Since we keep the clock value linearly continuous on frequency change,
make sure the initial multiplier is 0, such that our initial value is 0.
Without this we compute the initial value at whatever the TSC has
managed to reach since power-on.
Reported-and-Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Fixes: 20d1c86a57 ("sched/clock, x86: Rewrite cyc2ns() to avoid the need to disable IRQs")
Cc: lenb@kernel.org
Cc: rjw@rjwysocki.net
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: rui.zhang@intel.com
Cc: jacob.jun.pan@linux.intel.com
Cc: Mike Galbraith <bitbucket@online.de>
Cc: hpa@zytor.com
Cc: paulmck@linux.vnet.ibm.com
Cc: John Stultz <john.stultz@linaro.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: dyoung@redhat.com
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140123094804.GP30183@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The code would assume sched_clock_stable() and switch to !stable
later, this switch brings a discontinuity in time.
The discontinuity on switching from stable to unstable was always
present, but previously we would set stable/unstable before
initializing TSC and usually stick to the one we start out with.
So the static_key bits brought an extra switch where there previously
wasn't one.
Things are further complicated by the fact that we cannot use
static_key as early as we usually call set_sched_clock_stable().
Fix things by tracking the stable state in a regular variable and only
set the static_key to the right state on sched_clock_init(), which is
ran right after late_time_init->tsc_init().
Before this we would not be using the TSC anyway.
Reported-and-Tested-by: Sasha Levin <sasha.levin@oracle.com>
Reported-by: dyoung@redhat.com
Fixes: 35af99e646 ("sched/clock, x86: Use a static_key for sched_clock_stable")
Cc: jacob.jun.pan@linux.intel.com
Cc: Mike Galbraith <bitbucket@online.de>
Cc: hpa@zytor.com
Cc: paulmck@linux.vnet.ibm.com
Cc: John Stultz <john.stultz@linaro.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: lenb@kernel.org
Cc: rjw@rjwysocki.net
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: rui.zhang@intel.com
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140122115918.GG3694@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The #ifdef CONFIG_PREEMPT is both not needed and wrong.
Its not required because asm/preempt.h should provide
{set,clear}_preempt_need_resched() regardless and its wrong because
for voluntary preempt we still rely on PREEMPT_NEED_RESCHED.
Reported-and-Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Fixes: 8cb75e0c4e ("sched/preempt: Fix up missed PREEMPT_NEED_RESCHED folding")
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20140122102435.GH31570@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This reverts commit 282cf499f0.
With the current implementation, the load average statistics of a sched entity
change according to other activity on the CPU even if this activity is done
between the running window of the sched entity and have no influence on the
running duration of the task.
When a task wakes up on the same CPU, we currently update last_runnable_update
with the return of __synchronize_entity_decay without updating the
runnable_avg_sum and runnable_avg_period accordingly. In fact, we have to sync
the load_contrib of the se with the rq's blocked_load_contrib before removing
it from the latter (with __synchronize_entity_decay) but we must keep
last_runnable_update unchanged for updating runnable_avg_sum/period during the
next update_entity_load_avg.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Ben Segall <bsegall@google.com>
Cc: pjt@google.com
Cc: alex.shi@linaro.org
Link: http://lkml.kernel.org/r/1390376734-6800-1-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Export the symbol so that it is accessible to modules. Fixes the
following error:
ERROR: "wm5100_detect" [sound/soc/samsung/snd-soc-lowland.ko] undefined!
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Input GPIO changes can generate interrupts, but we need kind of ACK for
them by changing IRQ polarity. This is required to stop hardware from
keep generating interrupts and generate another one on the next GPIO
state change.
This code allows using GPIOs with standard interrupts and add for
example GPIO buttons support.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6216/
The file uses u16 type but doesn't include its definition explicitly
I was getting this error when including this header in my driver:
arch/mips/include/asm/mipsregs.h:644:33: error: unknown type name ‘u16’
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: Steven J. Hill <Steven.Hill@imgtec.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6212/
we want the device tree to be unflattened into non init memory so it can be
accessed later by, for example, a probing function of a driver module.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6210/
The defaults are not always applicable and it makes it hard for the bootloader
to override them. By removing it we give the bootloader full control over what
command line parameters to pass.
Without this change we will need to modify the built-in dtb to add bootloader
cmd line parameters or do some work to append them after we unflatten the device
tree.
Sead3 is a development board, that's why we want to be able to change boot
parameters on the fly from the bootloader.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6208/
if the user sets memsize parameter in commandline or bootloader
environment, we use it to modify the built-in dtb memory size
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6207/
Update the early_printk code to include linux/serial_bcm63xx.h which
provides the definitions for the UART block registers. While at it,
remove the inclusion of serial_bcm63xx.h which was just there to allow
smooth transition.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6203/
Now that the UART block defines have been moved to a separate file,
include that one and do not longer rely on the MIPS-specific
bcm63xx_regs.h header file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6204/
Move the BCM63XX UART driver definitions to
include/linux/serial_bcm63xx.h such that we do not rely on the MIPS
BCM63XX code to provide these for us.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6202/
bcm_{readl,writel} macros expand to __raw_{readl,writel}, use these
directly such that we do not rely on the platform to provide these for
us. As a result, we no longer use bcm63xx_io.h, so remove that inclusion
too.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6201/
bcm63xx_irqs.h is included but we are not using anything from it, drop
that include.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6205/
Remove usage of -mno-jals compiler flag when building a pure
microMIPS kernel. The -mno-jals flag only ever existed within
Mentor toolchains. Dropping this flag allows all FSF toolchains
to work.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6200/
This will be needed by the next patch to use said nodes for probing
via the device tree.
Signed-off-by: David Daney <david.daney@cavium.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6185/
This patch switches Malta from using the MIPS implementation of early
printk with Malta's prom_putchar to using the generic 8250_early
implementation. This offers a couple of advantages:
- We duplicate less generic code.
- The UART can be initialised rather than being reliant upon
inheriting a valid setup from the bootloader.
The Malta console_config function is extended to initialise the early
console if no earlycon= kernel parameter is provided, inheriting the
modetty0 bootloader environment if present and falling back to a
default 38400n8r setup if not. This matches the behaviour used for the
regular console= parameter.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6183/
This patch causes the kernel to mux the SERIRQ interrupt to the SERIRQ
pin of the PIIX4 and to enable that interrupt. The kernel depends upon
the interrupt when using the SuperIO UARTs (ttyS0 & ttyS1) but
previously would not configure it, instead relying upon the bootloader
having done so. If that is not the case then the typical result is that
the system appears to hang once it reaches userland as no output is
displayed on the UART.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6182/
The RTC is used on Malta to estimate the clock frequency of the CPU &
optionally the GIC. However the kernel previously did not initialise the
RTC, instead relying upon the bootloader having done so. In order to
minimise dependencies which the kernel has upon the bootloader this
patch causes the kernel to initialise the RTC itself prior to making use
of it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6184/
This variable seems to have been copied from Malta when SEAD3 support
was introduced, but is likewise unused. Remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6172/
This variable was introduced by commit 96348c8f (of Ralf's historic
Linux/MIPS repository) "Remaining fixes for MIPS's eval boards." but
I don't see any use of it either then or now. Remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6171/
Export symbols needed by the octeon-ethernet driver. The patch fixes a
build failure with CONFIG_OCTEON_ETHERNET=m.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6166/
The following build error is seen if CONFIG_32BIT is undefined,
CONFIG_64BIT is defined, and CONFIG_MIPS32_O32 is undefined.
asm/syscall.h: In function 'mips_get_syscall_arg':
arch/mips/include/asm/syscall.h:32:16: error: unused variable 'usp' [-Werror=unused-variable]
cc1: all warnings being treated as errors
Fixes: c0ff3c53d4 ('MIPS: Enable HAVE_ARCH_TRACEHOOK')
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6160/
The boot hangs early on EBH5600 board when octeon_fdt_pip_iface() is
trying enumerate a non-existant interface. The actual hang happens in
cvmx_helper_interface_get_mode():
mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
when interface == 4. We can avoid this situation by first checking that
the interface exists in the DTB.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6101/
When booting with in-kernel DTBs, the pruning code will enumerate
interfaces 0-4. However, there is memory reserved only for 4 so some
other data will get overwritten by cvmx_helper_interface_enumerate().
Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6102/
'lay' is not very meaningful, so use it 'layer' instead to let the dev_info()
clearer.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add new definitions for hotplug live status bits for VLV2 since they're
in reverse order from the gen4x ones.
Changelog:
- Restored gen4 bit definitions
- Added new definitions for VLV2
- Added platform check for IS_VALLEYVIEW() in dp_detect to use the correct
bit defintions
- Replaced a lost trailing brace for the added switch()
Signed-off-by: Todd Previte <tprevite@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73951
[danvet: Switch to _VLV postfix instead of prefix and regroupg
comments again so that the g4x warning is right next to those defines.
Also add a _G4X suffix for those special ones. Also cc stable.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are two loops that are almost identical but only with different
checks. Refactor them with a simple helper, and give a bit more
comments what's doing there.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- transactional execution
- lpp sampling support
In addition there is also a fix to the virtio-ccw guest driver. This will
enable future features
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=GbUg
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-20140117' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-queue
This deals with 2 guest features that need enablement in the kvm host:
- transactional execution
- lpp sampling support
In addition there is also a fix to the virtio-ccw guest driver. This will
enable future features
The test here is intended intended to prevent shift wrapping bugs when
we do "1U << idx2". We should consider the number of bits in a u32
instead of the number of bytes.
[fix another chunk similarly by tiwai]
Fixes: 7bb2491b35 ('ALSA: Add kconfig to specify the max card numbers')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At IO preparation we calculate the max pages at each device and
allocate a BIO per device of that size. The calculation was wrong
on some unaligned corner cases offset/length combination and would
make prepare return with -ENOMEM. This would be bad for pnfs-objects
that would in that case IO through MDS. And fatal for exofs were it
would fail writes with EIO.
Fix it by doing the proper math, that will work in all cases. (I
ran a test with all possible offset/length combinations this time
round).
Also when reading we do not need to allocate for the parity units
since we jump over them.
Also lower the max_io_length to take into account the parity pages
so not to allocate BIOs bigger than PAGE_SIZE
CC: Stable Kernel <stable@vger.kernel.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Verify that reserved fields in struct mlx5_ib_resize_cq are cleared
before continuing execution of the verb. This is required to allow
making use of this area in future revisions.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
