Return the value obtained from get_coeff() instead of EINVAL.
Silences a smatch warning.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove remuxing GPIO1. Leave control of this up to the platform device.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
There is no mixer attached to the ASRC on the wm5110 only a multiplexer
to select the source for the single input line. This change correctly
defines this in the wm5110 CODEC driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no mixer attached to the ASRC on the wm5102 only a multiplexer
to select the source for the single input line. This change correctly
defines this in the wm5102 CODEC driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Asynchronous Sample Rate Converters on the wm5102/wm5110 have no
mixer attached to their input, but they do allow the input to be
selected from a number of sources via a multiplexer. Currently the
platform assumes the presence of 4 multiplexers and a mixer for each
block.
This patch adds support multiplexed single input blocks into the Arizona
platform.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In case of probe deferral, the allocated GPIO line is not freed, which
prevents it from being claimed and properly asserted in later attempts.
Fix this by using devm_gpio_request().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Michael Hirsch <hirsch@teufel.de>
Cc: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the firmware load and record parsing functionality out into
a separate function from the boot function.
Signed-off-by: Scott Ling <sl@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the return value of cs42l52_set_fmt() when clock inversion is
not allowed and also remove the useless variable ret.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
[We had been assigning to ret but then ignoring the value we assgined
-- broonie]
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
When MCLK is supplied externally and BCLK and LRC are configured as outputs
(codec is master), the PLL values are only calculated correctly on the first
transmission. On subsequent transmissions, at differenct sample rates, the
wrong PLL values are used. Test for f_opclk instead of f_pllout to determine
if the PLL values are needed.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Remove the boot_done counter variable and check the wm0010 state
variable instead.
Signed-off-by: Scott Ling <scott.ling@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the possibility to specify a gpio through platform data
so that a HW reset can be issued to the codec.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In its previous status, the first capture didn't work properly;
nothing was actually recorded from the microphone. This
behaviour was observed using a Visstrim M10 board.
In order to solve this BUG a workaround has been added that,
during the initialization process of the codec, powers on and
off the ADC.
The issue seems related to a HW BUG or some behavior that
is not documented in the datasheet.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Evalation of the WM5102 has identified a number of register values which
should be written after SYSCLK is enabled on revision A in order to
improve performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many Arizona class devices contain ADSP2 cores with a standard method for
hooking them into the audio map. Define standard helpers for this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many current Wolfson devices feature DSPs based around an architecture
known as ADSP. Since there is a lot of commonality in the system
integration of these devices a common library will be used to provide
support for them.
This version provides equivalent support for ADSP1 to that currently
included in the WM2200 driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use regmap-mmio instead of open-coding caching and register accessors.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use devm_request_and_ioremap for requesting and mapping the IO region. This
makes the code a bit smaller and simpler.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add dB TLV ranges for the various volume controls.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ARIZONA_MICB1_ENA_SHIFT was used for micbias 2 and 3. This change
correctly uses the ARIZONA_MICBX_ENA_SHIFT for each corresponding DAPM
supply. This should not have caused any problems as the micbias enables
are in the same place in each register.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than always assuming the maximum possible BCLK rate will be
required generate BCLKs for stereo if either one or two channels is
enabled. In order to support this we also need to ensure that only
the relevant channels are enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When lowering SYSCLK to 50kHz for accessory detection also lower the
AIFnCLK divisor to normalise the clocking configuration within the
device. This will not disrupt audio as we cannot support active audio
with such a low SYSCLK.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix wm2200.c printk format warnings (seen on x86_64):
sound/soc/codecs/wm2200.c:1027:4: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
sound/soc/codecs/wm2200.c:1139:5: warning: format '%d' expects type 'int', but argument 5 has type 'long unsigned int'
sound/soc/codecs/wm2200.c:1181:2: warning: format '%d' expects type 'int', but argument 7 has type 'size_t'
sound/soc/codecs/wm2200.c:1201:5: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
sound/soc/codecs/wm2200.c:1264:4: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
sound/soc/codecs/wm2200.c:1328:5: warning: format '%d' expects type 'int', but argument 5 has type 'long unsigned int'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch DAPMises headphone and lineout output enable controls.
Earlier these output enable bits were permanently turned on in probe.
In da9055 codec, right outmixer is directly connected with right HP and
Line out. This resulted in two side effects,
(1) When you only want to use lineout, right HP (and connected charge
pump) also gets enabled
(2) When you only want to use stereo HP, lineout also gets enabled
This patch adds three switches to select which output(s) should be
enabled.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Nothing too exciting except for the ams-delta change which is relatively
lerge due to the fact that the driver loading had been totally broken as
the driver needed a newer API to function.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lEIC
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.7
Nothing too exciting except for the ams-delta change which is relatively
lerge due to the fact that the driver loading had been totally broken as
the driver needed a newer API to function.
A bunch of updates to the regmap range support, the most important ones
being to rename "n_ranges" to "num_ranges" for consistency and to allow
block writes to cross page boundaries, making things more transparent.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Cdf2
-----END PGP SIGNATURE-----
Merge tag 'regmap/range' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into asoc-wm2200
regmap: Range API changes
A bunch of updates to the regmap range support, the most important ones
being to rename "n_ranges" to "num_ranges" for consistency and to allow
block writes to cross page boundaries, making things more transparent.
As of commit 99c2aa (firmware loader: fix creation failure of fw loader
device) we can have more than one firmware request outstanding at once so
there is no need to daisychain our requests any more.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This can be used to provide some additional settling time to ensure that
we don't start microphone detection while the microphone pin is connected
to one of the headphone pins.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is more idiomatic and ensures we don't try to do the ASoC card setup
until we've got all the required resources.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the device is now idle_bias_off these never have any useful effect,
the device will be brought to _OFF when idle, and will at best leave it
powered for longer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit add a sound codec driver for Silicon Laboratories 476x
series of AM/FM radio chips.
Signed-off-by: Andrey Smirnov <andrey.smirnov@convergeddevices.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds AIF DSP mode support for da9055 codec driver.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The CS4271 has a feature to sync its analog mute flags, so one mute
circuitry can be used for both channels.
Give users access to this feature with a new DT property and a flag in
the platform data.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
