The field is no longer initialised so this will crash if running on
wm8958.
Reported-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The thermal shutdown support in wm_hubs devices is tied to the speaker
drivers (which are the only high power subsystems within the device).
Ensure minimal current usage when the thermal shutdown support is not
required by disabling the circuit when the speaker drivers are powered
down.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Disable the thermal shutdown circuits for headphone and speaker when the
relevant outputs are not enabled in order to save current in idle modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM9081 thermal shutdown is only effective when the speaker output is
enabled so disable it when that is not in use for a small current saving.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Having a separate list for amps is a little confusing now the official
driver model for them is the same as for other CODECs so let's sort them
into the CODEC list, but only do this for those that are actual CODEC
drivers so it's easier to remember which ones need updating.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They aren't needed any more. If machines need them for other purposes then
further changes will be required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Force MICBIAS on as well as SYSCLK as the WM8962 accessory detection can't
function without both. No point in making machine drivers manually enable
it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we have code to automatically manage the start and stop of the FLL
based on the SYSCLK widget if SYSCLK is already enabled and the FLL is
configured then we need to start it up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since there is no current software control for these they would otherwise
be left enabled, consuming power.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The WM8962 has a separate software reset for the PLL registers. Ensure that
these are reset also on startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set `invert' bit for Capture Switch. Otherwise analogue is muted when
Capture Switch is ON.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Current implementation in wm8711_set_dai_fmt always clear BIT[3:2]
(the Input Audio Data Bit Length Select) of WM8711_IFACE(07h) register.
Input Audio Data Bit Length Select bits are set by wm8711_hw_params,
we should leave BIT[3:2] untouched in wm8711_set_dai_fmt.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The Input Audio Data Bit Length Select is controlled by BIT[3:2] of
WM8711_IFACE(07h) register.
Current code incorrectly masks BIT[1:0] which is for Audio Data Format Select.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
According to the datasheet:
Page0 / Register8: Audio Serial Data interface Control Register A
BIT 7: Bit Clock Directional Control
0: Bit clock is an input (slave mode)
1: Bit clock is an output (master mode)
BIT 6: Word Clock Directional Control
0: Word clock is an input (slave mode)
1: Word clock is an output (master mode)
Current code sets BIT_CLK_MASTER and WORD_CLK_MASTER bits for master mode,
but does not clear these bits for slave mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
Digital Audio Interface Format (07h) register:
BIT6: Master/slave mode
0: Slave
1: Master
Current code sets TLV320AIC23_MS_MASTER bit for master mode,
but does not clear it for slave mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
BCLK is controlled by BIT[4:2] of WM8940_CLOCK(06h) register.
Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Chris Paulson-Ellis <chris@edesix.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The registers are 16 bits, thus remove an extra F for the mask.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet:
The PLL Output clock division ratio is controlled by BIT[5:4] of
WM8940_GPIO register(08h).
Current code read/write the WM8940_ADDCNTRL(07h) register which is wrong.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
What we want here is to clear the WM8400_FLL_OUTDIV_MASK bits then
OR with factors.outdiv.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
codec->hw_write is broken now, convert codec->hw_write to snd_soc_write.
The hardware has 2 banks of registers sharing a section in I2C register space.
The 1st bank is the primary one and is cached.
The 2nd bank is for loading coefficients only and they do not need cache.
These coefficients registers are therefore direct writes.
Thus we set cache_bypass flag to deal with this before calling snd_soc_write.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure all mask bits are clear before setting new value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
DA7210 has three line outputs. OUT1 Left, OUT1 Right and OUT2 (mono).
This patch adds support for gain controls for these three line outs.
It also adds support for overall DAC gain control.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for DAPM covering all inputs and outputs
as well as ADC and DAC.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have defined SGTL5000_LINREG_VDDD_MASK in sgtl5000.h,
use it instead of hardcoded (0x1 << 4) - 1 for the mask.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise calling ldo_regulator_remove() does not unregister regulator
and free memories.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
