API version lower than 16 is not supported anymore - don't
load older ucode.
Remove code handling older versions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Gscan capabilities were updated with new capabilities supported
by the device. Update GSCAN capabilities TLV.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We have a module parameter, this is enough.
per platform customizations will be done through the init
script of the platform.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Due to hardware bug, upon any shadow free-queue register write
access, a legacy RBD shadow register must be written as well.
This is required in order to trigger a copy of the shadow registers
values after MAC exits sleep state.
Specifically, the driver has to write (any value) to the legacy RBD
register each time FRBDCB is accessed.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
"DQA" is shorthand for "dynamic queue allocation". This
enables on-demand allocation of queues per RA/TID rather than
statically allocating per vif, thus allowing a potential
benefit of various factors.
Please refer to the DOC section this patch adds to sta.h to
see a more in-depth explanation of this feature.
There are many things to take into consideration when working
in DQA mode, and this patch is only one in a series. Note that
default operation mode is non-DQA mode, unless the FW
indicates that it supports DQA mode.
This patch enables support of DQA for a station connected to
an AP, and works in a non-aggregated mode.
When a frame for an unused RA/TID arrives at the driver, it
isn't TXed immediately, but deferred first until a suitable
queue is first allocated for it, and then TXed by a worker
that both allocates the queues and TXes deferred traffic.
When a STA is removed, its queues goes back into the queue
pools for reuse as needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
"is_data_qos == true" is equivalent to "tid < IWL_MAX_TID_COUNT"
since tid is only assigned (and range-checked) in that case.
This removes a (harmless) smatch warning that occurs because it
can't seem to follow the above logic from the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Update device id and FW serial number for 2X2 antenna devices
in 9000 generation product. These will not be available on
the market in the coming year.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to disable uapsd for BSS only, or P2P client
separately. Remove the now unneeded
IWL_MVM_P2P_UAPSD_STANDALONE constant.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
TX CMD API has changed to support offload assist.
Currently we do not enable checksum yet, but must set the
padding indication, to avoid FW errors.
Set other amsdu flag as well.
The rest of the flags will be configured only if HW csum
is enabled and will be set in future patches.
This change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We insert padding if the MAC header's size is not a multiple of 4
to ensure that the SNAP header is DWORD aligned. When we do so, we
let the firmware know by setting a bit in Tx command
(TX_CMD_FLG_MH_PAD) which will instruct the firmware to drop those
2 bytes before sending the frame.
However, this is not needed for AMSDU as the sub frame header (14B)
complements the MAC header (26B) so that the SNAP header is DWORD
aligned without adding any pad.
Until 9000, the firmware didn't check the TX_CMD_FLG_MH_PAD bit
but rather checked the length of the MAC header itself and
assumed the entity that enqueued the frame (driver or internal
firmware code) added the pad.
Since the driver inserted the pad even for AMSDU this logic applied.
Note that the padding is a DMA optimization but it's not strictly
needed, so we could pad even if it was not needed.
However, the CSUM hardware introduced for the 9000 devices requires
to not pad AMSDU as it is not needed, and will fail if such a pad
exists.
Due to older FW not checking the padding bit but checking the mac
header size itself - we cannot do this adjustments for older
generations.
Do not align the size if it is an AMSDU and HW checksum is enabled -
which will only happen on 9000 devices and on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Bjorn pointed out that printing an error value as an
hexadecimal isn't very convenient. Change that.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use RX_HANDLER_ASYNC_UNLOCKED instead of unlock and re-lock
the mutex independently.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We don't use the refcount value anymore, all the refcounting is done
in the runtime PM usage_count value. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When entering suspend the driver calls iwl_disable_interrupts() and
then iwl_pcie_disable_ict().
On resume the driver calls only iwl_pcie_reset_ict() without calling
explicitly to iwl_enable_interrupts().
This mostly works since iwl_pcie_reset_ict is calling to
iwl_enable_interrupts, but it doesn't work when there is no ict_table
in MSIx mode.
The result is that driver tries to resume but fails since it doesn't
get the RX interrupt from FW indicating that d0i3 exit was completed.
Fix it by adding an explicit call to enable interrupts.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
My patch resized the pool size, but neglected to resize
the global table, which is obviously wrong since the global
table maps the pool's rxb to vid one to one. This results
in a panic in 9000 devices.
Add a build bug to avoid such a case in the future.
Fixes: 7b5424361e ("iwlwifi: pcie: fine tune number of rxbs")
Reported-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add debugfs entry named lqm_send_cmd for kicking a
measurement. This hook takes the duration and the timeout
as parameter.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
LQM stands for Link Quality Measurement. The firmware
will collect a defined set of statitics (see the
notification for details) that allow to know how busy
the medium is. The driver issues a request to the firmware
that includes the duration of the measurement (the firmware
needs to be on channel for that amount of time) and the
timeout (in case the firmware has a lot of offchannel
activities). If the timeout elapses, the firmware will
send partial results which are still valuable.
In case of disassociation / channel switch and alike, the
driver is in charge of stopping the measurements and the
firmware will reply with partial results.
The user space API for now is debugfs only and will be
implmemented in an upcoming patch.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
platform_get_resource() can return NULL, thus add NULL test to prevent NULL
pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code uses a uninitialized spin lock.
bgpio_init() already initialized a spin lock, so let's switch to use
&gc->bgpio_lock instead and remove the lock from struct men_z127_gpio.
Fixes: f436bc2726 "gpio: add driver for MEN 16Z127 GPIO controller"
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix support for 16 bit source/dest port matches in ixgbe model.
u32 uses a single 32-bit key value for both source and destination ports
starting at offset 0. So replace the 2 functions with a single function
that takes this key value/mask to program both source and dest ports.
Verified with the following filter:
#tc qdisc add dev p4p1 ingress
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1: u32 divisor 1
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:10 u32 ht 800: link 1: \
offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:10 u32 ht 1: \
match tcp src 1024 ffff match tcp dst 80 ffff action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:11 u32 ht 1: \
match tcp src 1025 ffff action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 1:0:12 u32 ht 1: \
match tcp dst 81 ffff action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the incorrect check for mask in ixgbe_configure_clsu32 and
drop the 'mask' field that is not required in struct ixgbe_mat_field
Verified with the following filters:
#tc qdisc add dev p4p1 ingress
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:1 u32 ht 800: \
match ip dst 10.0.0.1/8 match ip src 10.0.0.2/8 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:2 u32 ht 800: \
match ip dst 11.0.0.1/16 match ip src 11.0.0.2/16 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:3 u32 ht 800: \
match ip dst 12.0.0.1/24 match ip src 12.0.0.2/24 action drop
#tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:4 u32 ht 800: \
match ip dst 13.0.0.1/32 match ip src 13.0.0.2/32 action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for handle ids when adding/deleting hash nodes OR adding/deleting
filter entries and limit them to max number of links or header nodes
supported(IXGBE_MAX_LINK_HANDLE).
Start from bit 0 when setting hash table bit-map.(adapter->tables)
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function is only used in ixgbe_main.c
Resolves a "missing prototype" warning when building the driver with W=1
Reported-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return error when a MAC address change is rejected by the PF.
This will prevent the user from modifying the MAC address when
that operation is not permitted.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling dev_close() causes IFF_UP to be cleared which will remove the
interfaces routes and some addresses. That's probably not what the user
intended when running the offline selftest. Besides this does not happen
if the interface is brought down before the test, so the current
behaviour is inconsistent.
Instead call the net_device_ops ndo_stop function directly and avoid
touching IFF_UP at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use udelay instead of usleep_range because this can be called while
a lock is held.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ATR code was assuming that it would be able to use tcp_hdr for
every TCP frame that came through. However this isn't the case as it
is possible for a frame to arrive that is TCP but sent through something
like a raw socket. As a result the driver was setting up bad filters in
which tcp_hdr was really pointing to the network header so the data was
all invalid.
In order to correct this I have added a bit of parsing logic that will
determine the TCP header location based off of the network header and
either the offset in the case of the IPv4 header, or a walk through the
IPv6 extension headers until it encounters the header that indicates
IPPROTO_TCP. In addition I have added checks to verify that the lowest
protocol provided is recognized as IPv4 or IPv6 to help mitigate raw
sockets using ETH_P_ALL from having ATR applied to them.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VXLAN port number should be stored in network order instead of in host
order as it is accessed from the hot-path in ATR. This way we can avoid
having to do any byte swaps in order to validate the port number.
I moved the vxlan_port value into a hole in the read-mostly region of the
adapter struct. This way it should be in a warm cache-line instead of in
some isolated region in memory when it needs to be accessed.
In addition I went through and stripped a bunch of unneeded ifdef flags
since having an extra variable present doesn't really hurt anything and
makes the code easier to read. I also went through and dropped the
NETIF_F_RXCSUM flag which was being set in hw_encap_features but provides
no value as the flag is not evaluated in the Rx path.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit c9f53e63c2 ("ixgbe: Refactor MAC address configuration code")
introduced code that doesn't set HW register RAR0 to default mac address
but FF:FF:FF:FF:FF:FF. Due to this, ixgbe HW discards all incoming packets
that doesn't have destination mac address equals to FF:FF:FF:FF:FF:FF.
This commit sets RAR0 correctly to default HW mac address.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drivers for these don't exist yet so we will add them as fixed clocks
so we don't BUG() if we change clocks that reference these clocks.
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When this was added not all the remaining defines were switched over to
use enums, so let's complete that process here
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The qcom_reset_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The rst_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The sunxi_ve_reset_ops, sun9i_mmc_reset_ops, and sunxi_usb_reset_ops
structures are never modified. Make them const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The atlas7_rst_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The rockchip_softrst_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The mmp_clk_reset_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The mtk_reset_ops structure is never modified. Make it const.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
A few defconfig updates got dropped on the floor during the merge window,
so I've rounded up the remainder here:
* Fix duplicate definition of MMC_BLOCK_MINORS and bump to 32 for
msm8916
* CPUFreq support for the Juno platform, using the MHU/SCPI interface
* Removal of the default command line, which assumed a console called
ttyAMA0
* Bits and pieces for the Hi6220 (96Boards HiKey)
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 1ae1602de0 "configfs: switch ->default groups to a linked list"
left the NULL gps pointer behind after removing the kcalloc() call which
made it non-NULL. It also left the !gps check in place so make_cluster()
now fails with ENOMEM. Remove the remaining uses of the gps variable to
fix that.
Reviewed-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
To use the ARMv8 PMU related register defines from the KVM code, we move
the relevant definitions to asm/perf_event.h header file and rename them
with prefix ARMV8_PMU_. This allows us to get rid of kvm_perf_event.h.
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
arm and arm64 use different config options to specify big endian. This
needs taking into account when including code/headers between the two
architectures.
A case in point is PAN, which uses the __instr_arm() macro to output
instructions. The macro comes from opcodes.h, which lives under arch/arm.
On a big-endian build the mismatched config options mean the instruction
isn't byte swapped correctly, resulting in undefined instruction exceptions
during boot:
| alternatives: patching kernel code
| kdevtmpfs[87]: undefined instruction: pc=ffffffc0004505b4
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| kdevtmpfs[87]: undefined instruction: pc=ffffffc00076231c
| Internal error: Oops - undefined instruction: 0 [#1] SMP
| Modules linked in:
| CPU: 0 PID: 87 Comm: kdevtmpfs Not tainted 4.1.16+ #5
| Hardware name: Hisilicon PhosphorHi1382 EVB (DT)
| task: ffffffc336591700 ti: ffffffc3365a4000 task.ti: ffffffc3365a4000
| PC is at dump_instr+0x68/0x100
| LR is at do_undefinstr+0x1d4/0x2a4
| pc : [<ffffffc00076231c>] lr : [<ffffffc0000811d4>] pstate: 604001c5
| sp : ffffffc3365a6450
Cc: <stable@vger.kernel.org> #4.3.x-
Reported-by: Hanjun Guo <guohanjun@huawei.com>
Tested-by: Xuefeng Wang <wxf.wang@hisilicon.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When the prng device driver calls misc_register() there is the possibility
to also provide the recommented file permissions. This fix now gives
useful values (0644) where previously just the default was used (resulting
in 0600 for the device file).
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The used_vsr flag is set if process has used VSX registers, not Altivec
registers. But the comment says otherwise, correct the comment.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In save_sprs() in process.c contains the following test:
if (cpu_has_feature(cpu_has_feature(CPU_FTR_ALTIVEC)))
t->vrsave = mfspr(SPRN_VRSAVE);
CPU feature with the mask 0x1 is CPU_FTR_COHERENT_ICACHE so the test
is equivilent to:
if (cpu_has_feature(CPU_FTR_ALTIVEC) &&
cpu_has_feature(CPU_FTR_COHERENT_ICACHE))
On CPUs without support for both (i.e G5) this results in vrsave not
being saved between context switches. The vector register save/restore
code doesn't use VRSAVE to determine which registers to save/restore,
but the value of VRSAVE is used to determine if altivec is being used
in several code paths.
Fixes: 152d523e63 ("powerpc: Create context switch helpers save_sprs() and restore_sprs()")
Cc: stable@vger.kernel.org
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
hugepd_free() used __get_cpu_var() once. Nothing ensured that the code
accessing the variable did not migrate from one CPU to another and soon
this was noticed by Tiejun Chen in 94b09d7554 ("powerpc/hugetlb:
Replace __get_cpu_var with get_cpu_var"). So we had it fixed.
Christoph Lameter was doing his __get_cpu_var() replaces and forgot
PowerPC. Then he noticed this and sent his fixed up batch again which
got applied as 69111bac42 ("powerpc: Replace __get_cpu_var uses").
The careful reader will noticed one little detail: get_cpu_var() got
replaced with this_cpu_ptr(). So now we have a put_cpu_var() which does
a preempt_enable() and nothing that does preempt_disable() so we
underflow the preempt counter.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update the definition of memcpy_from_pmem() to return 0 or a negative
error code. Implement x86/arch_memcpy_from_pmem() with memcpy_mcsafe().
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
