by: David S. Miller <davem@davemloft.net>
__pppoe_xmit function return value was invalid resulting in
additional call to kfree_skb on already freed skb. This resulted in
memory corruption and consequent kernel panic after PPPoE peer
terminated the link.
This fixes commit 55c95e738d.
Reported-by: Gorik Van Steenberge <gvs@zemos.net>
Reported-by: Daniel Kenzelmann <kernel.bugzilla@kenzelmann.dyndns.info>
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Reported-by: Pawel Staszewski <pstaszewski@artcom.pl>
Diagnosed-by: Andrej Ota <andrej@ota.si>
Diagnosed-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Tested-by: Pawel Staszewski <pstaszewski@artcom.pl>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Andrej Ota <andrej@ota.si>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must not wake the TX queue without free TX descriptors.
sca_xmit() expects at least one free descriptor and BUGs otherwise.
Problem reported and fix tested by Bernie Innocenti and Ward Vandewege.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_src_init_t2() is used only when BCM_CNIC is defined.
So, to avoid a compilation warning, we won't define it unless
BCM_CNIC is defined.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the LSO code work on BE platforms: parsing_data field of
a parsing BD (PBD) for 57712 was improperly composed which made FW read wrong
values for TCP header's length and offset and, as a result, the corresponding
PCI device was performing bad DMA reads triggering EEH.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing usage of rtnl_lock() to protect firmware interface registers.
These registers are accessed in some worker threads and can create a
deadlock if rtnl_lock is taken by upper layers while the worker is still
pending.
We remove rtnl_lock and use a driver mutex just while mailboxes are
accessed.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_scheduled_work() is on its way out. Drop flush_scheduled_work()
from prism2_free_local_data() and replace it with explicit flushing of
work items on the respective free functions. Work items in ap_data
are flushed from hostap_free_data() and the ones in local_info from
prism2_free_local_data().
Flush is used instead of cancel as some process and free items from
queue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: netdev@vger.kernel.org
i2400m implements dynamic work allocation and queueing mechanism in
i2400_schedule_work(); however, this is only used for reset and
recovery which can be served equally well with preallocated per device
works.
Replace i2400m_schedule_work() with two work structs in struct i2400m.
These works are explicitly canceled when the device is released making
calls to flush_scheduled_work(), which is being deprecated,
unnecessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: linux-wimax@intel.com
Cc: netdev@vger.kernel.org
gp->reset_task_pending is always set right before reset_task is
scheduled and as there is no synchronization between the setting and
scheduling, busy looping on reset_task_pending before flushing
reset_task doesn't really buy anything.
Directly flush gp->reset_task on suspend and cancel on detach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
All three drivers use flush_scheduled_work() similarly during driver
detach. Replace it with explicit cancels.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
flush_scheduled_work() is on its way out. Remove its usage from
iseries_veth.
* Cancelling a delayed work, queueing it for immediate execution if
cancelled and then waiting for completion can be done by simply
calling flush_delayed_work_sync().
* Explicitly cancel cnx->statemachine_wq on module unload.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Santiago Leon <santil@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
Directly cancel port->reset_task from ehea_shutdown_single_port()
instead. As this cancels the work for each port on driver detach,
flushing system_wq from ehea_remove() or ehea_module_exit() is no
longer necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
ehea_rereg_mr_task is not used. Remove it and drop @work parameter
from ehea_rereg_mrs().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
flush_scheduled_work() is on its way out. This patch contains simple
conversions to replace flush_scheduled_work() usage with direct
cancels and flushes.
Directly cancel the used works on driver detach and flush them in
other cases.
The conversions are mostly straight forward and the only dangers are,
* Forgetting to cancel/flush one or more used works.
* Cancelling when a work should be flushed (ie. the work must be
executed once scheduled whether the driver is detaching or not).
I've gone over the changes multiple times but it would be much
appreciated if you can review with the above points in mind.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: netdev@vger.kernel.org
janz-ican3, sh_eth, skge and vxge don't use workqueue at all and there
is no reason to flush the system_wq. Drop flush_scheduled_work()
calls and references to workqueue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Sivakumar Subramani <sivakumar.subramani@exar.com>
Cc: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Cc: Jon Mason <jon.mason@exar.com>
Cc: netdev@vger.kernel.org
The driver global au_macs[] is unused in the entire kernel tree,
so remove it.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
