Add and initialize the gpio_wp and gpio_cd members. We need to
ensure that all users are covered, because GPIO 0 may be valid.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Attepmpt to configure ULPI pins gives the following compile error:
CC arch/arm/mach-pxa/cm-x300.o
arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_AF0' undeclared here (not in a function)
arch/arm/mach-pxa/cm-x300.c:155: error: 'MFP_MFP_DS01X' undeclared here (not in a function)
make[2]: *** [arch/arm/mach-pxa/cm-x300.o] Error 1
make[1]: *** [arch/arm/mach-pxa] Error 2
make: *** [sub-make] Error 2
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Document the layout of our swp PTE entries, adding definitions for
the bit masks/shifts/sizes, and implement MAX_SWAPFILES_CHECK()
such that we fail to build if we are unable to properly encode the
swp type field.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now required for libsas:
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Building modules, stage 2.
MODPOST 1096 modules
ERROR: "xscale_flush_kern_dcache_page" [drivers/scsi/libsas/libsas.ko] undefined!
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull linus#master to merge PER_CPU_DEF_ATTRIBUTES and alpha build fix
changes. As alpha in percpu tree uses 'weak' attribute instead of
inline assembly, there's no need for __used attribute.
Conflicts:
arch/alpha/include/asm/percpu.h
arch/mn10300/kernel/vmlinux.lds.S
include/linux/percpu-defs.h
As slab is available early now, use kzalloc() rather than
alloc_bootmem_low() in pxa_init_gpio_chip().
This removes the following boot time warning:
<4>------------[ cut here ]------------
<4>WARNING: at mm/bootmem.c:535 alloc_arch_preferred_bootmem+0x2c/0x54()
<d>Modules linked in:
[<c0029430>] (unwind_backtrace+0x0/0xdc) from [<c0036f64>] (warn_slowpath_common+0x4c/0x80)
[<c0036f64>] (warn_slowpath_common+0x4c/0x80) from [<c000ede0>] (alloc_arch_preferred_bootmem+0x2c/0x54)
[<c000ede0>] (alloc_arch_preferred_bootmem+0x2c/0x54) from [<c000f2e4>] (___alloc_bootmem_nopanic+0x34/0xd0)
[<c000f2e4>] (___alloc_bootmem_nopanic+0x34/0xd0) from [<c000f6e4>] (___alloc_bootmem+0xc/0x34)
[<c000f6e4>] (___alloc_bootmem+0xc/0x34) from [<c000cb20>] (pxa_init_gpio+0x48/0x228)
[<c000cb20>] (pxa_init_gpio+0x48/0x228) from [<c0009794>] (init_IRQ+0x34/0x44)
[<c0009794>] (init_IRQ+0x34/0x44) from [<c00089d4>] (start_kernel+0x144/0x264)
[<c00089d4>] (start_kernel+0x144/0x264) from [<a0008034>] (0xa0008034)
<4>---[ end trace 1b75b31a2719ed1c ]---
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In commit f23d491131, the pwr-i2c device name changed due to the
newly introduced device table. This patch fixes the clock so the
driver's probe will succeed again.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The default configuration file for the KwikByte kb9202 board was based on a 2.6.13-rc2 kernel and doesn't produce a bootable kernel. Update the
configuration in order to produce a bootable image.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the basic infrastructure for the Nomadik 8815
CPU and the "Nomadik Hardware Kit" NHK8815. This patch only
includes the serial console and core stuff, no drivers.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PrimeCell Vectored Interrupt Controller offers a way to trigger
any interrupt through software. This is a useful tool for developing,
but such software interrupt can only be acked by writing a bit in the
"software clear" register, or the handler will loop forever. This
splits ack from mask, and acks the soft irq in case it was the source.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Nomadik SoC (not yet merged) has a modified PL090 VIC cell. This adds
support for it by reading the PrimeCell ID at the end of the page and
calling a separate init function.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds a few default locks to the clocks (the clocks were used
before the locks were initialized by code), then renames the clocks
a bit to fit with the latest driver names (some changed during
review). Lastly it moves the initialization of the clock debugfs
entry to module_init() initcall level since the debugfs isn't up
in core_initcall().
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This defconfig update selects all the new U300 drivers merged for
2.6.31-rc1 in the merge window and add defaults for the new
config options. It compiles and boots nicely from initramfs on
the U300.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Hong Xu <hong.xu@atmel.com>
Here are the modification to at91sam9261 files dedicated to the support of
at91sam9g10. This direction has been adopted to minimize code duplication.
All at91sam9261 drivers are enabled in _devices and board- files. Modificaton
to peripherals that support at91sam9g10 will be added in future patches.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Hong Xu <hong.xu@atmel.com>
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Here is the basic header file support for this product.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Hong Xu <hong.xu@atmel.com>
Add the at91sam9g10 support to the AT91 generic clock file. It takes
advantage of the management by functionalities of those PLLs and clocks.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds input keyboard gpio support on at91sam9g20ek board.
It adds button 3 and 4.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here are the at91 specific files dedicated to the at91sam9g45 series. They
mimic the traditional at91 way of managing chips & boards.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES. In
the future, the main board for this 9g45 series will be the
AT91SAM9M10G45-EK (I choose this last name for the board file).
Simple drivers are enabled in _devices and board- files. Newer peripheral
support will be added in future patches.
Incuded peripherals support (for now):
- USART
- SPI
- Ethernet
- NAND flash
- LCD
- gpio/joystick/buttons
- leds and pwm
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embedds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
Here is the basic header file support for this product series.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the at91sam9g45 series support to the AT91 generic clock file.
This takes care of the particularities of the PMC for this series.
It also takes advantage of the management by functionalities of
those PLLs and clocks.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove at91_gpiolib_request. It returns -EPERM if a request pin is not
in GPIO mode, however we want to be able to gpio_request alternative
function pins to reserve them, and in some cases we need to be able to
use the gpiolib functions on alternative function pins.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds input keyboard gpio support on at91sam9rlek board. It adds button 1
and 2 (left and right click).
It also adds gpio leds ds1, ds2 and ds3.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here is a little update to the at91sam9rlek lcd interface.
This will correct the power pin of the LCD.
It will also add precision to the struct atmel_lcdfb_info
scructure: backlight enabling and wiring mode correction:
RGB wiring on the -EK board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ep93xx: Show gpio interrupt type in debugfs output.
EP93xx uses a private implementation for the debugfs output.
Modify this output so it includes the interrupt type when the
gpio is configured as an interrupt
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix ep93xx gpio.c header includes and __iomem pointers.
1. <linux/gpio.h> should be included instead of <asm/gpio.h>
2. <mach/hardware.h> should be included instead of <mach/ep93xx-regs.h>
3. data_reg and data_dir_reg in struct ep93xx_gpio_chip should be
void __iomem pointers not unsigned int
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: ep93xx: ensure typesafe io
For the ep93xx platform, all EP93XX_*_BASE defines are based
on virtual addresses. Ensure that all these defines are
properly typesafe for the __raw_{read/write}* macros.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the link script for ARM to use PAGE_SIZE instead of hard-
coded 4096. Also the old RODATA macro is deprecated
for the RO_DATA(PAGE_SIZE) macro. As a consequence the PAGE_SIZE
was changed from (1UL << PAGE_SHIFT) to (_AC(1,UL) << PAGE_SHIFT)
because the linker does not understand the "UL" suffix to numeric
constants.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
handle_bad_irq() expects the IRQ number to be valid (used for statistics),
so it cannot be called with an illegal vector. The problem was reported
by a static analysis tool.
The change makes bad_irq_desc redundant, so delete it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
x86 throws away .discard section but no other archs do. Also,
.discard is not thrown away while linking modules. Make every arch
and module linking throw it away. This will be used to define dummy
variables for percpu declarations and definitions.
This patch is based on Ivan Kokshaysky's alpha percpu patch.
[ Impact: always throw away everything in .discard ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
This patch fixes two errors we get when building GTA02 kernel.
~ use_bbt is incorrect, we need flash_bbt.
~ We do not need .force_soft_ecc because we can unset
CONFIG_MTD_NAND_S3C2410_HWECC.
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: updated patch description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The commit 9db41f9edc added
the .flash_bbt flag to the nand set, so add this back into
the mach-mini2440.c file (taken out on initial commit to
allow build).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 52da219e96 added IIS
platform devices, but these do not build on s3c24xx systems
and the file depends on SND_S3C24XX_SOC, which is selected
for all S3C64XX/S3C24XX systems.
As a quick fix, make the dev-audio.o file depends on
SND_S3C64XX_SOC_I2S instead.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 52da219e96 removed
the s3c_device_iis, but didn't replace it with anything
so a number of s3c24xx machines are currently failing
to build.
As a temporary fix, re-instate s3c_device_iis until a
proper replacement can be done for it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The commit ec976d6eb0
removed a number of gpio definitions from <mach/hardware.h>
but misssed updating these two files:
Fix the following build errors by including <linux/gpio.h>:
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c: In function 's3c24xx_spi_gpiocfg_bus1_gpg5_6_7':
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c: In function 's3c24xx_spi_gpiocfg_bus0_gpe11_12_13':
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The "EET" variant of the pcm037 board has an OLED display, using a S6E63D6
display controller on the first SPI interface, using GPIO57 as a chip-select
for it. S6E63D6 is initialised in the boot-loader, so we only have to take care
of the LCD. EET also adds several buttons and LEDs on GPIOs. This patch adds a
"pcm037_variant=" kernel command line parameter to specify at boot-time which
board the kernel is running on, default is "pcm970", specify "eet" for the EET
board.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
