We started using the connector table on nv4x a while back, and this VBIOS
has bad connector indices which causes the wrong encoders to get paired
with connectors.
Add a quirk to fix this...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Clearing bit 5 of CACHE_MODE_0 is necessary to prevent GPU hangs in
OpenGL programs such as Google MapsGL, Google Earth, and gzdoom when
using separate stencil buffers. Without it, the GPU tries to use the
LRA eviction policy, which isn't supported. This was supposed to be off
by default, but seems to be on for many machines.
This cannot be done in gen6_init_clock_gating with most of the other
workaround bits; the render ring needs to exist. Otherwise, the
register write gets dropped on the floor (one printk will show it
changed, but a second printk immediately following shows the value
reverts to the old one).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47535
Cc: stable@vger.kernel.org
Cc: Rob Castle <futuredub@gmail.com>
Cc: Eric Appleman <erappleman@gmail.com>
Cc: aaron667@gmx.net
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some boards such as the Intel D2700MUD allow you to have over 4GB of RAM.
The GTT on the PVR based devices is 32bit however. Hugh Dickins points out
that we should therefore be setting the mapping gfp mask.
This is not the whole fix for the problem. Some further shmem patches will
be needed to deal with the corner cases.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This provides the needed callback hooks to add hotplug display support to
the GMA36x0 devices.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In particular clean up the errata handling and correct the crtc masks. We do
this a bit differently using our device abstraction for neatness.
This doesn't address the ACPI opregion and hotplug plumbing, nor the IRQ related
changes that will need. It touches on backlight init but the full backlight
support is not in this change set.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The problem in console mode is lack of linear memory. We can solve that by
dropping to 16bpp. The mode setting X server will allocate its own GEM
framebuffer in 32bpp and all will be well.
We could just do 16bpp anyway but that would be a regression on the lower
modes as many distributions don't yet ship the generic mode setting KMS
drivers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Introduce a panel presence check for Cedartrail. Non netbook devices don't
necessarily have a panel attached.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull in various i915 bits that we will need to begin tackling the LVDS detect
and ACPI events. We try and drift towards the i915 version of the code with
the long term goal that at least some of it can one day be unified.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We don't want them uncached, combining will do nicely and fixes the performance
problem with the generic modesetting X server.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to pull more stuff from the VBT in order to configure the clocking
correctly in all cases. Add the relevant bits from the other CDV driver work.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This was reported a long time ago (and I apologize to whoever it was that
reported it as I've lost the original report).
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
An entry for INTERNAL_VCE encoder was missing. Add it.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
EDID vendor IDs are always 3 characters long (4 with the terminating
0). It doesn't make any sense to have a (possibly 8-byte) pointer
to the ID string in the quirk structure.
Signed-off-by: Ian Pilcher <arequipeno@gmail.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Requiring the first byte of the EDID base block header to be 0 means we
don't fix up as many transfer errors as we could. Instead have the
callers specify whether it's meant to be block 0 or not, and
conditionally run header fixup based on that.
Bugzilla: https://bugzilla.redhat.com/812890
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From Daniel Vetter
- VGA load-detect fix. This bug seems to be as old as the load-detect code
(2.6.30), but needs stupid userspace (upowerd trying to detect
connectors on dpms-off outputs) to actually kill the machine. And
obviously a machine without VGA-hotplug, otherwise we don't do load
detect.
- 2 interger overflow fixes for unpriviledged ioctls from Xi Wang.
- Fix SDVO regression for low-res (pixelclock < 100MHz) digital outputs,
introduce in 2.6.36.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: handle input/output sdvo timings separately in mode_set
drm/i915: fix integer overflow in i915_gem_do_execbuffer()
drm/i915: fix integer overflow in i915_gem_execbuffer2()
drm/i915: fixup load-detect on enabled, but not active pipe
From Inki Dae:
this patch set fixes gem allocation and mapping issue between user space and
physical memory region.
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-2.6-samsung:
drm/exynos: added missed vm area region mapping type.
drm/exynos: fixed exynos_drm_gem_map_pages bug.
drm/exynos: fixed duplicatd memory allocation bug.
We seem to have a decent confusion between the output timings and the
input timings of the sdvo encoder. If I understand the code correctly,
we use the original mode unchanged for the output timings, safe for
the lvds case. And we should use the adjusted mode for input timings.
Clarify the situation by adding an explicit output_dtd to the sdvo
mode_set function and streamline the code-flow by moving the input and
output mode setting in the sdvo encode together.
Furthermore testing showed that the sdvo input timing needs the
unadjusted dotclock, the sdvo chip will automatically compute the
required pixel multiplier to get a dotclock above 100 MHz.
Fix this up when converting a drm mode to an sdvo dtd.
This regression was introduced in
commit c74696b9c8
Author: Pavel Roskin <proski@gnu.org>
Date: Thu Sep 2 14:46:34 2010 -0400
i915: revert some checks added by commit 32aad86f
particularly the following hunk:
diff --git a/drivers/gpu/drm/i915/intel_sdvo.c
b/drivers/gpu/drm/i915/intel_sdvo.c
index 093e914..62d22ae 100644
--- a/drivers/gpu/drm/i915/intel_sdvo.c
+++ b/drivers/gpu/drm/i915/intel_sdvo.c
@@ -1122,11 +1123,9 @@ static void intel_sdvo_mode_set(struct drm_encoder *encoder,
/* We have tried to get input timing in mode_fixup, and filled into
adjusted_mode */
- if (intel_sdvo->is_tv || intel_sdvo->is_lvds) {
- intel_sdvo_get_dtd_from_mode(&input_dtd, adjusted_mode);
+ intel_sdvo_get_dtd_from_mode(&input_dtd, adjusted_mode);
+ if (intel_sdvo->is_tv || intel_sdvo->is_lvds)
input_dtd.part2.sdvo_flags = intel_sdvo->sdvo_flags;
- } else
- intel_sdvo_get_dtd_from_mode(&input_dtd, mode);
/* If it's a TV, we already set the output timing in mode_fixup.
* Otherwise, the output timing is equal to the input timing.
Due to questions raised in review, below a more elaborate analysis of
the bug at hand:
Sdvo seems to have two timings, one is the output timing which will be
sent over whatever is connected on the other side of the sdvo chip (panel,
hdmi screen, tv), the other is the input timing which will be generated by
the gmch pipe. It looks like sdvo is expected to scale between the two.
To make things slightly more complicated, we have a bunch of special
cases:
- For lvds panel we always use a fixed output timing, namely
intel_sdvo->sdvo_lvds_fixed_mode, hence that special case.
- Sdvo has an interface to generate a preferred input timing for a given
output timing. This is the confusing thing that I've tried to clear up
with the follow-on patches.
- A special requirement is that the input pixel clock needs to be between
100MHz and 200MHz (likely to keep it within the electromechanical design
range of PCIe), 270MHz on later gen4+. Lower pixel clocks are
doubled/quadrupled.
The thing this patch tries to fix is that the pipe needs to be
explicitly instructed to double/quadruple the pixels and needs the
correspondingly higher pixel clock, whereas the sdvo adaptor seems to
do that itself and needs the unadjusted pixel clock. For the sdvo
encode side we already set the pixel mutliplier with a different
command (0x21).
This patch tries to fix this mess by:
- Keeping the output mode timing in the unadjusted plain mode, safe
for the lvds case.
- Storing the input timing in the adjusted_mode with the adjusted
pixel clock. This way we don't need to frob around with the core
crtc mode set code.
- Fixing up the pixelclock when constructing the sdvo dtd timing
struct. This is why the first hunk of the patch is an integral part
of the series.
- Dropping the is_tv special case because input_dtd is equivalent to
adjusted_mode after these changes. Follow-up patches clear this up
further (by simply ripping out intel_sdvo->input_dtd because it's
not needed).
v2: Extend commit message with an in-depth bug analysis.
Reported-and-Tested-by: Bernard Blackham <b-linuxgit@largestprime.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48157
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The error handling code w.r.t. idr usage looks inconsistent.
In the case of drm_mode_object_get() and drm_ctxbitmap_next() the error
handling is also incomplete.
Unify the code to follow the same pattern always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vga-switcheroo currently changes the default VGA device by fiddling with
the IORESOURCE_ROM_SHADOW flag on the device. This isn't strictly accurate,
since there's no guarantee that switching also changes the ROM decoding.
Switch over to using the vgaarb functions for this.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The default VGA device is a somewhat fluid concept on platforms with
multiple GPUs. Add support for setting it so switching code can update
things appropriately, and make sure that the sysfs code returns the right
device if it's changed.
v2: Updated to fix builds when __ARCH_HAS_VGA_DEFAULT_DEVICE is false.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: benh@kernel.crashing.org
Cc: airlied@redhat.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
- add support for rs6xx
- add support for DCE4/5
- fixup 6xx/7xx
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds register definitions for HDMI/DP audio on
DCE2/3/4/5 hardware.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Improve handling of bpc (bits per color) in radeon.
In most cases we want 8 except for HDMI, DP, LVDS, and eDP.
v2: handle DP better.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On 32-bit systems, a large args->num_cliprects from userspace via ioctl
may overflow the allocation size, leading to out-of-bounds access.
This vulnerability was introduced in commit 432e58ed ("drm/i915: Avoid
allocation for execbuffer object list").
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On 32-bit systems, a large args->buffer_count from userspace via ioctl
may overflow the allocation size, leading to out-of-bounds access.
This vulnerability was introduced in commit 8408c282 ("drm/i915:
First try a normal large kmalloc for the temporary exec buffers").
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HD panel (1366x768) found most commonly on laptops can't be represented
exactly in CVT/DMT expression, which leads to 1368x768 instead, because
1366 can't be divided by 8.
Add a hack to convert to 1366x768 manually as an exception.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
with this patch, if the memory region is physically non-continuous
then VM_MIXEDMAP is set to vm->vm_flags otherwise VM_PFNMAP.
we had missed this flag setting.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
this patch fixes the problem that the physical memory region to be mapped
to user space could be exceeded. if page fault address was placed at between
buffer start and end then memory region to be mapped would be exceeded.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
the gem was already allocated at gem allocation time but is allocated
at page fault handler so this patch fixes the problem that gem was
allocated one more time.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Chris' fix for my 32b breakage was incorrect. do_div returns a
remainder. Go back to a divide macro which is more 32b friendly.
Tested on x86-64.
This has only been compile tested on 32b systems.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48756
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Sincere-apologies: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
[danvet: fixup 32bit compile-fail.]
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow we have a fast-path that tries to avoid going through
the load-detect code when the encode already has a crtc associated.
But this fails horribly when the crtc is off. The load detect pipe
itself manages this case well (and also does not forget to restore the
dpms state), so just rip out this special case.
The issue seems to go back all the way to the commit that originally
introduced load-detection on the vga output:
commit e4a5d54f92
Author: Ma Ling <ling.ma@intel.com>
Date: Tue May 26 11:31:00 2009 +0800
drm/i915: Add support for VGA load detection (pre-945).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43020
Reported-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This continues the theme started with vm_brk() and vm_munmap():
vm_mmap() does the same thing as do_mmap(), but additionally does the
required VM locking.
This uninlines (and rewrites it to be clearer) do_mmap(), which sadly
duplicates it in mm/mmap.c and mm/nommu.c. But that way we don't have
to export our internal do_mmap_pgoff() function.
Some day we hopefully don't have to export do_mmap() either, if all
modular users can become the simpler vm_mmap() instead. We're actually
very close to that already, with the notable exception of the (broken)
use in i810, and a couple of stragglers in binfmt_elf.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Like the vm_brk() function, this is the same as "do_munmap()", except it
does the VM locking for the caller.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some common sizes that don't show up in DMT.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We want the same type for extra modes inferred from ranges.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
EDID 1.4 retcons the meaning of the "GTF feature" bit to mean "is
continuous frequency", and moves the set of supported timing formulas
into the range descriptor itself. In any event, the range descriptor
can act as a filter on the DMT list without regard to a specific timing
formula.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
