* pci/host-aardvark:
arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700
PCI: aardvark: Add Aardvark PCI host controller driver
dt-bindings: add DT binding for the Aardvark PCIe controller
* pci/host-altera:
PCI: altera: Poll for link up status after retraining the link
PCI: altera: Check link status before retrain link
PCI: altera: Reorder read/write functions
* pci/host-dra7xx:
PCI: dra7xx: Fix return value in case of error
* pci/host-hv:
PCI: hv: Fix interrupt cleanup path
PCI: hv: Handle all pending messages in hv_pci_onchannelcallback()
PCI: hv: Don't leak buffer in hv_pci_onchannelcallback()
* pci/host-vmd:
x86/PCI: VMD: Separate MSI and MSI-X vector sharing
x86/PCI: VMD: Use x86_vector_domain as parent domain
x86/PCI: VMD: Use lock save/restore in interrupt enable path
x86/PCI: VMD: Initialize list item in IRQ disable
x86/PCI: VMD: Select device dma ops to override
* pci/host-xilinx:
PCI: xilinx: Fix return value in case of error
Manually apply changes from pci/demodularize-hosts and
pci/host-request-windows to drivers/pci/host/pci-aardvark.c
* pci/host-tegra:
PCI: tegra: Program PADS_REFCLK_CFG* registers with per-SoC values
PCI: tegra: Program PADS_REFCLK_CFG* always, not just on legacy SoCs
PCI: tegra: Stop setting pcibios_min_mem
PCI: tegra: Use generic pci_remap_iospace() rather than ARM32-specific one
PCI: tegra: Use lower-case hex consistently for register definitions
Conflicts:
drivers/pci/host/pci-tegra.c
Drop stray pci_ioremap_io() per Thierry Reding <treding@nvidia.com>;
removal tested by Jon Hunter <jonathanh@nvidia.com>.
* pci/resource:
unicore32/PCI: Remove pci=firmware command line parameter handling
ARM/PCI: Remove arch-specific pcibios_enable_device()
ARM64/PCI: Remove arch-specific pcibios_enable_device()
MIPS/PCI: Claim bus resources on PCI_PROBE_ONLY set-ups
ARM/PCI: Claim bus resources on PCI_PROBE_ONLY set-ups
PCI: generic: Claim bus resources on PCI_PROBE_ONLY set-ups
PCI: Add generic pci_bus_claim_resources()
alx: Use pci_(request|release)_mem_regions
ethernet/intel: Use pci_(request|release)_mem_regions
GenWQE: Use pci_(request|release)_mem_regions
lpfc: Use pci_(request|release)_mem_regions
NVMe: Use pci_(request|release)_mem_regions
PCI: Add helpers to request/release memory and I/O regions
PCI: Extending pci=resource_alignment to specify device/vendor IDs
sparc/PCI: Implement pci_resource_to_user() with pcibios_resource_to_bus()
powerpc/pci: Implement pci_resource_to_user() with pcibios_resource_to_bus()
microblaze/PCI: Implement pci_resource_to_user() with pcibios_resource_to_bus()
PCI: Unify pci_resource_to_user() declarations
microblaze/PCI: Remove useless __pci_mmap_set_pgprot()
powerpc/pci: Remove __pci_mmap_set_pgprot()
PCI: Ignore write combining when mapping I/O port space
* pci/aspm:
PCI/ASPM: Remove redundant check of pcie_set_clkpm
* pci/dpc:
PCI: Remove DPC tristate module option
PCI: Bind DPC to Root Ports as well as Downstream Ports
PCI: Fix whitespace in struct dpc_dev
PCI: Convert Downstream Port Containment driver to use devm_* functions
* pci/hotplug:
PCI: Allow additional bus numbers for hotplug bridges
* pci/misc:
PCI: Include <asm/dma.h> for isa_dma_bridge_buggy
PCI: Make bus_attr_resource_alignment static
MAINTAINERS: Add file patterns for PCI device tree bindings
PCI: Fix comment typo
* pci/msi:
PCI/MSI: irqchip: Fix PCI_MSI dependencies
* pci/pm:
PCI: pciehp: Ignore interrupts during D3cold
PCI: Document connection between pci_power_t and hardware PM capability
PCI: Add runtime PM support for PCIe ports
ACPI / hotplug / PCI: Runtime resume bridge before rescan
PCI: Power on bridges before scanning new devices
PCI: Put PCIe ports into D3 during suspend
PCI: Don't clear d3cold_allowed for PCIe ports
PCI / PM: Enforce type casting for pci_power_t
* pci/virtualization:
PCI: Add ACS quirk for Solarflare SFC9220
PCI: Add DMA alias quirk for Adaptec 3805
PCI: Mark Atheros AR9485 and QCA9882 to avoid bus reset
PCI: Add function 1 DMA alias quirk for Marvell 88SE9182
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_XGENE
drivers/pci/host/Kconfig: bool "X-Gene PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tanmay Inamdar <tinamdar@apm.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_HOST_THUNDER_PEM
drivers/pci/host/Kconfig: bool "Cavium Thunder PCIe controller to off-chip devices"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: David Daney <david.daney@cavium.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_HOST_THUNDER_ECAM
drivers/pci/host/Kconfig: bool "Cavium Thunder ECAM controller to on-chip devices on pass-1.x silicon"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: David Daney <david.daney@cavium.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_TEGRA
drivers/pci/host/Kconfig: bool "NVIDIA Tegra PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-tegra@vger.kernel.org
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_RCAR_GEN2
drivers/pci/host/Kconfig: bool "Renesas R-Car Gen2 Internal PCI controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
CC: Valentine Barshak <valentine.barshak@cogentembedded.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_RCAR_GEN2_PCIE
drivers/pci/host/Kconfig: bool "Renesas R-Car PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_MVEBU
drivers/pci/host/Kconfig: bool "Marvell EBU PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Jason Cooper <jason@lakedaemon.net>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_LAYERSCAPE
drivers/pci/host/Kconfig: bool "Freescale Layerscape PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Minghuan Lian <minghuan.Lian@freescale.com>
CC: Mingkai Hu <mingkai.hu@freescale.com>
CC: Roy Zang <tie-fei.zang@freescale.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_KEYSTONE
drivers/pci/host/Kconfig: bool "TI Keystone PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-By: Murali Karicheri <m-karicheri2@ti.com>
This code is not being built as a module by anyone:
host/Kconfig:config PCI_HISI
host/Kconfig: bool "HiSilicon Hip05 and Hip06 SoCs PCIe controllers"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Zhou Wang <wangzhou1@hisilicon.com>
CC: Dacai Zhu <zhudacai@hisilicon.com>
CC: Gabriele Paoloni <gabriele.paoloni@huawei.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_HOST_GENERIC
drivers/pci/host/Kconfig: bool "Generic PCI host controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCIE_DW_PLAT
drivers/pci/host/Kconfig: bool "Platform bus based DesignWare PCIe Controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCIE_ARTPEC6
drivers/pci/host/Kconfig: bool "Axis ARTPEC-6 PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog, add "Author" comment]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Niklas Cassel <niklas.cassel@axis.com>
CC: Jesper Nilsson <jesper.nilsson@axis.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCIE_ARMADA_8K
drivers/pci/host/Kconfig: bool "Marvell Armada-8K PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We are now able to support KVM T&E with MIPS32 guests on some MIPS64r2
and MIPS64r6 hosts, so select HAVE_KVM so it can be enabled.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM sometimes flushes host TLB entries, reading each one to check if it
corresponds to a guest KSeg0 address. In the absence of EntryHi.EHInv
bits to invalidate the whole entry, the entries will be set to unique
virtual addresses in KSeg0 (which is not TLB mapped), spaced 2*PAGE_SIZE
apart.
The TLB read however will clobber the CP0_PageMask register with
whatever page size that TLB entry had, and that same page size will be
written back into the TLB entry along with the unique address.
This would cause breakage when transparent huge pages are enabled on
64-bit host kernels, since huge page entries will overlap other nearby
entries when separated by only 2*PAGE_SIZE, causing a machine check
exception.
Fix this by restoring the old CP0_PageMask value (which should be set to
the normal page size) after reading the TLB entry if we're going to go
ahead and invalidate it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_mips_trans_replace() passes a pointer to KVM_GUEST_KSEGX(). This
breaks on 64-bit builds due to the cast of that 64-bit pointer to a
different sized 32-bit int. Cast the pointer argument to an unsigned
long to work around the warning.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When emulating MFC0 instructions to load 32-bit values from guest COP0
registers and the RDHWR instruction to read the CC (Count) register,
sign extend the result to comply with the MIPS64 architecture. The
result must be in canonical 32-bit form or the guest may malfunction.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MFC0 and MTC0 instructions in the guest which cause traps can be
replaced with 32-bit loads and stores to the commpage, however on big
endian 64-bit builds the offset needs to have 4 added so as to
load/store the least significant half of the long instead of the most
significant half.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fail if the address of the allocated exception base doesn't fit into the
CP0_EBase register. This can happen on MIPS64 if CP0_EBase.WG isn't
implemented but RAM is available outside of the range of KSeg0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the KVM entry point to write CP0_EBase as a 64-bit register when
it is 64-bits wide, and to set the WG (write gate) bit if it exists in
order to write bits 63:30 (or 31:30 on MIPS32).
Prior to MIPS64r6 it was UNDEFINED to perform a 64-bit read or write of
a 32-bit COP0 register. Since this is dynamically generated code,
generate the right type of access depending on whether the kernel is
64-bit and cpu_has_ebase_wg.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the KVM entry code to set the CP0_Entry.KX bit on 64-bit kernels.
This is important to allow the entry code, running in kernel mode, to
access the full 64-bit address space right up to the point of entering
the guest, and immediately after exiting the guest, so it can safely
restore & save the guest context from 64-bit segments.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MIPS KVM entry code (originally kvm_locore.S, later locore.S, and
now entry.c) has never quite been right when built for 64-bit, using
32-bit instructions when 64-bit instructions were needed for handling
64-bit registers and pointers. Fix several cases of this now.
The changes roughly fall into the following categories.
- COP0 scratch registers contain guest register values and the VCPU
pointer, and are themselves full width. Similarly CP0_EPC and
CP0_BadVAddr registers are full width (even though technically we
don't support 64-bit guest address spaces with trap & emulate KVM).
Use MFC0/MTC0 for accessing them.
- Handling of stack pointers and the VCPU pointer must match the pointer
size of the kernel ABI (always o32 or n64), so use ADDIU.
- The CPU number in thread_info, and the guest_{user,kernel}_asid arrays
in kvm_vcpu_arch are all 32 bit integers, so use lw (instead of LW) to
load them.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are several unportable uses of CKSEG0ADDR() in MIPS KVM, which
implicitly assume that a host physical address will be in the low 512MB
of the physical address space (accessible in KSeg0). These assumptions
don't hold for highmem or on 64-bit kernels.
When interpreting the guest physical address when reading or overwriting
a trapping instruction, use kmap_atomic() to get a usable virtual
address to access guest memory, which is portable to 64-bit and highmem
kernels.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Calculate the PFN of the commpage using virt_to_phys() instead of
CPHYSADDR(). This is more portable as kzalloc() may allocate from XKPhys
instead of KSeg0 on 64-bit kernels, which CPHYSADDR() doesn't handle.
This is sufficient for highmem kernels too since kzalloc() will allocate
from lowmem in KSeg0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KSEGX() macro is defined to 32-bit sign extend the address argument
and logically AND the result with 0xe0000000, with the final result
usually compared against one of the CKSEG macros. However the literal
0xe0000000 is unsigned as the high bit is set, and is therefore
zero-extended on 64-bit kernels, resulting in the sign extension bits of
the argument being masked to zero. This results in the odd situation
where:
KSEGX(CKSEG) != CKSEG
(0xffffffff80000000 & 0x00000000e0000000) != 0xffffffff80000000)
Fix this by 32-bit sign extending the 0xe0000000 literal using
_ACAST32_.
This will help some MIPS KVM code handling 32-bit guest addresses to
work on 64-bit host kernels, but will also affect KSEGX in
dec_kn01_be_backend() on a 64-bit DECstation kernel, and the SiByte DMA
page ops KSEGX check in clear_page() and copy_page() on 64-bit SB1
kernels, neither of which appear to be designed with 64-bit segments in
mind anyway.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We need to set cpsr before determining the spsr bank, as the bank
depends on the target exception level of the injection, not the
current mode of the vcpu. Normally this is one in the same (EL1),
but not when we manage to trap an EL0 fault. It still doesn't really
matter for the 64-bit EL0 case though, as vcpu_spsr() unconditionally
uses the EL1 bank for that. However the 32-bit EL0 case gets fun, as
that path will lead to the BUG() in vcpu_spsr32().
This patch fixes the assignment order and also modifies some white
space in order to better group pairs of lines that have strict order.
Cc: stable@vger.kernel.org # v4.5
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
commit 3c8f7710c1 ("ASoC: fix broken pxa SoC support") has removed
the SND_ARM dependency from SND_PXA2XX_LIB and SND_PXA2XX_LIB_AC97,
by moving these config entries outside of the "if SND_ARM ... endif"
construct.
However, by placing these 2 symbols right between the SND_ARM
menuconfig definition and the first SND_ARM menu entry, the side
effect is that the SND_ARM menu becomes empty and all the config
entries caught between "if SND_ARM ... endif" no more belong to
menuconfig SND_ARM, but to its parent (menuconfig SND).
Fix this.
Signed-off-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As reported by Zijun, the fdt_check_header() call in __fixmap_remap_fdt()
is not safe since it is not guaranteed that the FDT header is mapped
completely. Due to the minimum alignment of 8 bytes, the only fields we
can assume to be mapped are 'magic' and 'totalsize'.
Since the OF layer is in charge of validating the FDT image, and we are
only interested in making reasonably sure that the size field contains
a meaningful value, replace the fdt_check_header() call with an explicit
comparison of the magic field's value against the expected value.
Cc: <stable@vger.kernel.org>
Reported-by: Zijun Hu <zijun_hu@htc.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Kexec needs to know the addresses of all VMCSs that are active on
each CPU, so that it can flush them from the VMCS caches. It is
safe to record superfluous addresses that are not associated with
an active VMCS, but it is not safe to omit an address associated
with an active VMCS.
After a call to vmcs_load, the VMCS that was loaded is active on
the CPU. The VMCS should be added to the CPU's list of active
VMCSs before it is loaded.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
KVM maintains L1's current VMCS in guest memory, at the guest physical
page identified by the argument to VMPTRLD. This makes hairy
time-of-check to time-of-use bugs possible,as VCPUs can be writing
the the VMCS page in memory while KVM is emulating VMLAUNCH and
VMRESUME.
The spec documents that writing to the VMCS page while it is loaded is
"undefined". Therefore it is reasonable to load the entire VMCS into
an internal cache during VMPTRLD and ignore writes to the VMCS page
-- the guest should be using VMREAD and VMWRITE to access the current
VMCS.
To adhere to the spec, KVM should flush the current VMCS during VMPTRLD,
and the target VMCS during VMCLEAR (as given by the operand to VMCLEAR).
Since this implementation of VMCS caching only maintains the the current
VMCS, VMCLEAR will only do a flush if the operand to VMCLEAR is the
current VMCS pointer.
KVM will also flush during VMXOFF, which is not mandated by the spec,
but also not in conflict with the spec.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is known that PMU isn't working in some virtualized environments.
Modify the message issued in that case to mention why hardware PMU
isn't usable instead of reporting it to be broken.
As a side effect this will correct a little bug in the error message:
The error message was meant to be either of level err or info
depending on the environment (native or virtualized). As the level is
taken from the format string and not the printed string, specifying
it via %s and a conditional argument didn't work the way intended.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Link: http://lkml.kernel.org/r/1470051427-16795-1-git-send-email-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Add support for an enable regulator to lp855x_bl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=rUNA
-----END PGP SIGNATURE-----
Merge tag 'backlight-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Add support for an enable regulator to lp855x_bl"
* tag 'backlight-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: lp855x: Add enable regulator
- New API to call bespoke pre/post IRQ handlers; Regmap
- New Device Support
- Add support for RN5T567 to rn5t618
- Add support for COMe-cSL6 and COMe-mAL10 to kempld-core
- New Functionality
- Add support for USB Power Supply to axp20x
- Add support for Power Key to hi655x-pmic
- Fix-ups
- Update MAINTAINERS; Dialog, Altera
- Remove module support; max77843, max77620, max8998, max8997, max8925-i2c
- Add module support; max14577
- Constifying; max77620
- Allow bespoke IRQ masking/unmasking; max77620
- Remove superfluous code; arizona, qcom_rpm, smsc-ece1099
- Power Management fixups; arizona-core
- Error-path improvement; twl-core, dm355evm_msp, smsc-ece1099, hi655x
- Clocking fixups; twl6040
- Trivial (spelling, headers, coding-style, whitespace, (re)naming);
si476x-i2c, omap-usb-tll, ti_am335x_tscadc, tps6507, hi655x-pmic
- Bug Fixes
- Fix offset error for MSM8660; qcom_rpm
- Fix possible spurious IRQs; arizona, hi655x-pmic
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=KB2d
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- New API to call bespoke pre/post IRQ handlers; Regmap
New Device Support:
- Add support for RN5T567 to rn5t618
- Add support for COMe-cSL6 and COMe-mAL10 to kempld-core
New Functionality:
- Add support for USB Power Supply to axp20x
- Add support for Power Key to hi655x-pmic
Fix-ups:
- Update MAINTAINERS; Dialog, Altera
- Remove module support; max77843, max77620, max8998, max8997, max8925-i2c
- Add module support; max14577
- Constifying; max77620
- Allow bespoke IRQ masking/unmasking; max77620
- Remove superfluous code; arizona, qcom_rpm, smsc-ece1099
- Power Management fixups; arizona-core
- Error-path improvement; twl-core, dm355evm_msp, smsc-ece1099, hi655x
- Clocking fixups; twl6040
- Trivial (spelling, headers, coding-style, whitespace, (re)naming);
si476x-i2c, omap-usb-tll, ti_am335x_tscadc, tps6507, hi655x-pmic
Bug Fixes:
- Fix offset error for MSM8660; qcom_rpm
- Fix possible spurious IRQs; arizona, hi655x-pmic"
* tag 'mfd-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (42 commits)
mfd: qcom_rpm: Parametrize also ack selector size
mfd: twl6040: Handle mclk used for HPPLL and optional internal clock source
mfd: Add support for COMe-cSL6 and COMe-mAL10 to Kontron PLD driver
mfd: hi655x: Fix return value check in hi655x_pmic_probe()
mfd: smsc-ece1099: Return directly after a function failure in smsc_i2c_probe()
mfd: smsc-ece1099: Delete an unnecessary variable initialisation in smsc_i2c_probe()
mfd: dm355evm_msp: Return directly after a failed platform_device_alloc() in add_child()
mfd: twl-core: Refactoring for add_numbered_child()
mfd: twl-core: Return directly after a failed platform_device_alloc() in add_numbered_child()
mfd: arizona: Add missing disable of PM runtime on probe error path
mfd: stmpe: Move platform data into MFD driver
mfd: max14577: Allow driver to be built as a module
mfd: max14577: Use module_init() instead of subsys_initcall()
mfd: arizona: Remove some duplicate defines
mfd: qcom_rpm: Remove unused define
mfd: hi655x-pmic: Add powerkey device to hi655x PMIC driver
mfd: hi655x-pmic: Rename some interrupt macro names
mfd: hi655x-pmic: Fixup issue with un-acked interrupts
mfd: arizona: Check if AOD interrupts are pending before dispatching
mfd: qcom_rpm: Fix offset error for msm8660
...
In the updates:
* Big endian support and preparation for defered probing for the
Exynos IOMMU driver
* Simplifications in iommu-group id handling
* Support for Mediatek generation one IOMMU hardware
* Conversion of the AMD IOMMU driver to use the generic IOVA
allocator. This driver now also benefits from the recent
scalability improvements in the IOVA code.
* Preparations to use generic DMA mapping code in the Rockchip
IOMMU driver
* Device tree adaption and conversion to use generic page-table
code for the MSM IOMMU driver
* An iova_to_phys optimization in the ARM-SMMU driver to greatly
improve page-table teardown performance with VFIO
* Various other small fixes and conversions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xiS2
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- big-endian support and preparation for defered probing for the Exynos
IOMMU driver
- simplifications in iommu-group id handling
- support for Mediatek generation one IOMMU hardware
- conversion of the AMD IOMMU driver to use the generic IOVA allocator.
This driver now also benefits from the recent scalability
improvements in the IOVA code.
- preparations to use generic DMA mapping code in the Rockchip IOMMU
driver
- device tree adaption and conversion to use generic page-table code
for the MSM IOMMU driver
- an iova_to_phys optimization in the ARM-SMMU driver to greatly
improve page-table teardown performance with VFIO
- various other small fixes and conversions
* tag 'iommu-updates-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (59 commits)
iommu/amd: Initialize dma-ops domains with 3-level page-table
iommu/amd: Update Alias-DTE in update_device_table()
iommu/vt-d: Return error code in domain_context_mapping_one()
iommu/amd: Use container_of to get dma_ops_domain
iommu/amd: Flush iova queue before releasing dma_ops_domain
iommu/amd: Handle IOMMU_DOMAIN_DMA in ops->domain_free call-back
iommu/amd: Use dev_data->domain in get_domain()
iommu/amd: Optimize map_sg and unmap_sg
iommu/amd: Introduce dir2prot() helper
iommu/amd: Implement timeout to flush unmap queues
iommu/amd: Implement flush queue
iommu/amd: Allow NULL pointer parameter for domain_flush_complete()
iommu/amd: Set up data structures for flush queue
iommu/amd: Remove align-parameter from __map_single()
iommu/amd: Remove other remains of old address allocator
iommu/amd: Make use of the generic IOVA allocator
iommu/amd: Remove special mapping code for dma_ops path
iommu/amd: Pass gfp-flags to iommu_map_page()
iommu/amd: Implement apply_dm_region call-back
iommu/amd: Create a list of reserved iova addresses
...
Pull mailbox updates from Jussi Brar:
"Broadcom:
- New PDC controller driver and bindings
Misc:
- PL320 - Convert from 'raw' IO to 'relaxed' version
- Test - fix dangling pointer"
* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Fix format and type mismatches in Broadcom PDC driver
mailbox: Add Broadcom PDC mailbox driver
dt-bindings: add bindings documentation for PDC driver.
mailbox: pl320: remove __raw IO
mailbox: mailbox-test: set tdev->signal to NULL after freeing
x86_64 needs to use compat_sys_keyctl for 32-bit userspace rather than
calling sys_keyctl(). The latter will work in a lot of cases, thereby
hiding the issue.
Reported-by: Stephan Mueller <smueller@chronox.de>
Tested-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: keyrings@vger.kernel.org
Cc: linux-security-module@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/146961615805.14395.5581949237156769439.stgit@warthog.procyon.org.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On Acer Veriton machines, codec with subsystem-id 0x1b0a01b8 the port at
0x15 is configured by default as an Internal Speaker (0x90170120).
However, no physical is speaker installed on-board. This patch adds a quirk
which disables the physical connection on this pin.
BugLink: https://bugs.launchpad.net/bugs/1607647
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have a Dell AIO on which we can't adjust its speaker's volume.
The problem is it is connected to a Audio Output node without Amp-out
capability. To fix it, we change it to be connnected to a node with
Amp-out capability.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are KSZ8721 PHYs with phy_id 0x00221619. In order to detect them
as PHY_ID_KSZ8001 compatible while staying different to PHY_ID_KSZ9021
ignore the last two bits when matching PHY_ID
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chunhao Lin says:
====================
r8169: fix 3 runtime pm related issues.
v2:
use "struct device *d = &tp->pci_dev->dev" instead of "struct pci_dev *pdev = tp->pci_dev"
v1:
This series of patches fix 3 runtime pm related issues that are listed below.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
