When an NL80211_DISCONNECT is sent to cfg80211, the driver's cfg80211
disconnect function sets the sme_state to SME_DISCONNECTED before receiving
a WMI_DISCONNECT_EVENT from the firmware. This caused cfg80211 to not know
that the connection is disconnected because the driver fails to notify
cfg80211 upon receiving WMI_DISCONNECT_EVENT from the firmware believing
it is already disconnected.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We only get nf_connlabels if the user add ct label set expr successfully,
but we will also put nf_connlabels if the user delete ct lable get expr.
This is mismathced, and will cause ct label expr cannot work properly.
Also, if we init something fail, we should put nf_connlabels back.
Otherwise, we may waste to alloc the memory that will never be used.
Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When disabling tethering after having enabled it, the ath6kl driver does
not set the IFF_LOWER_UP flag to 0 (carrier off) on the wlan interface.
The upper layers (eg. connman) are not notified of the tethering mode
status change. So, tethering can not be activated anymore.
This patch adds a netif_carrier_off() call when stopping AP mode to fix
the problem.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One minute after a successful connection, the kernel checks if the
frequency and the channel width are well configured for the country we
are in. (regulatory domain)
ath6kl driver was setting the NL80211_CHAN_HT20 channel without checking
for the HT capabilities. (we should have NL80211_CHAN_NO_HT in our
case because the firmware did not support HT)
This patch adds a check on ht_cap.ht_supported in order to create the
channel corresponding to the firmware capabilities.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When enabling WLAN tethering, a new AP is visible and a STA could
connect to it. When the STA tries to authenticate to the newly created
AP, the WPA authentication mechanism is stuck in the 1/4 msg of 4-Way
Handshake.
In ath6kl_rx(), the ath6kl_find_sta() function is looking for the
h_source field of the Ethernet frame header received by the STA. The
datap pointer that points to the Ethernet frame header is incorrect,
and was pointing at the wrong offset in the buffer.
This commit adds a pad_before_data_start offset to set the datap pointer
to the Ethernet frame header. datap->h_source parameter is now really
pointing to the source ethernet address and the authentication process
can continue.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ideally wake_tx_queue should be used regardless as
it is a requirement for reducing bufferbloat and
implementing airtime fairness in the future.
However some setups (typically low-end platforms
hosting QCA988X) suffer performance regressions
with the current wake_tx_queue implementation.
Therefore disable it unless it is really
beneficial with current codebase (which is when
firmware supports smart pull-push tx scheduling).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As promised here's the pile of kbl cherry-picks assembled by Mika&Rodrigo.
It's a bit much, but all well-contained to kbl code and been tested for a
while in drm-intel-next. Still separate in case too much, but in that case
I think we'd need to disable kbl by default again (which would be annoying
too) in 4.7.
* tag 'topic/kbl-4.7-fixes-2016-07-18' of git://anongit.freedesktop.org/drm-intel: (28 commits)
drm/i915/kbl: Introduce the first official DMC for Kabylake.
drm/i915: Introduce Kabypoint PCH for Kabylake H/DT.
drm/i915/gen9: implement WaConextSwitchWithConcurrentTLBInvalidate
drm/i915/gen9: Add WaFbcHighMemBwCorruptionAvoidance
drm/i195/fbc: Add WaFbcNukeOnHostModify
drm/i915/gen9: Add WaFbcWakeMemOn
drm/i915/gen9: Add WaFbcTurnOffFbcWatermark
drm/i915/kbl: Add WaClearSlmSpaceAtContextSwitch
drm/i915/gen9: Add WaEnableChickenDCPR
drm/i915/kbl: Add WaDisableSbeCacheDispatchPortSharing
drm/i915/kbl: Add WaDisableGafsUnitClkGating
drm/i915/kbl: Add WaForGAMHang
drm/i915: Add WaInsertDummyPushConstP for bxt and kbl
drm/i915/kbl: Add WaDisableDynamicCreditSharing
drm/i915/kbl: Add WaDisableGamClockGating
drm/i915/gen9: Enable must set chicken bits in config0 reg
drm/i915/kbl: Add WaDisableLSQCROPERFforOCL
drm/i915/kbl: Add WaDisableSDEUnitClockGating
drm/i915/kbl: Add WaDisableFenceDestinationToSLM for A0
drm/i915/kbl: Add WaEnableGapsTsvCreditFix
...
Two more regression fixes for 4.7.
* tag 'drm-intel-fixes-2016-07-18' of git://anongit.freedesktop.org/drm-intel:
drm/i915: add missing condition for committing planes on crtc
drm/i915: Treat eDP as always connected, again
Do not cache pointers into the skb linear segment across sk_filter.
The function call can trigger pskb_expand_head.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kernel HTB keeps tokens in signed 64-bit in nanoseconds. In netlink
protocol these values are converted into pshed ticks (64ns for now) and
truncated to 32-bit. In struct tc_htb_xstats fields "tokens" and "ctokens"
are declared as unsigned 32-bit but they could be negative thus tool 'tc'
prints them as signed. Big values loose higher bits and/or become negative.
This patch clamps tokens in xstat into range from INT_MIN to INT_MAX.
In this way it's easier to understand what's going on here.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should use kfree_skb() instead of kfree() to free an skb.
Fixes: 362899b872 ("macvtap: switch to use skb array")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 1bdf02326b ("clk: at91: make use of syscon/regmap
internally"), clk_programmable_set_parent() is always selecting the
first parent (AKA slow_clk), no matter what's passed in the 'index'
parameter.
Fix that by initializing the pckr variable to the index value.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Fixes: 1bdf02326b ("clk: at91: make use of syscon/regmap internally")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1468828152-18389-1-git-send-email-boris.brezillon@free-electrons.com
So far we had only MIPS devices with serial flash connected to the SoC's
ChipCommon. ARM devices got a separated SPI controller and weere using
standard SPI drivers.
This has changed with the wireless SoC BCM47189B0. It's ARM based but
has serial flash attached just like older devices. This allows using
existing driver with these devices.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Same skb is being reused for storing command response from firmware
in PCIe chipsets. There was a bug while updating the skb length.
This patch ensures skb length correctly gets updated based on rx_len.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In corner case, we may end up processing same interrupt twice.
We have a logic to read pending interrupts at the end of interrupt
processing routine. It has a race with interrupts read in interrupt
handler. This patch solves the problem by ORing the interrupt bitmap
in this case.
The symptom for this bug is below messages in dmesg log.
[ 11.522123] mwifiex_pcie 0000:01:00.0: CMD_RESP: invalid cmd resp
[ 11.680412] mwifiex_pcie 0000:01:00.0: There is no command but got cmdrsp
Link: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that request_irq() failure leads to a system crash
due to a bug in mwifiex driver.
When this failure happens, mwifiex_add_card() already takes care of
clearing and freeing adapter->card pointer. This patch removes the
redundant cleanup code causing crash.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The sdio dpc starts processing when in SDIOD_STATE_DATA. This state was
entered right after firmware download. This patch moves that transition
just before enabling sdio interrupt handling thus avoiding watchdog
expiry which would put the bus to sleep while probing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the host-interface bus has hard time handling transmit packets
it informs higher layer about this and it would stop the netdev
queue when needed. However, since commit 9cd18359d3 ("brcmfmac:
Make FWS queueing configurable.") this was broken. With this patch
the behaviour is restored.
Cc: stable@vger.kernel.org # v4.5, v4.6, v4.7
Fixes: 9cd18359d3 ("brcmfmac: Make FWS queueing configurable.")
Tested-by: Per Förlin <per.forlin@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
memory is malloced in mwifiex_cfg80211_start_ap() and should be
freed before leaving from the error handling cases, otherwise it
will cause memory leak.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warning:
drivers/net/wireless/marvell/libertas/cfg.c:2047:5: warning:
symbol 'lbs_set_power_mgmt' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After discovering there are 2 very different 14e4:4365 PCI devices we
made ID tables less generic. Back then we believed there are only 2 such
devices:
1) 14e4:4365 1028:0016 with SoftMAC BCM43142 chipset
2) 14e4:4365 14e4:4365 with FullMAC BCM4366 chipset
>From the recent report it appears there is also 14e4:4365 105b:e092
which should be claimed by bcma. Add back support for it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=121881
Fixes: 515b399c9a ("bcma: claim only 14e4:4365 PCI Dell card with SoftMAC BCM43142")
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Stable <stable@vger.kernel.org> [4.6+]
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adding this opcode, allows the TI wireless driver,
to report throughput directly from FW to mac80211.
This is used mainly for mesh metric calculation.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[kvalo@codeaurora.org: fix indentation]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW will provide a TX rate per link for each FW status,
and wlcore will be able to store the information for
the use of the mesh hwmp module.
This is used mainly in mesh.
Rates are reported when a mesh interface is up.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The dummy ruleset I used to test the original validation change was broken,
most rules were unreachable and were not tested by mark_source_chains().
In some cases rulesets that used to load in a few seconds now require
several minutes.
sample ruleset that shows the behaviour:
echo "*filter"
for i in $(seq 0 100000);do
printf ":chain_%06x - [0:0]\n" $i
done
for i in $(seq 0 100000);do
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
done
echo COMMIT
[ pipe result into iptables-restore ]
This ruleset will be about 74mbyte in size, with ~500k searches
though all 500k[1] rule entries. iptables-restore will take forever
(gave up after 10 minutes)
Instead of always searching the entire blob for a match, fill an
array with the start offsets of every single ipt_entry struct,
then do a binary search to check if the jump target is present or not.
After this change ruleset restore times get again close to what one
gets when reverting 3647234101 (~3 seconds on my workstation).
[1] every user-defined rule gets an implicit RETURN, so we get
300k jumps + 100k userchains + 100k returns -> 500k rule entries
Fixes: 3647234101 ("netfilter: x_tables: validate targets of jumps")
Reported-by: Jeff Wu <wujiafu@gmail.com>
Tested-by: Jeff Wu <wujiafu@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This was succesfully tested with 4366B1. A small workaround is needed
for the main interface otherwise it would stuck at the hidden state.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1. Added support for interface and role of mesh type.
2. Enabled enable/start of mesh-point role,
and opening and closing a connection with a mesh peer.
3. Added multirole combination of mesh and ap
under the same limits of dual ap mode.
4. Add support for 'sta_rc_update' opcode for mesh IF.
The 'sta_rc_update' opcode is being used in mesh_plink.c.
Add support in wlcore to handle this opcode correctly for mesh
(as opposed to current implementation that handles STA only).
5. Bumped the firmware version to support new Mesh functionality
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For multiple REG Host Commands (e.g HostCmd_CMD_802_11_EEPROM_ACCESS,
HostCmd_CMD_MAC_REG_ACCESS etc.) "cpu_to_leX"-converted values are
saved to driver. So, "leX_to_cpu" conversion is required too many
times afterwards in driver.
This patch reduces the endian: conversion without saving "cpu_to_leX"
converted values in driver. This will convert endianness in prepare
command and command response path.
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Version 1.01.
This firmware is made for Kabylake platform so it doesn't
need the stepping workaround that we had before.
v2: Rebased on top of latest nightly with min version
required change.
v3: With right CSR_VERSION (Patrik).
Cc: Christophe Prigent <christophe.prigent@intel.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com> (v1)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461707991-15336-1-git-send-email-rodrigo.vivi@intel.com
(cherry picked from commit 4922d49195)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The i915 driver checks for color management properties changes as part
of a plane update. Therefore a color management update must imply a
plane update, otherwise we never update the transformation matrixes
and degamma/gamma LUTs.
v2: add comment about moving the commit of color management registers
to an async worker
v3: Commit color management register right after vblank
v4: Move back color management commit condition together with planes
commit
v5: Trigger color management commit through the planes commit (Daniel)
v6: Make plane change update more readable
Fixes: 20a34e78f0 (drm/i915: Update color management during vblank evasion.)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
References: https://lkml.org/lkml/2016/7/14/614
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464183041-8478-1-git-send-email-lionel.g.landwerlin@intel.com
(cherry picked from commit e7852a4b3a)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDP should be treated as connected even if doesn't have an EDID. In that
case we'll use the timings from the VBT. That used to be the case until
commit f21a21983e ("drm/i915: Splitting intel_dp_detect")
broke things by considering even eDP disconnected if we fail to get
an EDID for it.
Fix things up again by treating eDP as always connected.
Cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Cc: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Larry Finger <larry.finger@lwfinger.net>
Reported-by: Larry Finger <larry.finger@lwfinger.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96675
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: f21a21983e ("drm/i915: Splitting intel_dp_detect")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Larry Finger <larry.finger@lwfinger.net>
Link: http://patchwork.freedesktop.org/patch/msgid/1468836914-16537-1-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 1b7f2c8b07)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As reported by Dan in his report in [1], there is a potential NULL
pointer derefence if these conditions are met :
- there is no platform_data provided, ie. host->pdata = NULL
Fix this by only using the platform data ro_invert when a gpio for
read-only is provided by the platform data.
This doesn't appear yet as every pxa board provides a platform_data, and
calls pxa_set_mci_info() with a non NULL pointer.
[1] [bug report] mmc: pxamci: fix card detect with slot-gpio API.
The commit fd546ee6a7 ("mmc: pxamci: fix card detect with slot-gpio
API") from Sep 26, 2015, leads to the following static checker warning:
drivers/mmc/host/pxamci.c:809 pxamci_probe()
warn: variable dereferenced before check 'host->pdata' (see line 798)
Fixes: fd546ee6a7 ("mmc: pxamci: fix card detect with slot-gpio API")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code that fills packed command header assumes that CPU runs in
little-endian mode. Hence the header is malformed in big-endian mode
and causes MMC data transfer errors:
[ 563.200828] mmcblk0: error -110 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc40
[ 563.219647] mmcblk0: packed cmd failed, nr 2, sectors 16, failure index: -1
Convert header data to LE.
Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Fixes: ce39f9d17c ("mmc: support packed write command for eMMC4.5 devices")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set 'idata->buf' to NULL so that it never gets returned without
initialization. This fixes a bug where mmc_blk_ioctl_cmd() would
free both 'idata' and 'idata->buf' but 'idata->buf' was returned
uninitialized.
Fixes: 1ff8950c04 ("mmc: block: change to use kmalloc when copy data from userspace")
Signed-off-by: Ville Viinikka <ville@tuxera.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
is_suspending flag remains on when host sleep fails to enable. Data
path is unnecessarily blocked after this. This patch ensures to
reset the flag in failure path.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Digianswer sniffer devices allow for reading a firmware specific
information string. If it is available, then inform the Bluetooth core
about it via hci_set_fw_info. That exposes it via debugfs like this:
# cat /sys/kernel/debug/bluetooth/hci0/firmware_info
SNIF_102,BB930,02/01/18,10:37:56
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some Bluetooth controllers allow for reading hardware and firmware
related vendor specific infos. If they are available, then they can be
exposed via debugfs now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The protoypes for hci_recv_frame and hci_recv_diag are in the wrong
location in the header file. Move them close to all the other hci_dev
related exported functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
There was a check on CAP_NET_ADMIN in bfin_mac_ethtool_setsettings,
but this check is already done in dev_ethtool, so no need to repeat
it before calling the generic function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_workqueue replaces deprecated create_singlethread_workqueue().
A dedicated workqueue has been used since the workitem viz
lp->txtimeout_reinit is involved in reinitialization if a TX timeout
occurs, which is necessary to guarantee forward progress in packet
processing. As a network device can be used during memory reclaim, the
workqueue needs forward progress guarantee under memory pressure.
WQ_MEM_RECLAIM has been set to ensure this.
Since there is only a single work item, explicit concurrency limit is
unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arbitrary X.509 certificates without authority key identifiers (AKIs)
can be added to "trusted" keyrings, including IMA or EVM certs loaded
from the filesystem. Signature verification is currently bypassed for
certs without AKIs.
Trusted keys were recently refactored, and this bug is not present in
4.6.
restrict_link_by_signature should return -ENOKEY (no matching parent
certificate found) if the certificate being evaluated has no AKIs,
instead of bypassing signature checks and returning 0 (new certificate
accepted).
Reported-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Commit e68503bd68 forgot to set digest_len and thus cause the following
error reported by kexec when launching a crash kernel:
kexec_file_load failed: Bad message
Fixes: e68503bd68 (KEYS: Generalise system_verify_data() to provide access to internal content)
Signed-off-by: Lans Zhang <jia.zhang@windriver.com>
Tested-by: Dave Young <dyoung@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
cc: kexec@lists.infradead.org
cc: linux-crypto@vger.kernel.org
Signed-off-by: James Morris <james.l.morris@oracle.com>
