Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8962 has ground referenced and class D outputs so can happily go
down to BIAS_OFF without a large startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 33c5f969 "ASoC: Allow idle_bias_off to be specified in CODEC
drivers", now we can set idle_bias_off flag in struct snd_soc_codec_driver
for devices can unconditionally support idle_bias_off.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For optimal performance the single ended line outputs require that the
line output VMID buffer be enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Report any accessory with a low impedance as a headphone, previously
anything other than a short or microphone would not be reported at all.
The most likely reason is a microphone with incorrect polarity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using pm_runtime to decide if the device should go into full power down
has the dual advantage of allowing easier integration with non-DAPM
reasons to power on the device (like the FLL) and allowing userspace to
control the final power down which is useful for tuning retention of
DSP firmware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to avoid breakage change the omap-abe-twl6040
machine driver's routing.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to write the configuration for each microphone to a different
register.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
When we have identified an accessory make sure we've flagged that we've
done so in order to make sure we always report buttons and don't continue
to polarity flip.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the hardware is configured with one or both of the IN4 inputs used
for DC measurement (with no DC blocking capacitor connected) then we can
improve power consumption slightly in idle modes by applying a register
write sequence. Provide platform data to enable this, implemented using
a regmap patch.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In wm2000_i2c_probe(), if we take the true branch in
"
ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_wm2000,
NULL, 0);
if (ret != 0)
goto err_fw;
"
then we'll release_firmware(fw) at the 'err_fw' label. But we've already
done that just a few lines above. That's a use-after-free bug.
This patch restructures the code so that we always call
release_firmware(fw) before leaving the function, but only ever call
it once.
This means that we have to initialize 'fw' to NULL since some paths
may now end up calling it without having called request_firmware(),
but since request_firmware() deals gracefully with NULL pointers, we
are fine if we just NULL initialize it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To print a value of type size_t one should use %zd, not %d.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix below build warning when CONFIG_HOTPLUG is not set.
CC sound/soc/codecs/alc5623.o
sound/soc/codecs/alc5623.c:1062: warning: ‘alc5623_i2c_remove’ defined but not used
CC sound/soc/codecs/alc5632.o
sound/soc/codecs/alc5632.c:1112: warning: ‘alc5632_i2c_remove’ defined but not used
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to table based DAPM and control init.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should be allowing a 5ms delay after the charge pump is started in
order to ensure it has finished ramping.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The problem was introduced due to the obscure formatting some of the
older drivers use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is more what the device model wants us to do and will allow use by
non-audio functions before the audio part of the device has come up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will allow us to move the interrupt allocation out of the ASoC part
of the driver and simplifies the locking by removing any reliance in the
bulk of the interrupt path on the big CODEC lock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Core can set the msbits constraint in behalf of the dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Core can set the msbits constraint in behalf of the dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Throughout the sgtl5000 driver source code and also in the sgtl5000 datasheet
the revision code is shown in hexadecimal.
Print it hex format, for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If an interrupt is supplied then use it for thermal warning and FLL lock
notifications. When using the interrupt raise the timeout for the FLL lock
substantially to reduce the chances of spurious warnings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
